斜裂紋 的英文怎麼說
中文拼音 [xiélièwén]
斜裂紋
英文
oblique crack-
The results indicate that a stable deformation localization band occurs in the coal cutting course and develops to macroscopic crack ; the deformation localization band is slantwise ; while the cutter tooth is used, the deformation localization develops slowly, and the localization becomes wider and the strain value in the band area higher afterwards ; when the point - attack pick used the localization develops quickly and the localization band becomes narrow and the strain value in the band lower
研究表明：截齒截割煤體過程中，煤體出現穩定的變形局部化帶，且最終發展為宏觀裂紋；煤體變形局部化帶為一個傾斜帶：刀齒截割時，變形局部化發展較慢，但產生變形局部化后，局部化帶寬且帶內應變值較高；而鎬齒截割時，變形局部化發展較快，但產生局部化后，局部化帶窄且帶內應變值不如刀齒高。A two - dimensional plain strain finite element model of infinite plate is developed to investigate the ultrasonic wave propagation and scattering on three kinds of cracks : parallel to the surface, 450 oblique angle to the surface, and quarter - circle
摘要建立了無限長板的具有吸收邊界的二維平面應變有限元模型，在研究了脈沖超聲波在無限長板中傳播的基礎上，對板中平行於表面的裂紋、與表面成45的斜裂紋和四分之一圓周弧形裂紋三種情況的脈沖超聲波散射進行了重點研究。Bi - material interfacial fracture theories are researched with a phenomenon that cracks extend along interface. a gradient invading model of interface crack at the crack tip can gain stress fields along interface. so a formula of energy release rate for 3d braided cmc is deduced and the corrected formula of the energy release rate is examined with test results
研究了裂紋沿界面擴展的雙材料界面斷裂理論，利用傾斜侵入界面的裂紋模型解析了裂紋尖端沿著界面的應力場，推導了表徵三維編織cmc復合材料斷裂韌性的能量釋放率公式g _ c ，並且用試驗結果驗證了能量釋放率公式的正確性。Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure
試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。While these angles might not seem much, such tumbling would have dramatically increased stresses inside these moons, leading very likely to " a global pattern of tectonic fractures, " nimmo explained
這些角度看起來不大，但這種傾斜可能會急劇地增加這些月亮內部的壓力，常常可能導致「一個全球的構造裂紋」 ，尼姆解釋說。With the aid of the " pseudo - traction " method, the superposition technique and the arrived fundamental solution, a method for getting the stress intensity factor ( sif ) for material such as rock with center inclined crack under compressive loading are given
採用「偽力法」和疊加原理，結合所求的基本解，給出了含中心斜裂紋的巖石類材料在壓縮荷載作用下的應力強度因子（ sif ）的解法。分享友人