擠塑法 的英文怎麼說
中文拼音 [jǐsùfǎ]
擠塑法
英文
extrusion molding-
The comparison between experimental results and theoretical results show that to calculate the value of crushing hole in roller chain plate has practical significance
結果表明,用彈塑性有限變形理論和有限元方法計算出的鏈板最佳擠孔量具有工程實際上的可用性。Two common methods of manufacturing plastic articles are by extrusion and by injection moulding.
生產塑料製品的兩種通用方法是擠出成型法和注射成型法。08. 01 flow rate of thermoplastics by extrusion plastometer, test method for
擠壓式塑性計測試熱塑性塑料流速的方法Standard test method for melt flow rates of thermoplastics by extrusion plastometer
使用擠壓式塑性計測定熱塑塑料的熔融流量率的標準試驗方法Synthetic resin product extrusion forming machining
合成樹脂擠壓塑膜法加工業In the dissertation high - temperature corundum honeycombed ceramic regenerative body was prepared by an extrusion process, a - al2o3 minute powder as main raw material, clay, cmc etc as plasticizers, tung oil etc as lubricator. the plastic performance was tested on a plastic measure apparatus
以a - al _ 2o _ 3微粉料為主原料,採用粘土、羧甲基纖維素( cmc )等有機-無機復合增塑劑,加入桐油等作為潤滑劑,採用擠出成型法制備剛玉質高溫型蜂窩陶瓷蓄熱體。Basic silicones for industrial use. determination of extrudability fluidity and of viscosity " casson ". method using standard extrusion nozzle
工業用基礎硅塑料.擠壓度流動性和粘度的測定.標準擠壓噴嘴法Test method for flexural properties
拉擠玻璃纖維增強塑料桿彎曲性能試驗方法Test method for tensile properties
拉擠玻璃纖維增強塑料桿拉伸性能試驗方法Test method for in plane shear
拉擠玻璃纖維增強塑料桿面內剪切強度試驗方法Test method for flexural properties of fiber reinforced pultruded plastic rods
纖維增強拉擠塑料棒彎曲特性試驗方法Test method for tensile properties of pultruded glass fiber reinforced plastic rods
拉擠玻璃纖維增強塑料桿拉伸性能試驗方法Test method for flexural properties of pultruded glass fiber reinforced plastic rods
拉擠玻璃纖維增強塑料桿彎曲性能試驗方法Test method for inplane shear strength of pultruded glass fiber reinforced plastic rods
拉擠玻璃纖維增強塑料桿面內剪切強度試驗方法Standard practice for injection molding test specimens of thermoplastic molding and extrusion materials
熱模塑和擠塑材料的噴射模塑法試樣標準規程4. the reinforced and toughened pp / pa66 and pp / pa66 / gpp in - situ composites were firstly prepared via extrusion - drawing - injection method
首次採用擠出?拉伸?注塑法制備了pp pa66 、 pp pa66 gpp原位復合材料,取得了增強又增韌的效果。Methods of specifying general purpose polyethylene materials for moulding and extrusion
模塑和擠塑通用聚乙烯材料的規定方法Plastic barrier adopts hard material with special character, by way of pushing and infusing, it come into standing pole, rail, barrier, etc, which is completed by using welding, sticking, hooking and inserting
塑膠柵欄採用特殊性能的硬質材料,用擠塑和注塑的加工方法製成立柱,橫桿,柵桿和帽頭等部件,利用焊接,粘接,扣接和插接的方法組裝而成。Application development and process support that require conventional plastics converting technologies , such as injection molding , screw extrusion and compression molding , to move customer programs from concept to commercialization
應用發展和工藝支持要求了解傳統的塑料吹煉技術工藝,如噴射模塑法、擠壓、澆鑄等,使客戶從概念轉入商業運作。Method of specifying general purpose polypropylene and propylene copolymer materials for moulding and extrusion
通用模塑和擠塑聚丙烯和丙烯共聚物材料規定方法分享友人