擠壓節理 的英文怎麼說
中文拼音 [jǐyājiélǐ]
擠壓節理
英文
compre ionjoint-
The fault controlled the magmatism and metallization relevant to the contact zone, and deformed successively and produced cataclastic rocks and two sets of joints ; the second stage was from late cretaceous to eocene. the fault zone deformed right - laterally under ne - sw striking transtention, and new joints zone was produced at the end of the two main faults because of local stress concentration. the fault produced inchoative cataclastic rocks, and two sets of typical joints in plutons ; the third stage of deformation was relatively faint and only a little of microcracks was produced and infilled with vei ns in the deformed rocks, which was during the himalayan movement
其後的繼承性活動在斷裂帶內形成碎裂程度最強達到碎裂巖的碎裂巖系列構造巖，變形帶兩側發育兩組典型的共軛剪節理；第二次在晚白堊世?始新世，斷裂在北東?南西向近水平擠壓作用下右行張扭性活動，斷裂帶兩主斷裂在斜列重疊的端部由於局部應力集中進一步擴展形成節理帶，而斷裂在巖體區也發育兩組典型的共軛剪節理，斷裂內形成初碎裂巖為主的構造巖；第三次是喜山期以西側抬升、東側下降的強烈升降為主的活動，在基巖中，主斷層兩側圍巖出現微破裂。Factors effecting service life of extrusion mold have been analysed and corresponding measures for design, manufacture, heat treatment, mold management and use have been put forword to clarify importance of improvement on service life of mold
摘要對影響擠壓模具壽命的因素進行了分析，並針對設計、製造、熱處理、模具管理和使用等各環節給予相應的措施，從而闡明了提高模具使用壽命的重要性。Those two phases of conjugated shear joints are differ from each other in spatial distribution, which is a reflection of the spatial evolution of the fault zone. it can beinferredfrom the information about macrostructure, superimposed deformation of tectonites, paleotectonic stress field of joints and other related documents that there had been three stages of significant activity since zijingguan fault zone was activated. the first stage was about from middle juiassic to early cretaceous, when the fault zone activated left - laterally under nw - se striking transpression
宏觀構造組合特徵、構造巖變形疊加信息、節理的古構造應力場信息及前人區域資料表明，紫荊關斷裂帶自古生代末開始活化以來有三次主要構造活動：第一次是中侏羅世?早白堊世，在北西?南東向近水平擠壓作用下，斷裂左行壓扭性活動，控制太行山地區巖漿巖帶及與其相關的接觸交代型礦床的形成。A gear pump is installed on the production line, the pressure is stabilized by varying the speed of extruder through the help of computer according to the accurately measured pre - pump pressure, resulting optimized material feeding process
在擠出生產線上安裝一臺齒輪泵，通過在泵前準確的測壓，通過微機處理調節擠出機速度，保持壓力穩定，有序提供料流來優化供料過程。Based on the productive experiment on heihe dam site, during april to august 2002, site experiment was made on gongboxia hpp dam site, bjy - 40 extrusion curb placing machine was determined to be applied into gongboxia project, the batch ratio is : cement 80kg / m3, sand 651kg / m3, small stone 1449kg / m3, and sand ratio 31 %, w / c ratio 1. 31, admixture 3 %
在生產性試驗的基礎上， 2002年4 8月，在公伯峽面板壩現場進行了擠壓邊墻施工各個環節的試驗，通過試驗，確定公伯峽面板壩使用陜工局西安理工大學工程項士學位論文水利機械廠研製的bjy 40型混凝土邊墻擠壓機進行固坡施工，其混凝土配合比為：水泥80kgb 』 ，砂651kgb3 ，小石1449kgb 』 ，砂率31 ，水灰比1分享友人