斜軸端面 的英文怎麼說

中文拼音 [xiézhóuduānmiàn]
斜軸端面 英文
clinopedion
  • 斜 : 形容詞（跟平面或直線既不平行也不垂直的） oblique; slanting; skew; bevel; diagonal; askew; inclined; tilted
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 端面 : end face; end plane; end surface; head face; side surface; terminal face
  1. Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure

    試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。
  2. A detailed model of non - linear parametric excitation vibration coupling the stay cable and the girder, in which the static sag as well as the geometric non - linearity are considered, is proposed in this paper. based on several numeric examples investigated by the galerkin method composed with the integration strategy, several kinds of factors effecting stay cable parameter vibration are studied. another parameter vibration model by the axial excitation is presented and the corresponding nonlinear equations are derived

    本文創新地提出了斜拉橋拉索-橋面耦合參數振動模型，推導了索-橋耦合非線性參數振動方程組，聯合galerkin法及數值積分方法，對各種特性的拉索進行了數值求解，得出了影響拉索參數振動的各種因素；提出了斜拉索受軸向端激勵參數振動模型，導出了模型的非線性振動方程，使用諧波平衡法得出了產生參數振動需要的最小激勵幅值、共振時瞬態及穩態的振動幅值及索拉力的變化特性，並用數值積分方法對實際斜拉橋拉索進行了計算，分析了拉索阻尼對參數振動的影響。
  3. The outcome suggest that, firstly, the change of light transmission with the continuous change of parameters is periodic ; secondly, as far as the degree of effect is concerned, the light transmission of air - spaced prisms is much more sensitive to the change of the parameters than that of the glue spaced ones ; thirdly, as to the prisms glued with the same dielectric, the effect of prisms whose optical axis parallels to the glued layer is intense than those whose optical axis parallels to the plane determines by the normal of incident face and that of the cut face

    研究認為，激光偏光棱鏡的光強透射比隨各參量的連續變化都呈現出一定的周期性；各參量對空氣隙型偏光棱鏡的影響要比對膠合型棱鏡的影響大的多；同種介質膠合的棱鏡，各參量對光軸平行於切割斜面的設計類型比光軸平行於切割面的法線和入射端面的法線所組成的平面的設計類型的影響要大。
分享友人
分享到 Line

分享到臉書