斜齒條 的英文怎麼說
中文拼音 [xiéchǐtiáo]
斜齒條
英文
screw rack-
Based on the ostwald - de waele equation, the leakage characteristics of power - law transmitted by helical gear pump are researched, and the leakage model of power - law in the clearence is founded, and - the velocity distributing and the leakage capacity are worked out by the boundary condition. the power loss of leakage is got through the clearence leakage capacity, and the friction power loss is attained by the velocity distributing. the mathematic calculation model
利用冪律流體本構方程，首次對聚合物流體在斜齒齒輪泵中的漏流特性進行了研究，建立冪律流體在間隙中的泄漏模型，利用邊界條件求出速度分佈及泄漏量；由間隙泄漏量得到漏流損失功率，由速度分佈得到流體摩擦功率損失，並得到間隙最優解的數值計算數學模型，同時給出實例及數值計算結果。The four main types of gears (spur, helical, worm, and bevel)and a rack and pinion are shown in figure 7.
圖7所示是四種主要的齒輪（巨齒輪，斜齒輪，蝸輪和傘齒輪）以及齒條和小齒輪。2. the flux characteristics of ordinary helical gear pump are lucubrated by theory for the first time, on this condition the selective qualification of the helical gear pump is gained
首次對普通斜齒齒輪泵流量特性進行了深入的理論研究，在此基礎上研究了全齒廓嚙合斜齒齒輪泵流量特性，首次得到了完全消除斜齒齒輪泵流量脈動的螺旋角的選擇條件。Through systemic analyzing on spiral helical gear transmission with different basic parameters, the essay found out rules of how can such basic parameters influence spiral helical gear engagement characteristics. so it brings forward the auxiliary assembling mode of adopting one straight gear and one helical gear on condition of little axial angle as well as treasures to ameliorate ill engagement performance on condition of large axial angle, another two jobs of the essay are to clarify the wrong concept that spiral helical gear can only transmit movement but not impetus and to provide a brief and practical method of analyzing contact for gear pairs whose surface equations can be written out directly
通過對不同基本參數的螺旋齒輪傳動進行系統研究，找出了螺旋齒輪基本參數對其嚙合特性的影響規律，提出小軸交角條件下可採用一直齒輪、一斜齒輪的齒輪副組合方式，給出了大軸交角條件下嚙合性能不良的改進措施。澄清了螺旋齒輪只能傳遞運動不能傳遞動力的誤區，為能夠直接寫出齒面方程的齒輪副進行齒面接觸分析提供了一種簡便、實用的新方法。Gear drawing standards - part 1, for spur, helical, double helical, and rack
齒輪繪圖標準.第1部分:正齒輪斜齒輪人字齒輪和齒條The software uses two entity configuration methods : extruding and simulating entity cutting in realizing three dimensional configuration, which successfully achieve three dimensional configuration of involute columnar vertical gear, involute columnar helical gear, standard vertical spline, archimedes worm and disco - cam
軟體在三維造型功能實現上使用了拉伸和模擬實體切削兩種實體造型方法，成功地實現了漸開線圓柱直齒輪、漸開線圓柱斜齒輪、標準直齒條、阿基米德蝸桿和盤形凸輪的三維造型。Sawblade for ripping and cross cutting of softwoods and hardwoods up to 50 mm and singlo or multiple chipboard panels up to 60 mm with good finish. use on table saw
鋸片帶交叉斜齒，適用於開條和橫鋸50毫米以下各種乾燥軟、硬木和厚度不超過60毫米的刨花板，切割質量精佳，配置於推臺鋸。Stable, reliable klin driving helical gearing such driving system guarantees the highest flexibility and reliablility at low cost of maintenance. the whole system can operate under a " relaxed " mode
穩定、可靠的窯爐傳動有斜齒輪傳動，這種傳動系統均保證最高的靈活性及可靠性且維修費用低，整套傳動系統可在「放鬆」的條件下工作。分享友人