支承板 的英文怎麼說
中文拼音 [zhīchéngbǎn]
支承板
英文
back plate-
Lathe spindle noses and back plates. type bayonet
車床主軸頭部和支承板.卡口型The bents supporting the four continuous 工 beam plate girders have a cross section shaped like a box.
構架支承著四片工字型板梁，構架的截面為箱型。Place all testing devices on the testing machine in the following order : bearing plate, emery cloth ( with the granular surface facing upward ), the resilient pad to be tested, emery cloth ( with the granular surface facing downward ), short rail ( make sure the short rail is placed within the action area of the resilient pad to be tested )
把試驗裝置安放在試驗機上，安放順序為：支承鋼板、砂布（有砂粒面朝上） 、被測彈性墊層、砂布（有砂粒面朝下） 、短鋼軌（確保短鋼軌放置在被測軌下彈性墊層起作用的區域） 。The horizontal bed is the foundation member which supports the headstock, tailstock, and carriage.
臥式床身是基礎構件，用來支承床頭箱、尾座和拖板。With the car upside-down, the ball forces the plunger to seat against the guide plate.
當汽車傾倒時，滾珠迫使柱塞落在支承板上。The parts and units of jigs and fixtures. supporting plate
機床夾具零件及部件.支承板Beam type gas injection packing support plate
梁型氣體噴射式填料支承板Injection mould for plastic large - size mould bases - support plates
塑料注射模大型模架支承板Four sides supported plate
四邊支承板12Two sides supported plate
兩邊支承板12United solution method on four edges supported plate bending with boundary displacements
支座位移作用下四邊支承矩形彈性薄板彎曲統一求解方法Tubular heat exchangers ; tube pitches, diameter of bores in tube sheets, baffles and support plates
管式熱交換器.管心距管薄板的鉆孔直徑.擋板和支承Rough surface in front and back plate
前面與後面支承板表面粗糙。The work in this thesis mainly includes following parts : 1. as for box girder cross section, the three - bar stimulation method under typical loads and supports has been introduced. the force and stress formulae for flanges have been derived from the three - bar method. by reasonable simplification for multi - cell box girder, the three - bar method has been applied in multi - cell box girder ' s shear lag analysis
對于箱形截面主梁，本文介紹了三桿比擬法上、下翼板中比擬桿的計算公式，以及在典型荷載和支承的情況下翼板內各桿的應力計算公式，並對多箱式主梁截面進行合理簡化，使三桿比擬法應用於多室箱梁的剪力滯分析。These designing parameters include stiffness of epicyclical bearings, synthetic meshing stiffness of gears, stiffness of supporting bearing of out put shaft, mass of inner rack, meshing angle of gears, distance between inputting shaft and supporting shaft and input speed etc. according to these analyses, the possible way for improving the dynamic function of three - ring transmission may be put forward
這些設計參數包括：行星軸承剛度、齒輪綜合嚙合剛度、輸出軸支承軸承剛度、內齒板質量、齒輪嚙合角、輸入軸和支承軸間距及輸入轉速等，根據這些分析，可以提出改善三環傳動動態性能的可能途徑。Laminated springs ; spring link washer bearing plates for spring suspension
疊層彈簧.彈簧懸掛的彈簧連接墊圈支承板Insulators and fittings for overhead lines. metal fittings. back plates pf 59 and pf 70
架空線路用絕緣子和配件.金屬配件.支承板pf 59和pf 70Excavations and trenches - slopes, planking and strutting, breadths of working spaces
坑道和溝渠.工作空間的坡度鋪板和支承柱寬度Generally, the skew bridge ' s calculation theories can be divided into three types : the category 1 is the plank theories method, such as the finite difference method, the finite element method and the finite strip method, etc ; the category 2 is the beam theories, such as the grid beam theories, the general grid theories, the rigid cross - beam method, the elastically - supported continuous beam method and the bar system analytical method, etc ; the category 3 is the practical method, such as the g - m revising method, the grid - beam simple method and ghali form coefficient method, etc
目前關于斜梁橋的計算理論和方法概括起來，大致可以分為三類：第一類為板理論方法，如有限差分法、變分法、有限單元法、有限條法等；第二類為梁理論法，如格構梁理論、一般格構理論、剛性橫梁法、彈性支承連續法、桿件結構的分析方法；第三類為實用計演算法，荷載橫向分佈的計算方法如g ? m修正法、格構梁的簡易法、 ghali表格系數法等。( 3 ) a large computer program, named 3dplate, is developed with fortran powerstation. with 3dplate, 6 simply supported square plates. 5 clamped rectangular plates and 1 corner - supported plate are analyzed
（ 3 ）用fortran語言編制了大型的計算機程序3dplate ，並對6塊的四邊簡支方板、 5塊四邊固支矩形板和1塊四角支承板進行了計算分析。分享友人