數位板鍵 的英文怎麼說

中文拼音 [shǔwèibǎnjiàn]
數位板鍵 英文
expresskeys
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 鍵 : 名詞1 [機械工程] （使軸與齒輪、皮帶輪等連接並固定在一起的零件） key 2 [書面語] （插門的金屬棍子）...
  • 數位 : numerical digit; digit; place; digit position
  1. Main control introduce 4 - digital numeral display and 4 - digital clavier, operation is convenience and terse 、 password egis is on the safe side

    主控制板採用4位數碼顯示， 4位鍵盤操作，操作方便簡潔；密碼保護，安全可靠。
  2. In the hardware design, the paper completes modules ’ design like outside memory, patulous a / d, patulous d / a, rs232 communication, ecan communication, led control, keyboard control, distant control, emulation, reset, logic voltage switch, dsp supply power regulate and ac - dc power circuit, as well as room layout design like anterior panel, back panel etc. and dsp transfers data with peripheral equipments except outside memory using serial ports. besides, the whole circuit is configured in interrupt response. thus, it can meet system demand as well as take full advantage of tms320f2812 ’ s hardware resource. in the software design, the paper finishs programs like the interface programms intercommunicates with people, the distant control program, ad and da modules ’ control program, in addition, the paper select the velocity and acceleration state - feedback algorithm and is written in the program. the software design uses dsp integrate exploiting environment named ccs2. 2 of ti inc. as software instrument, and programs with the combination of c language and assembly language. moreover, in order to maintenance or modify the software expediently and shorten software ’ s exploitation time, the design adopt software modularization technique. finally, some air cylinder experiments are carried out to proved that the pneumatic controller is very practical

    在硬體設計中，本文完成了片外存儲器擴展、 a / d擴展、 d / a擴展、 rs232通信介面、 ecan通信總線介面、液晶顯示控制、鍵盤控制、遠程控制、模擬、復位、邏輯電平轉換、 dsp工作電源校正電路和ac - dc電源等模塊設計以及控制器前面板、後面板等的空間布局設計。其中dsp與除外部存儲器的外圍設備之間的數據傳送全部採用串口通信，同時系統電路配置成中斷響應方式，這樣既滿足了系統要求，又充分利用了tms320f2812的硬體資源。在軟體設計中，本文完成了人機界面功能模塊、遠程控制模塊、 ad擴展模塊、 da擴展模塊、速度和加速度狀態反饋的控制演算法的程序設計。
  3. Using commercial finite element software ansys, the numerical simulations of the forming processes of decorated rib and handle, which are key positions in the door outer are conducted and investigated the differences of vpf and tradition forming. by using numerical simulation that investigates the effects of viscous injection flow rate on plank ’ s vpf formability and based on those investigated four - aluminum alloy ’ s vpf. the die has been designed for the door outer ’ s viscous pressure forming

    首先採用商用有限元分析軟體ansys對車門成形中的關鍵部位裝飾筋和把手的成形進行了數值模擬，對比分析了粘性介質壓力成形與剛性模成形的特點;分析了粘性介質壓力成形過程中，粘性介質的注入速率對成形試件壁厚分佈的影響，在此基礎上對四種常用的6000系列鋁合金板材的粘性介質壓力成形進行了有限元數值模擬。
分享友人
分享到 Line

分享到臉書