斜楔模 的英文怎麼說
中文拼音 [xiéxiēmó]
斜楔模
英文
cam die-
We mainly produce shifting fork and release fork of large - scale and heavy - duty truck ; shifting fork, release fork, shifting block, choosing - gear shaft, reverse - gear shifting fork shaft, right - and - lfet steering joint arm, upper cross arm shaft, wheel hub, link rod of all kinds of cars right - and - left supports, nipbutton of train auto - girder parts ; centeral wedge, fixed lean - board of absorber ; shifting fork, erankshaft, link rod, under - link board, startup pole of motocycle ; mould forging of mine, construction machinery, textile machinery, non - ferrous metal industry, etc
主要生產產品：大、重型卡車變速箱的撥叉、分離叉等；各種轎車變速箱的撥叉、分離叉、撥塊、選檔軸、倒檔撥叉軸、左右轉向節臂、上橫臂軸、輪轂、聯桿，火車自動梁部件的左右支柱、夾扣，減震器的中心楔塊、固定斜板等鍛件；摩托車的撥叉、曲軸、連桿、下聯板、啟動蹬桿總成；礦山機械、建築機械、紡織機械、有色金屬等精模鍛件。Secondly, the finite - element analysis on the typical slope section is performed with establishment of geology model, definition of boundary condition and proper selection of mechanical parameters. the result shows that the slope is of integral stability, and the failure mode mainly comprises infrequent block drop and wedge body breakage. considering the two failure modes of plane failure and wedge body breakage, and stability calculation under different work conditions, the slope stability is discussed and the sensibility ana lysis on its fraction angel and cohesion force is made
然後通過建立地質模型、確定邊界條件、選擇合理的力學參數，取典型斷面對邊坡進行數值分析，分析結果表明斜坡整體是穩定的，破壞類型以零星掉塊和楔體失穩下滑為主；為了定量計算邊坡的穩定性，對邊坡兩種破壞類型：單滑面下滑和雙滑面楔形體下滑，考慮不同工況進行穩定性計算，並對摩擦角和粘聚力進行穩定的敏感性分析。Comparisons by means of numerical simulation are made between this inlet and the normal two - dimensional ramp inlet
數值模擬結果表明，設計工況下該進氣道能夠獲得跟常規二維斜楔式進氣道大致相當的氣動性能。For shutters, the results show : 1 ) according to the formula p =, the theoretical value of is calculated by the effective velocity of the flow, and its engineering value is calculated by the arriving velocity of the flow, the relationship between the theoretical value of and its engineering value is 2 ) the smaller value of declining angle will result in the smaller pressure loss and smaller outlet velocities. as a result, the declining angle of 30 擄 or less is recommended in some places which need small wind velocity, such as broadcasting studio and library, and the declining angle of 45 擄 or less is recommended in places which need big wind velocity, such as cinema and office ; 3 ) the larger value of ratio between the wide of the shutter b and the space between two boards h ( b / h ) will result in the larger pressure loss and smaller outlet velocities. the range of b / h from 0. 8 to 2. 0 and the optimum value 1. 2 is recommended ; 4 ) the range of b from 10 mm to 50 nun and the optimum value 40 mm is recommended ; 5 ) the proper thickness of the boards 8 of the shutters is 1. 5 mm ; 6 ) cuneiform boards should replace the rectangle inlet boards of the shutters in order to obtain better ventilation
數值模擬採用fluent軟體，計算結果用excel進行處理，通過對大量數值工況進行數值模擬計算，結果表明：對于單側百葉風口，計算表明： 1 ）對于公式p = （ ~ 2 ） 2 ，的理論計算值中定義為流體流經百葉風口內部時的速度，即有效速度，而工程上常使用流體的來流速度來計算，計算表明，的理論計算值與工程應用值的關系為（ _ （理論） ） （ _ （工程） ） = 0 . 813 ； 2 ）當來流速度一定時，擋板傾斜角度越小，壓力損失越小、出口速度越小；因此在要求進口風速比較小的場所，如播音室、圖書館等，宜採用擋板角度30的百葉風口；在要求進口風速比較大的場所，如電影院、辦公室等，百葉擋板的角度應選45 ； 3 ）當來流速度一定時，百葉擋板的擋板寬度b與擋板間距h的比值b h越大，壓力損失越大，出口速度越小，計算表明，鑒于壓力損失、出口風速、板間形成渦流區的大小，百葉擋板的b h值取0 . 8到2 . 0之間， b h = 1 . 2為最佳值； 4 ）當來流速度一定時，在計算的條件下，當百葉擋板寬度b = 40mm時，百葉擋板的阻力系數最小，考慮到渦流區等的影響，建議選用10mm b 50mm的百葉擋板；西安建築科技大學碩士學位論文5 ）百葉擋板的厚度取為1 . sinln為好; 6 ）百葉擋板的入口側可選用具有傾斜度的楔形擋板來代替矩形擋板，利用其較好的導流作用，可得到更好的出流效果。分享友人