斜接端 的英文怎麼說

中文拼音 [xiéjiēduān]
斜接端 英文
miter end
  • 斜 : 形容詞（跟平面或直線既不平行也不垂直的） oblique; slanting; skew; bevel; diagonal; askew; inclined; tilted
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  1. From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints

    採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。
  2. As one kind of key equipment in piping work of large - scale turbo - generator set in power plant, the machine is especially applicable to various welding bevels, flat end and angle of outer & inner diameter of ascending pipe, elbow pipe, bend, flange and etc., which greatly meets demands in pipe processing of construction site and manufacturers

    本機床是電站大型汽輪發電機組的管道施工的關鍵設備，對直管、彎管、彎頭、法蘭等管體的各種型式焊接坡口，端平面，內外徑過緩斜度及直口，能滿足施工現場和製造廠家對各種管件的加工要求。
  3. User - friendly computer terminals with touch - screen functions have been installed in the centre. these enable members of the public to gain easy and direct access to information on maintenance responsibility for man - made slopes

    該中心設有方便易用的輕觸式屏幕電腦終端機，讓公眾人士可輕易及直接查閱有關人造斜坡維修責任的資料。
  4. The approximate formula is : the initial bounding rectangle is inflated by pen width, and this result is multiplied by the miter limit, plus some additional margin to allow for end caps

    近似公式為：初始邊框按鋼筆寬度擴充，結果乘以斜接限制，再加上用以容納端帽的一些附加邊距。
  5. The size of the returned bounding rectangle is influenced by the type of end caps, pen width, and pen miter limit, and therefore produces a " loose fit " to the bounded path

    所返回邊框的大小受端帽類型、鋼筆寬度和鋼筆斜接限制的影響，因此產生一個「鬆散適合」于被限定路徑的矩形。
  6. Hold the test specimen by the edges at an angle above the pre - cleaned microscope slide. the specimens should not touch the slide

    手持測試樣本的邊端以一定的角度傾斜在光片的上方。樣本不應接觸光片。
  7. According to the above formula, the initial rigidity and ultimate moment is calculated by developed program to several kinds of gabled frames end - plate connection joint with different types ( such as end - plate connection horizontally placed, vertically placed and inclinedly placed ), different end - plate thickness, different bolt diameter. the different result is compared with different end - plate thickness, the different force arm in joints, different bolt diameters and strength grades

    按推導的公式編程計算了不同形式（端板外伸式、端板平齊式、端板斜接、柱腹板加勁） 、不同端板厚度、不同螺栓直徑的門式剛架樑柱端板節點的初始剛度、節點極限彎矩，並比較了不同端板厚度、不同節點力臂、不同螺栓直徑和強度等級、不同連接形式下初始剛度和極限彎矩的變化。
  8. The theoretical model describing the output properties of double - cladding mof laser has been builded according to the mof ’ s extraordinary mode distribution

    光纖後端面直接輸出時獲得了最大11 . 6w的輸出功率，斜率效率達到了86 %以上。
分享友人
分享到 Line

分享到臉書