斜接式 的英文怎麼說
中文拼音 [xiéjiēshì]
斜接式
英文
diagonal built-
From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints
採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。Stability of rock slopes is generally controlled by the structure of rock masses, especially the soft structure surfaces. analysis of rock mass structures is a key to establish geological models and numerical simulation and a foundation to assess the stability of rock slopes. the weak structure surfaces are mainly bedding planes, faults, joints, schistosity plane and contact zones of intrusive bodies. since they are different in genesis and scale, the rock masses are different in features and mechanical intensities. based on the combination of rock structure bodies, 15 basic modes of deformation and failure of rock slope are systematically summarized. the deformation and failure of rock masses actually result from the recombination and rearrangement of these rock bodies. there are 11 types of rock mass structures and various deformation and failure of bank slopes are present in the reservoir area of the three gorge project
巖體結構，特別是軟弱結構面對基巖斜坡變形與破壞具有顯著的控製作用，巖體結構模式分析是建立斜坡地質模型和數學模型的關鍵和評價斜坡穩定性的基礎。巖層層面斷裂構造節理裂隙片理與劈理以及侵入體和圍巖的接觸帶等是控制基巖斜坡穩定的軟弱結構面，這些成因不同大小不一的結構面將巖體分割成性質各異力學強度不均的各種巖體結構體，構成了15種基巖斜坡變形破壞的巖體結構基本模式。不同結構體的重新組合與排列是斜坡失穩的內在原因。As one kind of key equipment in piping work of large - scale turbo - generator set in power plant, the machine is especially applicable to various welding bevels, flat end and angle of outer & inner diameter of ascending pipe, elbow pipe, bend, flange and etc., which greatly meets demands in pipe processing of construction site and manufacturers
本機床是電站大型汽輪發電機組的管道施工的關鍵設備，對直管、彎管、彎頭、法蘭等管體的各種型式焊接坡口，端平面，內外徑過緩斜度及直口，能滿足施工現場和製造廠家對各種管件的加工要求。The gabled brick, tile, and freestone houses had almost dried off for the season their integument of lichen, the streams in the meadows were low, and in the sloping high street, from the west gateway to the medieval cross, and from the medieval cross to the bridge, that leisurely dusting and sweeping was in progress which usually ushers in an old - fashioned market - day
那些帶有用磚砌的山墻和蓋有屋瓦的石頭房子，外面的一層苔蘚已經因為乾燥的季節差不多曬干脫落了草場上溝渠里的水變淺了，在那條斜坡大街上，從西大門到中古十字路，從中古十字路到大橋，有人正在不慌不忙地清掃大街，通常這都是為了迎接舊式的集市日子。Secondly, detailedly analyzing reasons inducing these problems, author finds it is that not thinking of the slope of pipeline and the friction in the process of producing water hammer pressure functions, but, thinking of the effect of the slope of pipeline in the process of producing the consequent water hammer calculative continuity function, which results in the inconsequent illogicality in the whole process of producing
接著，對這些問題存在的原因進行了詳細分析，發現在當前推導水擊壓強公式的過程中沒有考慮管道的傾斜度和摩擦阻力的影響，而在後面水擊計算的連續性方程的推導過程中則考慮了管道的傾斜度，這就導致了在當前連續性方程的整個推導過程中前後矛盾的不合理現象。Niger with phytase activity about 2250 u / ml which selected by protoplast - uv mutation was used as original, prepared it into fungu - suspend - liquid, through uv mutation, daub on the filter - substract. pre - primary - selection was according to the lucency - circle, primary - selection was one fungus inoculate one flask to ferment, secondary - selection was using several high phytase activity fungus through one fungus inoculate 2 - 3 flasks to ferment. then one or two high phytase activity fungus of the secondary selection were used in the next mutation cycle
首先用粗略制備的原生質體經紫外誘變篩選到一株酶活為2250u ml的實驗出發菌；制備成菌懸液，紫外燈下照射誘變，紅光下塗抹篩選平板，恆溫培養2 3d ；按透明圈大小進行預初篩，挑選徑圈比大的菌落接斜面，恆溫培養3d ；按一株一瓶的方式進行初篩；從中選取酶活較大的3 5株，按一株2 3瓶的方式進行復篩；挑取酶活大且穩定的1 2株進入下一代誘變篩選。According to the moving characteristics of tracklayer, when the vehicle is on ramp and the ground ' s vertical pressure is linear, the calculating formulas of relationship between the deviation of the instantaneous steering center, the position of vehicle ' s gravity, steering radius, moving velocity, moving acceleration, and vehicle ' s orientation, were obtained by the theory and method of vector analysis in mathematics and mechanics
摘要根據履帶式車輛的運動特點，運用數力學中矢量分析理論和方法，推導了接地比壓為線性分佈時履帶式車輛在斜坡上轉向時，瞬時轉向中心偏移量與車輛重心位置、轉向半徑、行進速度、加速度、車輛方位相互關系的計算公式。Ultrasonic angle beam examination by the contact method
接觸式超聲斜射探傷方法During the course of the manufacture for packaging 2000 pixel hgcdte irfpa wafer, some crucial techniques are solved, such as the design of the button stem structures with inclined dragging wires applied in cryogenic platform, the optimization of long linear irfpa detector ' s signal wires layouts, the implement of a fanout board having thin film gold metalization for defining the required electrical conductors and a method of hermetically sealed vacuum enclosure of large dimension windows, etc
在用於封裝2000元碲鎘汞焦平面晶元的分置式微型杜瓦研製中，詳細闡明了一種焦平面晶元其裝載面為斜拉式支撐結構的設計，實現了探測器外引功能線的布線優化及其輸出引線工藝改進，並提出了一種大尺寸高氣密光學窗口的焊接方法等關鍵技術。With the development of the network and the multi - processor system, the research, simulation and the impemeni of the system - level fault diagnosis which is the very important means to increase the reliability of the system, are becoming more and more important. on the system - leve1 fault diagnosis, based on the group theory of system - level fault diagnosis that has been put forward by pro f zhang, the paper constructs newly the theory bases, improves on the matrix method, reinforces and consummates group arithmetic of all kinds of test mode, for the first time, analyses and discusses the equation solution of all kinds of models, so al1 the consistent fault patterns ( cfp ) could be found, straightly and high efficiently, even if the sufficient and necessary condition of t - diagnosable is dissatisfied and the complexity of system - level fault diagnosis is greatly decreased, especialy in strong t - diagnosabl6 system. last the simulation system ' s function has been extended and the application hotspot and the development trend have been disscussed
本人在張大方教授等人提出的基於集團的系統級故障診斷的理論基礎上，重新構建了系統級故障診斷的理論基礎，定義了系統級故障診斷測試模型的三值表示；改進了系統級故障診斷的矩陣方法，重新定義了測試矩陣、鄰接矩陣、結點對、結點對的相連運算、極大準集團和斜加矩陣，由此能直觀、簡便地生成集團和極大獨立點集；補充和完善了各類測試模型的系統級故障診斷的集團演算法，通過定義集團測試邊和絕對故障集，簡化了集團診斷圖，由此能較易地找到所有的相容故障模式，即使不滿足t -可診斷性，大大減少了系統級故障診斷的復雜度，尤其是對強t -可診斷系統；首次分析探討了各類測試模型的方程解決，由此從另一角度能系統地、高效率地求出所有的相容故障模式（ cfp ） ：擴充了系統級故障診斷模擬系統的功能，快速、直觀和隨機地模擬實驗運行環境，進行清晰和正確的診斷，同時提供大量的實驗數據用於理論研究，優化演算法和設計。Independent feeding tray : learning from the foreign advanced technology, we discarded the central feeding or side feeding method, and applied the independent tray making materials fed more evenly with automatic control
獨立式斜盤布料裝置：借鑒國外先進技術，一改過去傳統的中間布料或側向布料方式，加料的均勻性和可操作性得到了明顯的改善，並可與電控系統實現連接，實現自動化控制。But that citation will likely be rendered inline when printed, perhaps in italics or underlining, or will appear as a hotlink to the bibliography if rendered in html
，但該引用往往在列印時以內聯形式表示，可能以斜體或下劃線格式表示，也可能作為到書目的熱鏈接出現（如果以html產生） 。Based on the analysis and processing of the digital speckle pattern, the translation and rotation invariant features are discovered, and a one - step feed - forward neural network is creatively proposed which makes it possible to realize the intelligent recognition of interface defects
通過對數學散斑條紋的分析與處理，找出了能代表條紋信息的移位不變與旋轉不變特徵值? ?最大斜率，進而構造一種新的網路模型，即單步前饋式三層網路系統.率先實現了把神經網路系統用在數字散斑無損檢測之中，完成了神經網路系統對粘接界面缺陷的智能辨識Our object is an intermediate frequency modem of a software defined radio transmitter - receiver of multi - service, multi - modulationmode and multi - processdatarate. first, related software defined radio theory is introduced ; later, channels of transmitter - receiver are designed with consideration of data format, modulation, fec, interwaving. and scrambling ; emphasis is placed on theory and implementation of an audio compression algorithm cvsd ( continuous variable slope delta modulation ) and a fec technique convolutional coding - decoding
本文首先介紹了相關的軟體無線電理論；然後完成了包括數據格式，調制方式，糾錯碼方式，交織器和擾碼器等部分的中頻數據機通道設計；接著著重介紹了系統中使用的音頻壓縮演算法cvsd （連續可變斜率增量調制）的原理和實現，以及作為前向糾錯碼的卷積碼編碼理論和編解碼的高效實現。Effects, such as shadow, glow, soft edges, and bevel, can also be accessed from the format tab
效果選項包括:陰影、發光、羽化、傾斜，也可以直接使用格式選項卡。Through systemic analyzing on spiral helical gear transmission with different basic parameters, the essay found out rules of how can such basic parameters influence spiral helical gear engagement characteristics. so it brings forward the auxiliary assembling mode of adopting one straight gear and one helical gear on condition of little axial angle as well as treasures to ameliorate ill engagement performance on condition of large axial angle, another two jobs of the essay are to clarify the wrong concept that spiral helical gear can only transmit movement but not impetus and to provide a brief and practical method of analyzing contact for gear pairs whose surface equations can be written out directly
通過對不同基本參數的螺旋齒輪傳動進行系統研究，找出了螺旋齒輪基本參數對其嚙合特性的影響規律，提出小軸交角條件下可採用一直齒輪、一斜齒輪的齒輪副組合方式，給出了大軸交角條件下嚙合性能不良的改進措施。澄清了螺旋齒輪只能傳遞運動不能傳遞動力的誤區，為能夠直接寫出齒面方程的齒輪副進行齒面接觸分析提供了一種簡便、實用的新方法。The synchronous rectifying and low power sampling technology is used to reduce the power consumption, flexible external loop compensation, error amplifier output clamp are adopted for better system large signal response. the piecewise slope compensation technology is employed to minimize the consequence of over compensation. the sensor resistor is externally connected, which realize output voltage programmable. the overheat protection and under voltage protection modules are integrated in the die to allow the reliable operation of the system
同時，電路設計採用同步整流技術、低功耗電流采樣技術降低功耗，提高轉換效率;採用靈活的外部環路補償技術、誤差放大器輸出嵌位技術以實現良好大信號特性;採用分段斜坡補償技術，消除不穩定因素，並最大程度地減小過補償帶來的問題;採用外接輸出采樣電阻的方式，實現輸出電壓的可編程。Company profile : our main products are kneader, oil pressure machine, welding machine, slicing machine, slanting cutter, water - cooled - type sheet extruder, rubber sheet extruder, and open rubber mixing mill etc
本公司主要生產的機械有密煉機、油壓機、熔接機、開片機、斜割機、冷水式出片機、橡膠出片機、開煉機等。The approximate formula is : the initial bounding rectangle is inflated by pen width, and this result is multiplied by the miter limit, plus some additional margin to allow for end caps
近似公式為：初始邊框按鋼筆寬度擴充，結果乘以斜接限制，再加上用以容納端帽的一些附加邊距。According to the above formula, the initial rigidity and ultimate moment is calculated by developed program to several kinds of gabled frames end - plate connection joint with different types ( such as end - plate connection horizontally placed, vertically placed and inclinedly placed ), different end - plate thickness, different bolt diameter. the different result is compared with different end - plate thickness, the different force arm in joints, different bolt diameters and strength grades
按推導的公式編程計算了不同形式（端板外伸式、端板平齊式、端板斜接、柱腹板加勁） 、不同端板厚度、不同螺栓直徑的門式剛架樑柱端板節點的初始剛度、節點極限彎矩，並比較了不同端板厚度、不同節點力臂、不同螺栓直徑和強度等級、不同連接形式下初始剛度和極限彎矩的變化。分享友人