斜鋼筋 的英文怎麼說

中文拼音 [xiégāngjīn]
斜鋼筋 英文
diagonal bar
  • 斜 : 形容詞（跟平面或直線既不平行也不垂直的） oblique; slanting; skew; bevel; diagonal; askew; inclined; tilted
  • 鋼 : 鋼名詞（鐵和碳的合金） steel
  • 筋 : 名詞1 （肌的舊稱） muscle2 [口語] （肌腱或骨頭的韌帶） tendon; sinew 3 [口語] （可以看見的皮下靜...
  • 鋼筋 : concrete iron; concrete reinforcing bars; rebar; reinforcing bar; reinforced bar; reinforcing ste...
  1. Then, a thunderous sound came from the rear of the house. the kitchen on the back slope had collapsed under the sudden onslaught of a torrential flow of muddy water, and had fallen on the last row of concrete houses on the slope. rocks of all sizes, washed down by the muddy water, smashed through the windows into the rooms and then rushed through the doors into the living room and out into the courtyard at lower levels

    謝師兄在打坐中依稀聽到爸爸走進客廳的聲音，突然一聲山崩地裂的巨響從屋后傳來，後山腰的廚房被突如其來的土石流沖擊倒塌，壓到斜坡上最後一排的鋼筋房子，土石流沖破兩三間房間的窗戶玻璃，大小石塊挾雜在洪水中，從窗口沖進房間，又從房門竄流出來，直奔地勢較低的客廳和庭院，家頓時變成土石流的出水口。
  2. Based on tests of nine 1 / 2 - scaled model slabs under vertical loads, the paper analyzed load - deformation curve and proposed limit value of height - width ratio under axial loads. 2. based on aseismic tests, the paper put forward a model of concrete frame, silica brick and a combination of the two, proposed that the silica brick works as a 45 compression bar, analyzed the factors which may influence bearing capacity of the slab and advised a formula including the numbers of bays and of storeys of the frame

    通過對墻板模型的抗震性能試驗研究，建立了由鋼筋混凝土框格、砌塊以及兩者協同作用三個部分組成的承載力極限狀態下的理論簡化計算模型；提出了墻板中填充塊等效斜壓桿寬度按45度計算的統一量化標準；分析了影響墻板承載力的主要影響因素，給出了表達墻板框格層數和跨數不同的斜截面承載力實用設計計算公式。
  3. The construction techniques of sinking well and explode in water are introduced. auto climbing form panel technique is applied in the construction of main tower

    斜拉橋主橋墩設計為鋼筋混凝土圓端型沉井結構，其中詳細介紹了沉井下沉施工技術，同時介紹了水下松動控制爆破技術。
  4. There is not composite enhancing effect to shear resistance of reinforced concrete beams between steel fiber and stirrups

    鋼纖維與箍筋之間在提高鋼筋混凝土梁斜截面承載力方面不存在「藕合增強效應」 。
  5. The wall was equaled to an elastic composite slab with silica bricks as main body and concrete rib beams, columns and outer frame as reinforcing fiber. ( 2 ) elastic - plastic stage. the wall was equaled to a rigid frame - oblique compression bar model in which concrete frame was equivalent to a rigid frame while silica brick was equivalent to a oblique compression bar

    （ 1 ）彈性階段? ?將墻體視為一種以輕質砌塊為基體，混凝土肋梁、肋柱、外框為增強纖維的復合材料等效彈性板； （ 2 ）彈塑性階段? ?將墻體視為一個由鋼筋混凝土剛架和與之鉸接的砌塊等效斜壓桿組成的剛架斜壓桿組合模型； （ 3 ）破壞階段? ?將墻體視為肋梁嚴重破損的梁鉸框架模型。
  6. Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating

    箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。
  7. There are rope bridges, arch bridges, tower bridges, cable bridges and reinforced concrete bridges

    有早期的索橋、拱橋、塔橋、斜拉橋和鋼筋混凝土橋。
  8. Calculation method and test investigation of oblique section consolidation of reinforced concrete bridge

    橋梁加固鋼筋混凝土受彎構件斜截面承載力計算方法及試驗研究
  9. Test research and theoretic study on shear strengthening of reinforced concrete restrained beams using externally applied carbon fabrics reinforced plastics under concentrated loads is presented in this thesis, which is part of the project of construction bureau of hunan province

    本文結合省建設廳課題碳纖維加固鋼筋混凝土結構的受力變形性能及加固方法研究，對鋼筋混凝土約束梁斜向貼cfrp抗剪加固進行了試驗研究和理論探討。
  10. Considered local damage due to steels corrosion, fatigue, prestressing loses, whole bridge incline and distortion, this paper studies damage diagnosis technique of the cable - stayed bridge and determines the location and size of damages for yonghe cable - stayed bridge, which has been used after 15 years

    針對鋼筋腐蝕、疲勞、預應力鬆弛、橋梁整體傾斜或變形所引起的斜拉橋局部破損，本文以使用15年後的永和斜拉橋為研究對象，對大型斜拉橋破損診斷技術進行研究，對永和斜拉橋破損位置進行定位、對其破損程度進行評價。
  11. The experiments showed that the cracking process of such restrained beams in this paper can be divided into three phases, that is, formation of the fanning zones, initialization and development of splitting cracks along longitudinal reinforcement, and accelerating development of the critical crack and / or cracks ( diagonal, flexural ). during the last two phases, it was observed that further opening of some cracks led to some

    研究結果表明，鋼筋混凝土有腹筋約束梁的裂縫開展過程大致可分為扇形區逐步形成、劈裂裂縫出現和發展、最終臨界裂縫（斜裂縫或彎曲裂縫）加速發展至破壞等階段。在後兩個階段中存在某些裂縫發展減弱同時某些裂縫迅速開展的「此消彼漲」的現象。
  12. According to test results of two specimens of local transfer rc joint from inclined column to beeline - shaped wall under vertical static loads and results of corresponding finite element analysis ( ansys ), fundamental behaviors of the joint are achieved, which include paths of vertical load transfer before and after cracking, stress distributions, occurrence and development of cracks and final failure mode of the joint

    本文通過兩個鋼筋混凝土斜柱?一字形薄壁柱局部轉換節點在豎向荷載作用下的靜力試驗以及有限元分析，獲得了該節點的基本性能，其中包括開裂前後的豎向荷載的傳遞路徑、試件應力分佈，裂縫的發生、發展，及試件最後的破壞形態等。
  13. Then the coupling beams with new reinforcement layout were made an inquiry into, and the improvement on the seismic behavior by coupling beams diagonally reinforced with a few rows in end regions was found out at last, based on the observations of the experimental phenomena and the analysis of the measurement result, and by the comparison of seismic behavior by making use of hysteretic response, ductility and energy dissipation behavior, a conclusion is presented : the code for design and construction of reinforced concrete high - rise structures ( the draft asked for advise hi 2000 ) ca n ' t ensure that the coupling beams have fairly good seismic ductility ; the result of improvement of the seismic ductility of the coupling beams by the increase hi stirrups besides the strengthen of longitudinal detailing reinforcement was n ' t obvious ; the coupling beams diagonally reinforced with a few rows in end regions have fairly good mechanisms, and the ductility and the behavior of energy dissipation are better than conventionally reinforced concrete coupling beams, so it is suitable to te tised in short coupling beams

    本文通過對三根小跨高比（均為l h = 1 . 0 ）剪力墻洞口連系梁在低周反復荷載作用下的試驗，了解了嚴格按《鋼筋混凝土高層建築結構設計與施工規程》 （ 2000年徵求意見稿）設計的連梁具有的抗震性能，研究了採取增大連梁配箍量同時加強縱向構造筋的方案對抗震性能的影響，並進一步對新的配筋形式的連梁進行了探討，了解了在連梁梁端配置多排交叉斜筋方案對連梁抗震性能的改善。通過對試驗現象的觀察和量測結果的分析，利用荷載?位移滯回曲線、延性和耗能性能等指標對各個試件的抗震性能進行了比較，最後得出結論： 《鋼筋混凝土高層建築結構設計與施工規程》 （ 2000年徵求意見稿）不能保證小跨高比連梁具有較好的抗震延性：通過增大連梁配箍量同時加強縱向構造筋的方案對改善連梁的抗震延性的效果不太明顯；梁端配置多排交叉斜筋的連梁具有相對較好的受力性能，其延性和耗能性能等各項性能指標均優于普通配筋連梁，宜在深連梁中採用。
  14. Steel fiber reduces the size effect of shear resistance of reinforced concrete beams without web reinfocements. the size effect formula is proposed in this paper, it is better agreement with test data. 5

    鋼纖維對鋼筋混凝土無腹筋梁斜截面承載力「尺寸效應」具有降低作用，本文提出了與現行規范相銜接的鋼筋鋼纖維混凝土腹筋梁斜截面承載力「尺寸效應」計算公式，與現有的試驗資料符合良好。
  15. The research works and conclusions of this paper as following : 1. besed on the test results published over the word of reinforced concrete beams without web reinforcements and with stirrups, the systematically statistical analysis is carried out to set up the fomula of shear resistance of reinforced concrete beams using the uniaxial tensile strength of concrete. it provided the basis of strtistical analysis for shear resistance of steel fiber reinforced concrete beams

    根據收集到的國內外對鋼筋混凝土無腹筋梁和鋼筋混凝土有腹筋梁的斜截面承載力試驗研究成果，進行了比較系統的綜合統計分析，提出了採用混凝土軸心抗拉強度研究成果，進行了比較系統的綜合統計分析，提出了採用混凝土軸心抗拉強度指標的鋼筋混凝土梁斜截面承載力計算公式，為鋼筋鋼纖維混凝土梁受剪承載力試驗結果的統計分析提供了基礎。
  16. Based on the analysis of the experiment results, it is regarded that the seismic behavior of the truss src columns is higher than those of rc columns. the steel requirements, the crosswise rod dimension and the welding quantity are the main factor, which influence on the truss type src columns

    通過對試驗結果的分析，認為配置角鋼桁架式空腹鋼骨的鋼骨混凝土柱的抗震能力明顯高於鋼筋混凝土柱，配鋼率和斜腹桿的大小與焊接質量是影響桁架式空腹鋼骨的鋼骨混凝土柱的主要因素。
  17. In order to reveal load mechanism and failure mode of thick pile caps, by means of the test of 1 / 4 - scale models of thick pile caps with six piles and post - handling study of 3 - dimensional non - linear finite element adina, this paper points out the shortage, which is that the design of pile caps is carried out by flexural strength in chinese technical code for building pile foundations jgj94 - 94 and american reinforcement concrete building construction code aci318 - 02, promulgates that the failure mode of thick pile caps is punching failure and load transfer mechanism is the strut - and - tie, which is that zones of concrete with primarily unidirectional compressive stresses are modeled by compress struts, while tension ties are used to model longitudinal reinforcement over pile

    摘要為揭示厚承臺的傳力機理和破壞形式，通過對4個1 : 5比例的六樁厚承臺的模型試驗研究與三維非線性有限元adina的后處理研究，指出中國建築樁基技術規范jgj94 - 94與美國鋼筋砼房屋建築規范aci318 - 02規范中，承臺以彎曲強度進行配筋計算的設計方法之不足，揭示出厚承臺的破壞模式是沖切破壞，傳力機理是以帶有主要單向壓應力的砼區域作斜壓桿，樁頂區域的縱筋作拉桿的空間桁架。
  18. Analysis of rc beam failure in diagonal tension with meshless method

    利用無網格方法分析斜拉破壞鋼筋混凝土梁
  19. The coal unloading chute is a kind of the underground reinforced concrete box structure. the main beam of coal unloading chute being made skew, this kind of structure has been the first time in domestic

    進煤系統的主體建築物卸煤溝為地下式鋼筋混凝箱形結構，卸煤溝溝頂主梁採用斜向布置，這種結構布置形式在國內尚屬首次。
  20. In accordance with the deformation analysis of lean - caused disaster engineering and the deformation control in rectification, analysis method of the leaning reinforced concrete frame is presented using the theory of structural engineering, numerical analysis and disaster characteristics. on the basis of the analysis method, finite element is applied to analyze the stress and deformation conditions of structure in order to obtain the rectifying displacement. appling of fuzzy math to value the ultimate bearing capacity of structural element, the author puts forward the fuzzy general evaluation method of the element, and using the theory of structural engineering also gets the rectifying load

    針對傾斜病害工程的變形分析和糾傾扶正過程結構的變形控制問題，本研究論文根據建築結構理論，採用數值分析方法，並結合病害表現特徵，提出對鋼筋混凝土框架結構傾斜病害的變形分析方法；在結構的變形分析的基礎上，運用有限元方法對結構進行數值模擬，對結構的應力狀態及變形狀況作進一步的分析，確定糾傾位移量；運用模糊數學理論，提出對鋼筋混凝土病害框架結構構件的承載能力的模糊綜合評判方法，並結合建築結構理論得出最終糾傾加載量。
分享友人
分享到 Line

分享到臉書