擺動機構 的英文怎麼說

中文拼音 [bǎidòngjīgòu]
擺動機構 英文
swing mechanism
  • 擺 : Ⅰ動詞1 （安放; 排列） put; arrange; set in order 2 （顯示; 炫耀） display; show off; put on; assu...
  • 機 : machineengine
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 擺動 : 1 （搖擺） swing; sway; oscillate; pendulate; waggle; wobble; vibrate; wiggle 2 [機械工程] jiggin...
  • 機構 : 1 [機械工程] （機械的內部構造或一個單元） mechanism 2 （機關; 團體） organ; organization; institu...
  1. A single are needle sewing blind stitching, a sewing thread hook taking up thread, forming type 103 single thread chain stitch

    單弧針擺刺料、擺動線鉤勾線，形成103型單線鏈式線跡。採用圓筒式機構，適合襪子、手套、羊毛衫、褲管口等暗縫。
  2. By taking advantage of computer technology the main parts of the reducer - epicycloid groove, hypocycloid groove, steel ball and output mechanism are shown and emulated. the motion of the drive is also demonstrated. the paper mainly concludes the following works : at first, the meshing efficiency of the drive is studied and analyzed in theory according to the constituted construction and the drive principles

    在對其傳動原理及結構進行分析的基礎上，對該傳動的嚙合效率進行了深入研究，並針對該傳動的整體尺寸進行了參數模糊可靠性優化，進而利用計算機技術，對該傳動的主要零件? ?內、外擺線盤和等速輸出機構進行了三維建模模擬，演示了該傳動的運動情況。
  3. It is applied to sorts of locomotive engine, in course of revolving of crank and connecting rod mechanism, there are revolving of the crankshaft, swinging of the connecting rod and reciprocating motion, so its motion state is complex, and periodic unbalanced force, by a few components, is great

    曲柄連桿機構在高速運轉過程中，有曲軸的轉動、連桿的擺動及活塞的往復運動，其運動狀態復雜，各個部件所產生的周期性不平衡慣性力大，是引起發動機振動的主要原因。
  4. This article uses advanced cad / cae software - - - ug, adams and ansys to build the integrated system platform based on theory of dynamics of multibody system for the purpose of resolving the engineering problems of general retarder design, and analyses the performance of xw - 8175 - 11 planet - cycloid retarder

    本論文針對行星齒輪減速機構設計中存在的問題並根據實際工程需要，在多體動力學理論基礎上，利用cad cae軟體ug 、 adams以及ansys構建了集成的系統平臺，並在此基礎上，對xw - 8175 -型擺線針輪減速機構進行了性能模擬。
  5. Based on above distributed simulation software of multibody system dynamics, three examples of distributed sensibility analysis, double pendulum system, planar four - bar mechanical system and slider - crank system, are numerically dealt with, the results of which indicates that the methods raised in this paper are correct

    基於所完成的系統運動學分散式模擬軟體，實現了雙擺機構、平面四連桿機構、曲柄滑塊機構的分散式靈敏度分析算例，驗證了本文方法的正確性。
  6. By means of feature analysis on the one - way dividing mechanism of butter fly - hoard oscillation, the influence on the characteristics affected by relevant dimensions of every dividing element was explained in this paper

    通過對蝶板擺動單向分度機構的特性分析，說明了各分度元件的有關尺寸對該分度機構特性的影響。
  7. Owing to the advantages of air - pressure transmission, the dividing mechanism driven by the reciprocal linear movement of pneumatic cylinder has been applied broader and broader the one - way dividing mechanism of butterfly - hoard oscillation was one of the mechanisms among them

    摘要由於氣壓傳動的優點，由氣缸往復直線移動驅動的分度機構應用越來越廣，蝶板擺動單向分度機構就是其中之一。
  8. The bogie is feasible, in which the primary suspension is flexible, and the tilting mechanism of passenger car is composed of four swing bars and an electromechanical actuator

    傾擺機構採用四擺桿機構加機電式作動器，為簧間擺模式。
  9. For rotary axes can be made less expensive, easier and more compact than a linear guide at the same precision level, a rotary arm that carries a diamond tool combined with a fast tool servo are used to replace the straight lines

    由於旋轉抽與同等精度的直線導軌相比，具有製造難度小、成本低及結構緊湊等優點，所以採用具有快速伺服機構的金剛石刀架擺臂代替直線導軌進給運動方式。
  10. Discussinng the synthesis of cam - five linked mechanism for the given locus, and giving the detailed formulas by an example

    摘要對實現預定軌跡的擺動從動件盤形凸輪五桿機構的設計進行探討，並通過實例給出具體的解析設計公式和步驟。
  11. Aimed at the equal - diameter cam mechanism with follower of planar movement, and according to two conditions of existing meaningful solution of the mechanism and of ensuring transmission angle of output swinging rod, the value selection ranges of cam motion angle, of swinging angle of out - put swinging rod and of its primary installation angle were analyzed and determined, and then proceed to plot the region graph of selectable value for motion angle of cam and swinging angle of swinging rod, thus provided convenience for the design and employment of that mechanism

    摘要針對平面運動從動件等徑凸輪機構，根據機構存在有意義解和保證輸出擺桿傳動角兩個條件，分析並確定了凸輪運動角、輸出擺桿擺角及其初始安裝角的取值范圍，進而繪制了凸輪運動角與擺桿擺角的可選值域圖，為該機構的設計與使用提供了方便。
  12. On the basis of the known actual contour equation of cam in the disk typed cam mechanism with swinging oblique bottomed follower, this paper expounded another method for determining inversely the track equation of cutter center and the motion law of follower, and three key techniques in numerical inverse seeking were solved successfully by adopting the method of curve matching

    摘要根據已知擺動斜底從動件盤狀凸輪機構的凸輪實際廓線方程，闡述了反求確定刀具中心軌跡方程和從動件運動規律的另一種方法，並採用曲線擬合等方法成功地解決了數值反求中的3個關鍵技術。
  13. ( 5 ) the direct calibration method of heavy block calibration is first presented and realized. the structures and controlling circuits of automatic adjusting pendulum and automatic calibration are designed

    （ 5 ）首次提出並實現了重塊標定的直接標定方法，設計了自動調擺和自動標定機構和控制電路。
  14. Abstract : the paper shows the relative deformation function of the cam mechanism with a roller follower as a linear time - invariant system, and gives the detail about the response limitation for the dynamic design and modification of cam mechanisms. an example demonstrates this approach can improve the flexible cam mechanisms

    文摘:以滾子從動件平面凸輪機構為分析對象，提出了相對變形函數這一新概念，並從理論上對其進行了研究，最後藉助於一凸輪機構在不同參數下其擺臂最大相對變形量的數值計算過程與結果，闡述了基於該理論的凸輪機構動態設計與修改的具體實現步驟與方法。
  15. 2. the splitting method, enclosed planetary transmission sketch method and structure sketch method are used to deduce the transmission ratio formulas on several structures of the single - stage and double - stage spatial - cycloid - ball gearing respectively. further more, the simplified calculating formulas on one - tooth - difference and two - tooth - difference spatial - cycloid - ball gearing are given

    2 、分別運用拆分法，封閉行星機構的傳動簡圖和結構簡圖推導出單級和雙級的多種結構的傳動比公式，並給出一齒差、二齒差球面擺線鋼球傳動機構減速比的簡化計算公式。
  16. It is indicated through the analysis of assistant steering mechanism of the farm transporter model fr1608 that within th e rang e of standard swinging of the pitman arm, the design rod structure satisfies the requirement of optimum pressure angle

    對fr1608運輸車轉向助力機構的分析結果表明，在轉向器轉向垂臂的標準擺動范圍內，設計參數滿足最佳壓力角要求。
  17. Utilizing the dynamics analytical software adams of mechanical system, the virtual prototyping model of sway downward paper feeding mechanical was established and a simulation analysis was carried out

    摘要利用機械繫統動力學分析軟體adams ，建立了下擺式遞紙機構的虛擬樣機模型，並進行了模擬分析。
  18. The vibration plate is a rice seedling feeding device and the most important working component in the whole machine

    排秧盤是振動式擺秧機缽苗輸送機構，也是最主要的工作部件之一。
  19. Digital displayer, pleasing massage on the neck, rollers moving up and down along the back, multiple modes for intelligent controlling, soft artificial sponge inside, conveying structures without noise, arc wheels massaging up and down integrated with knocking and vibration

    屏面數碼顯示，舒適的頸部按摩，上下式滾背按摩及多種智能控制模式，柔性人造海綿內膽，靜音傳動機構，其將弧擺上下移動和叩擊振動有機相結合。
  20. In accordance with dynamic characteristics of swing movable teeth drive, the torsional vibration dynamic model of swing movable teeth drive is developed and the vibration equation of the vibration system is established for the first time

    針對擺動活齒傳動機構的動力學特點，首次建立了擺動活齒傳動系統的扭轉振動動力學模型，導出了系統扭轉振動的動力學方程，並對系統動力學響應進行了求解。
分享友人
分享到 Line

分享到臉書