擰制 的英文怎麼說
中文拼音 [nǐngzhì]
擰制
英文
turn locks-
Shipbuilding - bronze 5k screw - down check globe valves
造船.青銅制5k螺旋擰緊止回球閥Shipbuilding - bronze 16k screw - down check globe valves
造船.青銅制16k螺旋擰緊止回球閥Shipbuilding - cast iron 5k screw - down check globe valves
造船.鑄鐵制5k螺旋擰緊止回球閥Double - wall water heaters with cover to be unscrewed, of steel
帶擰卸蓋的鋼制雙壁熱水器Single - wall water heaters with cover to be unscrewed, of steel
帶擰卸蓋的鋼制單壁熱水器Combines with a concrete subject, this paper, composed of seven chapers, makes a deep analysis on theory and experiment of key bolt fastening of engine. the first chapter presents the theory of tightening technology of the available bolt the second chapter gives a narrating about tighten technology availably in survey. pointing that the nature of torque control is axis preload
本文結合一具體課題,第一章敘述了可控螺栓擰緊技術的理論,第二章綜述了可控擰緊技術,提出了扭矩控制研究的實質是控制螺栓的軸向預緊力。Unscrew the four bolts to separate the body from the bonnet and control group
擰松四個螺栓,從閥帽和控制組建之間分開閥體。( 3 ) as to the study on the organizational function, the findings are : a ) the in - service teachers and the pre - service teachers " underlying attitude towards the students are comparatively imperious than that of the prizewinners in fine - quality classroom competitions ; b ) the relationship between the prizewinners and the students are comparatively equal, but their underlying attitude towards the students is so polite that they lose the real attitude towards the students as they do in the real situation of efl classroom, c ) the prizewinners " language range seems richer than the other two kinds of teachers
( 3 )就指令語所表達的語言功能而言,實習教師和擰洶教師對沁。們兒態度較優質課教師的態度要「專制」些;然而,盡管憂質課教vllj 『 j 。 j 『生的關系較為平等,在課堂上他們給予學生更多亡由選抒的機全,但是他們對學生的態度似乎過于禮貌,從而出左了真實課堂教於, nj氣氛。Shipbuilding - bronze 5k screw - down check angle valves
造船.青銅制5k螺旋擰緊止回角閥Shipbuilding - bronze 16k screw - down check angle valves
造船.青銅制16k螺旋擰緊止回角閥Shipbuilding - cast iron 5k screw - down check angle valves
造船.鑄鐵制5k螺旋擰緊止回角閥Shipbuilding - cast iron 16k screw - down check angle valves
造船.鑄鐵制16k螺旋擰緊止回角閥Shipbuilding - cast iron 10k screw - down check angle valves
造船.鑄鐵制10k螺旋擰緊止回角閥Chapter three makes clear the importance of preload, and deals with the theories on the relationship between preload and torque, angle and extension of the bolt from various aspects
第三章由扭矩控制的實質? ?預緊力,點明了預緊力的重要性,預緊力與擰緊力矩、螺母轉角、螺栓伸長的關系,對其進行了理論方面的研究和探討。During use, if water is insufficient, you can turn off the tap, screw off the water inlet hose of controller, use water to clean the inside filter, and then reinstall it
在使用過程中,若出現水量不足時,可把水源關掉,擰開控制器進水口的軟管,用水小心清洗進水口內的過濾網,再重新裝好即可。Standard specification for " twist off " type tension control structural bolt nut washer assemblies, steel, heat treated, 120 105 ksi minimum tensile strength
120 105ksi最小抗張強度的熱處理鋼制"擰松式"張力控制結構螺栓螺母墊圈配件的標準規范The dissertation studied the control velocity of the micro robot. chapter six discussed the control with the demands of safety and human comfort when the micro
論文第六章針對機器人運行的平穩性和人體的舒適性要求,提出了機器人的阻抗擰制方案。In chapter four, the parameter in the bolt fastening process is set down and the controlling methods and comparison is analyzed
第四章討論了螺紋裝配過程參數的設定和螺栓擰緊的控制方法及比較,並對擰緊控制方法的選用進行了分析。The method of torque - angle is adopted as the control method of the intelligent screw tightening machine on the basis of analyzing the excellence and deficiency of all kinds of control methods and taking practical situation into account. secondly, the design of the machinery of the tightening machine is explained in detail, almost all parts of the structure principle diagrams are given and an introduction of function of each part in the diagram is made concisely
文章首先對螺紋擰緊的控制方法進行了探討,在分析各種方法優缺點和結合實際情況的基礎上採用扭矩轉角法為螺紋自動擰緊機的控制方法。然後,文章詳細地介紹了擰緊機的機構部分設計,給出了擰緊機的各部分的結構原理圖,並對原理圖中的各個環節的功能作了簡要介紹。Shipbuilding - cast iron 10k screw - down check globe valves
造船.鑄鐵制10k螺旋擰緊止回球閥分享友人