故障頻度 的英文怎麼說

中文拼音 [gùzhàngbīndù]
故障頻度 英文
frequency of damage
  • 故 : Ⅰ名詞1 （事故） event; incident; happening; accident 2 （原因） cause; reason 3 （朋友; 友情） fr...
  • 障 : Ⅰ動詞（阻隔; 遮擋） block; hinder; obstruct Ⅱ名詞（遮擋物） barrier; block; obstacle
  • 頻 : Ⅰ形容詞（次數多） frequent Ⅱ副詞（屢次） frequently; repeatedly Ⅲ名詞1 [物理學] （物體每秒鐘振動...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 故障 : hitch; breakdown; stoppage; fault; faulting; accident; blunder; bug; conk; failure; impairment; i...
  1. In the first part of the paper, the development of motor control system fault diagnosis theory is summarized. on the basis of the analysis of the characteristics of wavelet, the theory is discussed and the definition of the singularity is given. because of the localization property of wavelet transform, wavelet analysis can be used to detect the characteristics of the singularity from the signal and intermittence fault problems lying in the motor under test

    著重介紹了小波分析在電機控制系統故障診斷中的應用，根據小波理論在時域和頻域良好的局部化性質，討論了利用小波變換來檢測信號的奇異特徵的原理，給出了小波變換對信號奇異性特徵檢測的方法，針對實際應用，對小波基函數選取及小波分解尺度進行了探討。
  2. On the other hand, by meticulous diagnosis functions, such as signature analysis, trend analysis, spectrum analysis, the fault classification, position, severity and trend about the high - pressure getting rid of squama while running can be discovered and forecasted

    另外，該系統的精密診斷功能，包括歷史數據回放分析、趨勢分析、時域分析、頻譜分析，能對水泵的故障類型、部位、嚴重程度以及發展趨勢進行分析和預測。
  3. This method of diesel engine fault diagnosis is feasible theoretically. while the fault diagnosis system using this method is rare, just because the crankshaft instantaneous angular acceleration measurement is demanding, such as, good frequency response, high precision

    這種柴油機故障診斷的方法在理論上是可行的，但目前這種成型的系統不多，究其原因是測量曲軸的瞬時角加速度需要系統具有良好的頻率響應特性與高精度。
  4. Scale choosing based on spectrum analysis in a novel wavelet principle for fault line selection

    小波故障選線新原理中基於頻譜分析的尺度選擇
  5. What is mainly discussed in this dissertation is as follows : the fault mechanism and vibration frequency feature of hydroelectric vibration are analyzed, induced and reorganized. the select and placement of detecting positions of parameters such as vibration, swing and pressure pulsation are researched, and the corresponding sensors are selected to monitor

    本文主要進行了以下工作：分析、歸納和整理了水電機組振動的故障機理和振動頻率特徵，對機組的振動、擺度和壓力脈動測點進行了選擇和布置，並選用相應傳感器進行監測。
  6. Assisted with the sensitivity of the linear analog circuits, the feasibility of parametric faults detection was analyzed through the maximum fault errors acquired at the sensitive frequencies, a stimulation matrix and its stimulation expression were put forward on the test points information

    摘要從線性模擬電路靈敏度的概念入手，分析了通過獲取敏感頻點激勵下的最大故障誤差來檢測電路參數故障的可能性，提出了一種針對測試頻率和測點信息的激勵矩陣。
  7. Therefore, research on integrated process control system, which includes such roles as control, monitoring, diagnosis, proves to have important theoretical and practical value. fault diagnosis, provides scientific methodology to detect and diagnose system exception, and find out fault source, frequency, severity, tendency etc., so as to take timely and effective solution

    故障診斷就是監視控制系統進行故障檢測與診斷，並對故障的原因、故障頻率、故障的危害程度及趨勢預測等內容進行分析判斷，為確診故障點、及早採取維修、防護等補救措施提供科學的決策依據。
  8. Based on the " research on the new method for rotating machine faults diagnosis based on independent component analysis " ( national nature science fund project, no : 50205025 ) and " study on the new method of corba - based distributed calculation tactics construction in remote condition monitoring and diagnosis " ( zhejiang province nature science fund project, no : 501061 ), this paper aimed to the rotating machinery faults diagnosis oriented time - frequency analysis. the emd - based basic theories and methods were studied ; to weaken the emd method ' s end effect, some new data extention means were proposed ; to improve the emd method ' s precision and efficiency, some new algorithms were proposed ; the emd based time - frequency analysis software was designed and developed ; a experiment system at the base of rotor test bed was built to study the ro tor faults diagnosis using the new time - frequency analysis method, then studed several typical faults

    本文結合「基於獨立分量分析的旋轉機械故障診斷新方法的研究」國家自然科學基金項目（ 50205025 ）和「基於corba分佈計算策略構建遠程監診的新方法研究」省自然科學基金項目（ 501061 ） ，以面向大型旋轉機械故障診斷的時頻分析為目標，研究了該方法的基本原理和演算法：針對其端點效應等不足，提出了新的數據延拓技術；針對emd演算法的精度和速度上的不足，提出了新的改進演算法；設計和開發了基於emd時頻分析的軟體系統；以模擬轉子實驗臺為基礎構建了實驗系統，並進行了實驗研究。
  9. In the first session the fans vibration on - line monitoring system is realized with vc language, also compile auto power spectrum density function, cross power spectrum density function, autocorrelation function and cross correlation function etc spectral analysis function to carry through simple offline fault diagnosis

    首先用穩定性強、擴展性好的vc + +語言開發了通風機振動在線監測系統，並編寫了自功率譜密度函數、互功率譜密度函數、自相關函數和互相關函數等頻譜分析函數來進行簡單的離線故障診斷。
  10. When this fault is cutted off and the breaker is reclosed, this scheme ca n ' t start by mistake. the availability of this scheme is proved with matlab test. the single phase high - impedance grounding fault is settled properly

    Matlab模擬分析證明了該方案耐受過渡電阻的能力強，在故障切除和重合閘時不會因出現的暫態信號而誤啟動，不受系統振蕩、頻率偏差的影響，克服了常規保護靈敏度不足的缺點，較好地解決了單相高阻接地故障的難題。
  11. Plenty of experiments show the real, imaginary, module and angle of wavelet transform can accurately choose the fault line and precisely identify the high frequency of transient signals

    通過大量的實驗，表明利用小波變換后的實部、虛部、模值以及相角可以準確的給出故障線路並高精度的提取故障信號的暫態高頻分量。
  12. The establishment of gear fault data warehouse the paper studies several gear cases in drive lab of wuhan university of science and technology. the signal of normal gear pair, the one has been worn seriously, the one which has circular pitch error and the one whose pinion has a ruptured tooth is acquired independently. after fft transformation, the amplitude values of 0 - 0. 4 multiple engage frequency, 0. 4 - 0. 5 multiple engage frequency, 0. 5 - 1 multiple engage frequency, 1 multiple engage frequency, 2 multiple engage frequency, 3 multiple engage frequency, 4 multiple engage frequency and greater then 4 multiple engage frequency of every signal are obtained respectively

    論文主要完成下列內容: 1 .齒輪故障數據倉庫的建立以武漢科技大學傳動實驗室的若干臺齒輪箱為研究對象，分別採集正常齒輪副、磨損嚴重的齒輪副、有周節誤差的齒輪副和小齒輪有一個斷齒的齒輪副的振動加速度信號，經過fft變換，分別得到每個信號的0 ~ 0 . 4倍嚙合頻率、 0 . 4 ~ 0 . 5倍嚙合頻率、 0 . 5 ~ 1倍嚙合頻率、 1倍嚙合頻率、 2倍嚙合頻率、 3倍嚙合頻率、 4倍嚙合頻率和大於4倍嚙合頻率幅值。
  13. This unit is particularly designed for monitoring 400v feeder with backup automatic switch. it could accurately measure and calculate : voltage, current, frequency, active power, reactive power, power factor and energy. when bus gets into trouble, it can perform the function of automatic switching to backup power supply

    該單元是特別針對400v饋線備自投而設計的，它具有測量母線的電壓、電流、頻率、有功功率、無功功率、功率因數以及有功電度、無功電度等電參數的功能；當母線出現故障（過壓或欠壓）時，能夠完成兩組母線的自動投切，即備自投的功能。
  14. It mainly includes following aspects : in this paper, firstly implication of wavelet analysis in signal harmonic component extraction is presented in detail, and on this foundation signal given frequency band component extraction method is proposed. then we investigate frequency aliasing phenomenon, reason why frequency aliasing phenomenon is easy happened when wavelet is implied in field of motor fault diagnosis, and frequency bands where frequency aliasing phenomenon is easer happened, and put forward approved morlet wavelet analysis method which can effectively alleviates frequency aliasing phenomenon. third we set up vibration signal detected system, design experiments to obtain three groups of fault signals : eccentricity fault, mixed fault of eccentricity plus mild rub, mixed fault of eccentricity plus moderate rub, and process these data using analysis method proposed in this paper

    首先對論文的選題以及相關背景進行了探討，並對相關的小波基礎理論進行了闡述，主要針對感應電動機的偏心故障和偏心+碰摩復合故障形式及相關的應用演算法進行了詳細探討，主要工作內容包括下面幾個方面:在論文中，首先對小波分析在信號的諧波分量提取中的應用進行了研究，在此基礎上，提出了信號的特定頻帶成分的提取方法;研究了小波分析的頻域混疊現象，探討了小波分析應用於電機故障診斷領域時易發生頻域混疊現象的原因，以及混疊現象較易發生的頻帶，提出了可以有效減輕頻域混疊現象的改進的morlet小波分析方法;搭建了振動信號檢測系統，設計實驗採集得到三組故障數據:偏心故障，偏心+輕微碰摩復合故障，偏心+中度碰摩復合故障，並對這些數據應用本文提出的分析方法進行信號處理，提取出的特徵參數可有效區分這兩種故障形式;研究了基於matlab和labview的混合編程方法，完成了電機故障檢測系統的軟體開發。
  15. Because direct torque control requires very high performance of real - time, the popular microcomputer core dsp is used as controller in the design of hardware. its high speed of running is suitable for the experiment. in the main circuit, there is a highly integrated power element : ipm as inverter, which includes seven igbt, has high switch frequency and fault diagnosis function

    在本控制系統的具體實現上，由於直接轉矩控制對實時性要求很高，因此在硬體方面，採用了目前比較流行的數字信號處理器（ dsp ）作為系統的控制器，其處理速度高的特點正好符合本實驗的需要：在主電路中，本系統使用了集成度高的功率器件：智能功率模塊（ ipm ） ，作為逆變環節，其集成了七個igbt ，實現了高開關頻率逆變以及故障診斷的功能，從而使控制系統的體積大大縮小、控制更加靈活。
  16. Due to the direct torque control requires very high performance of real - time, the popular microcomputer core dsp is used as controller in the design of hardware. its high speed of running is suitable to the experiment. in the main circuit, there is a highly integrated power element : ipm as inverter, which includes seven igbt, has high switch frequency and fault diagnosis function

    在本控制系統的具體實現上，由於直接轉矩控制對實時性要求很高，因此在硬體方面，本課題採用了目前比較流行的數字信號處理器（ dsp ）作為本實驗的控制器，其處理速度高的特點正好符合本實驗的需要；在主電路中，本系統使用了集成度高的功率器件：智能功率模塊（ ipm ） ，作為逆變環節，其集成了七個igbt ，實現了高開關頻率逆變以及故障診斷的功能，從而使控制系統的體積大大縮小、控制更加靈活。
  17. The feasibility of using mallat algorithm to extract the feature component of rotor bar faults is discussed, and we find that mallat algorithm is not suitable for rotor bar faults detection because of the similar representations of the fault and the normal signals

    分析了應用mallat小波變換快速演算法提取轉子斷條故障特徵的可行性，指出由於故障信號與正常信號在時頻域上的表現非常接近，僅使用基於頻帶劃分的多解析度分析方法的mallat演算法難以提取出明顯的轉子斷條特徵量。
  18. As to the video signal, alarm signal, control signal, are all weak electricity signal, exceedingly easily be subjected to the jam, in case the power supply system does not steady, wave propag ation is greatly, the harmonic content of power source overtops, the veins wave factors are great unduly, and even power source equipment breakdown, outputting abnormal, will be about to affect the video signal image effect, and dependability cuts downs to the security and alarming system. we adopt fast fu lye ' s mutation rule - fft alternatives, by the way of carrying fft alternatives to the local junction circuit, regulated power supply, ups ' s power source, and switch power source, thereby diagnose every degree harmonious wave content of power souse, and abnormal coefficient, compared to the normal working situation. thereby diagnose out the working condition of the regulated power supply, ups ' s power source, and switch power source

    如果有供電系統不穩定、波動大，電源的諧波含量過高，紋波系數過大，乃至電源設備損壞、輸出異常等情況出現，將會嚴重影響視頻信號的圖像效果，大大降低防盜系統的穩定性和可靠性，我們採用快速傅利葉變換原理，即fft變換，通過對市電、穩壓電源、 ups電源、開關電源等的電壓信號進行fft變換，從而得出信號中各次諧波的含量及信號畸變系數，並將其與正常工況下的參數進行對比，從而進一步診斷出穩壓電源、 ups電源、開關電源等設備的運行狀況；組成監控系統的設備長期處于工作狀態，往往由於設備散熱條件不好、設備老化故障等原因導致設備表面溫度過高，從而影響設備的正常運行，降低設備的使用壽命。
  19. Abstract : in order to process signal in depth and to extract the fault feature from original signal in machinery diagnosis ， the graphical display algorithm that can keep the data length of wavelet transform results the same as that of original signal is used. the fault diagnosis of a bend axial piston pump via b - spline wavelet that has linear phase is provided. the results of study demonstrate that the new method has excellent feature and the weak fault signal can be extracted from the strong vibration background of the pump

    文摘:採用具有線性相位的b樣條小波，應用圖形顯示演算法並結合小波變換快速演算法將信號分解到不同的頻帶上，且分解結果和原信號長度保持一致，可對信號進行深層次的處理，克服了傳統的信號處理方法不易提取微弱信息的不足.通過對礦用斜軸式柱塞泵振動信號的分析，分離出了配流副磨損、球鉸松動、缸體及泵軸支撐軸承的故障特徵，為液壓泵的故障診斷提供了依據，並為信噪分離、微弱信號提取及設備的早期故障診斷提供了一條有效途徑
  20. This thesis discussed approaches of fault diagnosis based on the sensitivity analysis which is a new test method of analog circuits. main objects are described as follows : first, there exists a problem which the existence of solutions can not intuitively be predicted by choosing test frequency in the first - order sensitivity method on fault diagnosis

    在此理論基礎上，本文從以下兩個方面進行嘗試:首先，一階靈敏度故障診斷方法存在這樣一個問題，即測試頻率的選擇不能直觀地對故障診斷方程解的存在性進行預分析。
分享友人
分享到 Line

分享到臉書