斜滑塊 的英文怎麼說
中文拼音 [xiégǔkuāi]
斜滑塊
英文
angled-lift splits-
The design and machining technology process of its molding part including the front moulding plate 、 front mould kernel 、 back mould plate 、 back mould kernel 、 back mould set piece 、 incline guide pin 、 slide steatite etc, and the choice and calculation of technology parameters of the impotent part, the design process of extrusion outfit, inject system and other makeup are specified in detail ; test and product have been introduced
詳細地敘述了模具成型零件包括前模板、前模仁、后模板、后模仁、后模鑲件、斜導柱、滑塊等的設計與加工工藝過程，重要零件的工藝參數的選擇與計算，推出機構與澆注系統以及其它結構的設計過程，並對試模與產品缺陷作了介紹。Through the theory of light radiation and intensity, we can use the fewest leds to satisfy the luminous intensity demand. through image segmentation theory, we can accurately pick module up from the test stripe when it is put in wrong directions. through image processing theory, we can acquire correct information and avoid the bad effects from the asymmetric chemistry reaction and instability of the devices
用光的輻射和強度理論，我們計算出了獲得足夠圖像強度所需的最少光源;用圖像分割理論，我們在試紙條傾斜放置或有垂直方向上的偏移時，準確地提取出了各模塊的數據;用平滑濾波和均值濾波理論，我們濾除了由於反應不均勻及硬體設備不穩定帶來的噪聲;用交遇區設計線性分類器的方法，我們降低了有限樣本設計線性分類器帶來的誤差，提高了檢驗準確度。Abstract : having been finished the design of squeeze casting machine shell model, it provides design key points of squeeze casting model with slant slide parts, researches the technology about the product and optimizes the parameters of technoloy and model structure. the results are suitable for similar squeeze casting of parts
文摘:通過對機座擠壓鑄造模具的設計，給出了斜滑塊擠鑄模的設計要點，研究了製件的工藝過程，對工藝參數和模具結構參數進行了優化，研究結果可供類似零件的擠壓鑄造所借鑒Secondly, the finite - element analysis on the typical slope section is performed with establishment of geology model, definition of boundary condition and proper selection of mechanical parameters. the result shows that the slope is of integral stability, and the failure mode mainly comprises infrequent block drop and wedge body breakage. considering the two failure modes of plane failure and wedge body breakage, and stability calculation under different work conditions, the slope stability is discussed and the sensibility ana lysis on its fraction angel and cohesion force is made
然後通過建立地質模型、確定邊界條件、選擇合理的力學參數，取典型斷面對邊坡進行數值分析，分析結果表明斜坡整體是穩定的，破壞類型以零星掉塊和楔體失穩下滑為主；為了定量計算邊坡的穩定性，對邊坡兩種破壞類型：單滑面下滑和雙滑面楔形體下滑，考慮不同工況進行穩定性計算，並對摩擦角和粘聚力進行穩定的敏感性分析。A mould with an oblique guide pin scroll box structure was designed for the core pulling in two directions of a mould with two cavities
採用能解決一模兩腔的兩面抽芯問題的斜導柱滑塊結構的模具結構，設計出電流線圈架注射模模具。A flap vlave used in pumping station is a kind of hydraulic - operated automatic gate, which is similar to a hinged check vaive. because of their simple structure and reliability, being able to shorten the length of outlet passage and facilitate the starting of pumping system in comparison with siphonic vacuum - distroied cutoff scheme. so it is propitious to be used and save investment but at the same time, flap valves always show some disadvantage
因拍門簡單、可靠，與虹吸真空破壞截流閉鎖方式相比，可以縮短出水管道（流道）長度，並利於泵系統起動，與快速閘門相比，拍門也有諸多優點，閘門門體易關閉不到位或卡住不能活動，因為門槽和?塊較軸孔容易殘留異物，閘門門體克服滑動阻力不僅無機械增益，且阻力和動力不在一直線上，門體易傾斜而自鎖，而拍門的工作可靠性則遠高於快速閘門。Rising middle mountains abounds with steep slops and cliffs and monoclinical middle mountains high slants. this make them easy to collapse in high slants and slope failure usually happens in acclinal slopes. regional geology structure exerts an obvious constraints on the water system of the dazhaigou - haizigou valley
斷塊隆升中山坡面多陡坡和峭壁，單斜中山的逆傾坡以峻坡為主，易產生林金沙江白鶴灘水電站庫區大寨溝、海子溝流域泥石流形成環境與流量研究料崩塌，而單斜中山的順傾坡上易形成滑坡。分享友人