擬基本解 的英文怎麼說

中文拼音 [nǐjīběnjiě]
擬基本解 英文
parametrix
  • 擬 : 動詞1. （設計; 起草） draw up; draft 2. （打算; 想要） intend; plan 3. （模仿） imitate
  • 本 : i 名詞1 （草木的莖或根）stem or root of plants 2 （事物的根源）foundation; origin; basis 3 （本錢...
  • 解 : 解動詞（解送） send under guard
  1. One of them, the analog computer, is used essentially for problems involving measurements.

    一種是模擬計算機，它基本上是用來解決包含有測量值的問題。
  2. And the explicit finite difference method, the combining method of the central difference method and newmark s constant average acceleration method, and the transmitting boundary are used. by comparing the acceleration determined by the several methods of the displacements or velocities, a computing method of acceleration employed the one side difference of velocity is more practicality in this research. corresponding to normal incidence of the body waves, p waves or svwaves, and rayleigh surface waves, two two - dimensional finite difference programs are compiled to compu te the dynamic response of two - phase media

    以土力學模型為基礎，利用以土骨架和孔隙流體的四個位移為基本未知量的數值方法去模擬二維飽水介質中的地震波傳播，採用了顯式差分方法（中心差分法和newmark常平均加速度法結合）和透射邊界，通過比較利用幾種差分格式求解的加速度結果，發現一種用速度單邊差分求解加速度的方法在本文研究中較為實用，分別編制了體波（ p波或sv波） 、 rayleigh面波輸入時求解兩相介質動力響應的兩個二維數值分析程序。
  3. 3. as to vehicle - bridge system coupling vibration, this difficulty in engineering industry, it was abstractly summarized in this thesis, and introduce a method to establish and resolve equations about such coupling vibration, bring forward a flow chart to write correlative software ; with the help of ansys, make out some work about preparatory simulation, so as to research basic point of chicle - bridge system coupling vibration

    3 、對車橋耦合振動這一業內的難點進行了理論上的分析，引入了一種建立和求解車橋耦合振動系統方程的較為典型的方法，提出了一份自行編製程序的流程簡圖；借用ansys軟體對該橋做了車橋耦合振動的初步模擬計算，探索車橋共振的基本特點。
  4. Analysis the cause of channel disaccord of gain and phase, give four methods of gain and phase calibration, computer simulation illustrate the that the methods are effective. in the chapter 4, the basic relation of phase interferometer of one dimension, two dimensions, and the measurement accuracy and the approach of solving the phase ambiguity in the phase interferometers have been discussed in detail

    第四章對相位干涉儀進行了較為詳細和系統的研究，給出一維相位干涉儀的基本關系式，分析了五通道相位干涉儀測向定位演算法及其性能指標，對解相位模糊問題進行了探討，在ccss中模擬了測向演算法，模擬結果證明了演算法的正確性。
  5. The basic principle and method of 3d stochastic modeling of sedimentary microfacies are discussed according to geological and acoustic impedance data of well - logging constrained seismic inversion, and a case study according to stochastic modeling of fluvial facies reservoir of the minghuazhen formation of neocene in a certain block of bohai bay basin is used to show the general process of this research

    摘要探討了綜合應用地質及測井約束地震反演信息進行三維沈積微相隨機建模的基本原理、思路與方法， ?以渤海灣盆地某區塊新近系明化鎮組河流相儲層?例，說明這一研究過程的基本步驟，包括井眼沉積微相解釋、測井約束地震反演、波阻抗與地質相的概率關系分析、隨機模擬方法選擇、地質統計特徵分析、三維隨機建模、隨機模擬預測的多解性評價。
  6. This paper starts the research of the liquid floated pendulous accelerometer testing system according to the engineering. at first, this paper gives the brief introduction of the history and present status of accelerometer and its testing technology, the working principium and math model of the liquid floated pendu - lous accelerometer, and then, decides the binary width pulse force retrim loop as the design proposal of testing system, researches the transfer function of every part in the system emphasizly, analyses the stability of the whole accelerometer testing system from the angle of control theoretics by the open loop transfer function of system, and designed the correcting net, analyses the basal problems such as resolution, sampling restraint, precision and so on, designs the hardware testing circuits such as preamplification, band - pass filter, alternating amplifier, phase sensitive demodulatorn, pulse - width modulation, frequency scale circuit, moment current generator. finally, using the graphics program language labv - iew which is designed for testing field especially by ni accomplishes the solfware design of testing system, realized the testing functions

    首先對加速度計及其測試技術的發展歷史和現狀，液浮擺式加速度計的工作原理和數學模型等作了簡要的介紹，然後確定了以二元調寬脈沖再平衡測試迴路為設計方案，並從控制理論的角度進行了分析，著重研究了系統中各部分的傳遞函數，利用系統開環傳遞函數分析了系統的穩定性，同時設計了系統的校正網路;分析了二元調寬脈沖再平衡測試迴路的解析度、采樣約束以及測試精度等基本問題，並按照系統分析的結果設計了包括前置放大、帶通濾波、交流放大、相敏解調、脈寬調制、頻標電路以及力矩電流發生器等測試系統各部分硬體電路，驗證了電路的正確性，最後按照測試系統的要求，採用了美國ni公司專為測試領域所開發的虛擬儀器工具? ? labview作為測試軟體開發工具，利用該圖形化編程語言完成了測試系統軟體部分的設計，實現了測試功能。
  7. Comparing with the basic financial instruments, the derivative financial instruments have the peculiarities as followed ( l ) the derivative financial instruments are depended on the basic financial instruments ; ( 2 ) the value of the derivative financial instruments showes an obvious fluctuation ; ( 3 ) the business of the derivative financial instruments attributes go credit business, which has leverage ; ( 4 ) using the derivative financial instruments can elude the risks in a certain extent ; ( 5 ) the derivative financial instruments have very supernal risks ; ( 6 ) the conformation of the derivative financial instruments is very complex, which is difficult to understand to common investors ; ( 7 ) the business of the derivative financial instruments showes dummy ; ( 8 ) the business of the derivative financial instruments showes uncertainty

    與基本金融工具相比，衍生金融工具的特點主要表現在： （ 1 ）衍生金融工具依存於基本金融工具； （ 2 ）衍生金融工具的價值具有明顯的波動性； （ 3 ）衍生金融工具的交易屬于信用交易，具有杠桿作用； （ 4 ）利用衍生金融工具可以在一定程度上規避風險； （ 5 ）衍生金融工具具有極高的風險性； （ 6 ）衍生金融工具的構造靈活復雜，難以為一般投資者理解； （ 7 ）衍生金融工具具有虛擬性； （ 8 ）衍生金融工具交易具有不確定性。
  8. This paper researches the basic statistical rule of oil - gas dynamic system from the systematic theory, combining with the common characteristic and structure characteristic of oil - gas dynamic system, taking the design requirement of oil field development programming into consideration, by using of functional simulation principle ( including nn method, differential simulation method ) and historical data of oil field, establishes the in - out conjunctional relationship of dynamic index of oil field development, and researches the two level index prediction of development dynamic with both oil field and oil production plant on the basis of the in - out conjunctional relationship. furthermore, this paper analyzes the " decision - making variable ", " object " and " restriction terms " by the optimization theory and set up several optimal models which compose the oil field development programming, it is following : optimization model of the production composing ( solving the optimal composing of each subentry production and cor responding cost, workload, including the onshore thin oil production, the heavy oil thermal process production, tertiary oil recovery production, and the offshore production ) ; optimization model of measure production structure ( determining the optimal composing of each measure production and measure workload, which is composed of fracture, acidulation, capital repair and so on ) ; optimization model of the production distraction ( optimal distribution of the whole oil field production to each oil production plant ) and the integrated development programming model of oil field

    本文從系統理論出發研究油氣動態系統基本統計規律，結合油氣動態系統的一般特點，結構特點，兼顧油田開發規劃設計的要求，利用功能模擬原理（含神經網路方法、微分模擬方法） ，依據油田歷史數據，建立了油田開發動態指標間的輸入輸出關聯關系，並在此輸入輸出關聯關系的基礎上研究了油田及採油廠兩級的開發動態指標預測，同時利用最優化原理，在分析「決策變量」 、 「目標」及「約束條件」的基礎上建立了多個構成油田開發規劃的「優化模型」 ，這些優化模型包括：產量構成優化模型（解決陸上稀油產量、稠油熱采產量、三次採油產量、海上產量及對應的成本、工作量的最優構成問題） ；措施產量結構優化模型（解決壓裂、酸化、大修等各項措施產量及措施工作量的最優構成問題） ；產量分配優化模型（將油田的產量最優地分配到各採油廠）以及油田綜合開發規劃模型。
  9. More and more people begin to attach importance to its potence gradually. according to the basic principle of vbi, this paper acquires related experience from the advanced technique for delivering of control signals during the period of vbi. it introduces a scheme using a single coaxial - cable to transmit video signals and control signals simultaneously, in which the key technique is the transmission of control signals in the vertical blanking interval of video signals

    本文根據場消隱期傳輸技術的基本原理，通過借鑒國內外場消隱期傳輸信號的先進技術和相關經驗，提出一種新型的綜合數據傳輸業務的應用電視，闡述了其圖像信號和控制信號共纜傳輸的總體設計方案，並結合bch糾錯編解碼技術和systemview動態模擬軟體，實現和驗證了控制信號在場消隱期間的穩定可靠傳輸。
  10. By mapping input data into a high dimensional characteristic space in which an optimal separating hyperplane is built, svm presents a lot of advantages for resolving the small samples, nonlinear and high dimensional pattern recognition, as well as other machine - learning problems such as function fitting

    Svm的基本思想是通過非線性變換將輸入空間變換到一個高維空間，然後在這個新的空間中求取最優分類超平面。它在解決小樣本、非線性及高維模式識別問題中表現出許多特有的優勢，並能夠推廣應用到函數擬合等其他機器學習問題中。
  11. At last, control circuit of one cycle controlled bridge switching power amplifier is improved with the basic idea of one cycle control. the simulation results show that the amplifier of improved control circuit not only solve the question of output dc offset, but also keep the voltage gain lowered by voltage compensation technique

    最後，根據單周控制的基本思路，改進了單周控制的全橋開關功率放大器的控制電路。模擬結果表明，改進控制電路后的系統不但解決了輸出直流偏置問題，而且解決了電壓補償方法所造成的放大器增益下降問題。
  12. Numerical simulation signal and vibration acceleration signal of a roughing mill main drive speed reduction unit have been decomposed by using empirical mode decomposition algorithm ; each component has been carried on spectral analysis

    摘要運用經驗模式分解演算法對數值模擬信號及某軋鋼廠粗軋機主傳動減速機振動加速度信號進行了分解，從而得到若干個基本模式分量，對每個模式分量進行了頻譜分析。
  13. Because of the unique issues in the networks, including mobility - induced disconnection, network partition, high out - of - order delivery ratios and channel errors, the congestion control and the error recovery in the network is challenging. in this environment, the interaction between tcp and mac layer protocols, the affection of route protocols on the performance of tcp and the particular congestion control and error recovery mechanism are first discussed. then a particular transport layer protocol scheme based on the non - feedback mechanism is presented, with emphasis on the analysis and simulation of the key parameter

    文中主要討論了兩種不同網路結構中的無線tcp協議改進方案，其一在最後一跳為無線鏈路的網路環境中，針對基本tcp擁塞控制機制存在的缺陷，文中在現有解決方案的基礎上提出一綜合性的方案，其中包括無線鏈路的高誤碼率和連接斷開問題的解決，並重點對方案中出現的交叉層問題進行分析和模擬；其二，考慮的是分散式網路（ adhoc ） ，在文中較為詳細的分析了tcp和mac層機制間的相互作用、路由協議中造成tcp性能降低的因素、 adhoc網路中應採取的特殊擁塞控制和差錯恢復機制，在此基礎上提出了一種採用非反饋機制的解決方案，重點對方案中的關鍵參數進行分析和模擬，分析和模擬結果表明此機制可在很大程度上提高adhoc網路中tcp的性能。
  14. The scrambling and descrambling technologies include non - disturbing frequency method, analog base band disturbing method, the radio - frequency signal disturbing method, the digital disturbing method for the analog signal and the digital signal disturbing method, etc. after the introduction a project based on the compression of the rf synchronous information is formulated

    本文綜述了目前常用的幾種主要的電視信號的加解擾技術，如非擾頻加解擾技術、模擬基帶加解擾技術、射頻信號加解擾技術、模擬信號的數字處理加解擾技術以及數字信號加解擾技術等。
  15. And at this foundation through the dispersed domine analyse the paper makes a great emphasis on the application of computer aided design and simulation, then designs a series of apfc design and simulation software. this paper takes out a set of designation and simulation on base of actual circuit. the reliable result, output voltage and inductance current which are got from this software are the same as the actual value

    本文在對一系列apfc電路設計、模擬分析方法討論比較的基礎上，著重應用離散時域法進行了計算機輔助電路設計和模擬方法的應用探索，以此為基礎設計了pfcexpert功率因數校正電路設計、模擬軟體，針對實際電路給出了整個設計和模擬全過程，通過實驗驗證了該軟體所得到的精確穩態解、瞬態輸出電壓和電感電流，與實際電路輸出基本相同，所建立的電路模型重現了電路的運行過程，反映了電路的實際工作機理。
  16. The macro model of drift region resistance was established based on the solution of poisson ’ s equations and continuity equations. by the combination of spice mos ( level = 3 ) and the macro model, the complete dddmos model was then obtained, which accords well with simulated data. by simulating and comparing different devices of different process parameters, the model is applicable for different bias regions and can be useful in the power integrated circuit research in future

    首先介紹了器件建模的基本原理及相關模擬技術，然後利用工藝模擬軟體生成器件基本結構，並對其基本特性進行了分析;分析了業內和學術界比較通用的高壓器件建模的方法，隨后在模擬實驗的基礎上著重分析了dddmos的物理特性，在求解泊松方程、連續性方程等基本方程的基礎上，建立有物理意義的漂移區電阻的宏模型;隨后結合spicemos （ level = 3 ）模型而得到完整的dddmos模型，此模型與模擬數據符合得比較好，通過對不同工藝參數的器件進行模擬比較，該模型能夠覆蓋不同的工作偏壓范圍，具有較明確的物理意義，對今後的功率集成電路的研發有一定的參考意義。
  17. The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film

    試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。
  18. The basic idea of this method is to produce particles from the posterior densities, and these weighted samples provide approximations to the densities. in this dissertation, sequential monte carlo method and its applications in communication are investigated. firstly, its basic idea, method and improved method are introduced, then induce the bound of particles, which determines the performance of the system, and the more particles are chosen, the higher computation is done, finally, a new detector based on new importance function is proposed, which deals with the joint channel estimation and detection in flat fading channels

    首先介紹了它的基本思想、基本方法、及當前研究現狀；在此基礎上推導出樣本數選擇的界，樣本數的選擇決定了系統的性能，但是若選的太多，計算復雜度也會隨之增大，因而給出這個界是十分有意義的；最後提出了一種基於新的重要函數的檢測器用來解決平坦衰落通道下的聯合通道估計和檢測問題，並通過模擬證明了我們提出的新檢測器的有效性。
  19. The content of each part follow as : in the first chapter, as start point and base of the paper, this part focuses on the basic study of definition characteristic of no, and the existing base of no - e - commerce environment ; in the second one, this part studies the theory base of no comprehensively applying the theories of core competence competent strategy and transaction cost ; chapter three studies the no from the coordination of no, and gives the structure clarification and characteristic of no firstly, at the same time, put forward the concept of virtual enterprise cluster ; based on such conclusion, studies the model of no from life cyc organization level process and value chain, and operational mode ; in chapter four, a theoretical explanation was addressed on the above structure by modeling no with game theory and graphic theory ; in the fifth chapter, on the bases of analysis of no operational risks, coordination mechanism of no was studied by individually modeling the no without core and no with core, and then put forward the solution for coordination mechanism of no ; as an important component of coordination mechanism of no, chapter six explored some basic concept of trust and importantly put forward the way of how to build trust in no, especially investigated the supporting function of valid reputation mechanism of no for the trust building, importantly an operational method on building reputation mechanism and evaluation method in no were given ; the last chapter applied the conclusion of the paper to investigate the famous trade web - sunbu. com analyzed its shortcoming and gave the advices of developing

    全文共分為七章，主要內容如下：第一章作為全文的理論出發點和基礎，圍繞網路組織的定義、特徵以及網路組織生存基礎- -電子商務環境等方面對網路組織的基本概念進行了闡述；第二章綜合運用核心能力、競爭戰略和交易費用理論對網路組織產生的理論基礎進行闡述；第三章首先從組織協調的角度對網路組織進行了研究，給出了網路組織的結構，分類和特徵，同時並給出了虛擬企業群簇；然後在此基礎上分別研究了網路組織的生命周期模型、層次模型、過程模型、價值鏈模型，以及運行模式；第四章綜合運用博弈論、圖論的相關知識，通過構建網路組織的模型，對上一章所研究的網路組織結構的形成機理給出了一種理論解釋；第五章在分析網路組織運行風險的基礎上，分別建立無盟主網路組織的博弈論模型和有盟主網路組織的博弈論模型，詳細研究了網路組織的協調機制，然後給出了網路組織協調機制的解決方案；第六章作為網路組織協調機制的重要組成部分，本章在討論了網路組織中建立信任機制的必要性的基礎上，研究了網路組織信任關系的類型，提出了在網路組織中如何建立信任機制。
  20. ( 3 ) fem basic theory of foundation pit excavation stimulation is expounded, numerical model and method of construction simulation are determinated, which includes simplification of two - dimension problem and constitutive model of soil mass i. e. constitutive model of duncan - chang hyperbola model, numerical ways of initial situ stress, stimulation of equal nodal load of foundation pit excavation, nonlinear solutions of basic equations, fem disposing of inner supporting and pre - axial force etc. further fem code of stimulation of foundation pit excavation is compiled

    闡述了基坑開挖模擬的有限元基本理論，確定計算模型及施工模擬方法。包括二維問題的簡化、土體的本構模型，即鄧肯-張雙曲線本構模型、初始地應力場的計算方法、基坑開挖等效結點荷載模擬、基本方程的非線性解法、內支撐及預加軸力的有限元處理等，並編制了模擬基坑開挖的有限元程序。
分享友人
分享到 Line

分享到臉書