敷層材料 的英文怎麼說

中文拼音 [fūcéngcáiliào]
敷層材料 英文
coating material
  • 敷 : Ⅰ動詞1. （搽上; 塗上） apply 2. （鋪開; 擺開） spread; lay out 3. （夠; 足） be sufficient for Ⅱ名詞（姓氏） a surname
  • 層 : i 量詞1 （用於重疊、積累的東西 如樓層、階層、地層） storey; tier; stratum 2 （用於可以分項分步的...
  • 材 : 名詞1 （木料） timber 2 （泛指可以直接製成成品的東西; 材料） material 3 （供寫作或參考的資料） ma...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 材料 : 1. （原料） material 2. （資料） data; material 3. （適于做某種事的人才） makings; stuff
  1. The research results show that, from the viewpoint of second phase morphologies, there exist quite differences between the grain - type materials ( such as wc / bcu brazing deposit material, wrs1000 and 1zt tungsten carbide strengthening overlaying material, as well as the wear - resistant material of polymer adhesive coating etc. ), and the aggregation - type as well as dispersion - type ones ( such as zg35simn, wrd - 1 and khc - k2 depositing material ) in the wear - resistance and sand slurry abrasion mechanism. the sand slurry abrasion mechanisms are brought forward, of new wear - resistant materials with the features of grain - type second phase morphologies

    研究發現，與聚合型、彌散型第二相的材料（如zg35simn 、 wrd ? 1和khc ? k2熔敷材料等）相比，顆粒型第二相的材料（如wc bcu釬焊熔敷耐磨材料、 wrs1000型耐磨材料、 1zt碳化鎢顆粒增強熔敷材料及ktc ? 1耐磨膠粘塗層材料等）在耐磨性能和磨損機理等方面均有不同，總結提出了以「顆粒型第二相」為特徵的耐磨新材料泥沙磨損機理。
  2. Based on the technical requirements of manufacture, application and repair of the pump shell and cutter piece of the cutterhead pipeline dredge, put forward are the re - manufacture three principles on easily damaged workpieces of dredge engineering. with the inter - clamped structures on the pump liners, the gradient wear - resisting design on the cutter piece, and the new techniques in the process of re - manufacture, new wear - resistant materials, including high - cr alloy, overlaying and brazing deposits, and polymer adhesive coatings have been successfully applied to the re - manufacture dredge pump shell and cutter piece. the application results show that their wear - resistant lifetimes and the dredging profits have been increased remarkably

    根據絞吸挖泥船泥泵絞刀的製造、使用和修復性能要求，提出了疏浚工程易損件再製造三原則；採用泥泵內襯互鎖結構、絞刀梯度化耐磨設計和工藝再製造新技術，將高鉻合金耐磨材料、熔敷耐磨材料及其復合材料和高分子耐磨膠粘塗層材料成功地應用於再製造泥泵殼和絞刀片上，顯著提高了泥泵殼和絞刀的耐磨壽命和挖泥船的疏浚效益。
  3. Secondly, the two - dimensional hotibc was applied to the anisotropic coated bor. solutions for bistatic rcs based on a planar hotibc solution were compared to the mom solution or the mie series solution in isotropic case. accuracy and limitations of hotibc imposed by the finite radii of curvature on the bor such as sphere, and discontinues surface curvature such as cone - sphere were investigated

    計算過程和結果與矩量法進行比較，討論了高階張量阻抗邊界條件在表面曲率半徑連續和不連續的三維目標上的應用精度和應用條件； 6 、給出多層介質塗敷平面、球面和半球面結構雷達吸波材料優化設計的統一表達式。
分享友人
分享到 Line

分享到臉書