收縮接縫 的英文怎麼說

中文拼音 [shōusuōjiēféng]
收縮接縫 英文
contraction joint
  • 收 : Ⅰ動詞1 （把攤開的或分散的事物聚集、合攏） put away; take in 2 （收取） collect 3 （收割） harvest...
  • 縮 : 縮構詞成分。
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 縫 : 縫名詞1. （接合處） seam 2. （縫隙） crack; crevice; fissure; slit
  • 收縮 : 1 （由大變小; 由長變短） contract; shrink 2 （緊縮） concentrate one s forces; draw back 3 take u...
  • 接縫 : seam; jugum; joint; kiss; unwelded joint接縫刨 jointer; 接縫構造 seam construction; 接縫灌漿 joint grouting
  1. Some other defects in castings are well - defined cracks and hot tears that develop during solidification, under combination of stress concentration from uneven contraction and the metal ' s low strength at near - melting temperatures

    鑄件內部的其它一些缺點是，凝固過程中，在不均勻收縮造成的應力集中和接近熔點溫度下金屬的低強度的綜合作用下，出現的清晰裂縫和熱撕裂。
  2. Perhaps it was with the hope of narrowing it that she yielded to his persuasions to go to night school and business college and to have herself gowned by a wonderful dressmaker who charged outrageous prices

    也許是為了縮小距離，她接受了他的建議去上夜校，上商業學院，還請了一個了不起的女衣裁縫給她做衣服，那裁縫收費高得嚇人。
  3. In the light of the problems during the tank bottom plate welding of 150000 m ^ 3 double - pontoon floating roof oil tank, the paper analyzes the deformation cause of tank wall shell in welding

    摘要分析了15 10 ^ 4立方公尺雙盤浮頂油罐罐底板焊接過程中出現的問題，提出焊縫收縮使得對接間隙變小是引起邊緣板變形的主要原因。
  4. Welding position : if the configuration collocation of weld is symmetry and the welding sequence is reasonable, the longitudinal contraction and transverse lateral contraction deformation are usually produced, incontrast, the bending deformation is usually produced

    焊接位置：如果焊縫在結構布置對稱，焊接順序合理時，則主要產生縱向收縮和橫向收縮變形，反之，則要發生彎曲變形。
  5. Adhesives and grouts for tiles - part 4 : determination of shrinkage ; german version en 12808 - 4 : 2001

    瓷磚膠粘劑和接縫灰漿.第4部分:收縮量測定
  6. Effect of load and indirect load such as shrinkage, creep was often taken into account separately to satisfy the requirement of crack width in reinforcement design of large area prestressed concrete frame structures

    摘要大面積預應力混凝土框架結構設計時一般將直接荷載產生的作用與溫度、混凝土收縮產生的作用分開計算，分別配筋以滿足裂縫控制的要求，這種做法不盡合理。
  7. The change of moisture distribution is concentrated on the surface layer concrete, which is very thin. however, the change inside the concrete is very slight. this unbalanced development of moisture distribution causes large shrinkage stress in the layer concrete and then leads to crack

    混凝土濕度變化主要集中於較薄的表層混凝土內，內部濕度場變化極微，這種濕度發展變化的不均衡使得表層混凝土內產生較大的收縮應力，將直接導致裂縫的產生。
分享友人
分享到 Line

分享到臉書