旋轉切刀 的英文怎麼說

中文拼音 [xuánzhuǎnqiēdāo]
旋轉切刀 英文
cutting rotor
  • 旋 : 旋Ⅰ動詞1 （旋轉） whirl 2 （用車床切削或用刀子轉著圈地削） turn sth on a lathe; lathe; pare Ⅱ名詞...
  • 轉 : 轉構詞成分。
  • 切 : 切Ⅰ動詞1 （合; 符合） correspond to; be close to 2 （用在反切后頭 表示前兩個字是注音用的反切）見 ...
  • 刀 : Ⅰ名詞1 （切、割、削、砍、鍘的工具） knife; sword 2 （形狀像刀的東西） sth shaped like a knife 3 ...
  • 旋轉 : revolve; gyrate; rotate; spin ; revolution; revolvement; rotation; circumgyration; circulation
  1. Analyse the tooth geometry of klingelnberg cyclo - palloid spiral bevel gear., according to the relative position and kinematic relation of the cutter heads, virtual crown gear and the processed wheel blank, established the system of coordinates of the gear cutting, dedcuced the tooth face equation of the virtual crown gear, according to relations of the gear cutting and space theory of engagement, deduced the tooth face equation of klingelnberg cyclo - palloid spiral bevel gear, and drawing the three - dimensional graphs of the virutal crown gear and klingelnberg cyclo - palloid spiral bevel gear according to the design and setting parameters

    對克林貝格擺線齒錐齒輪進行齒面幾何分析。根據銑齒加工中刀盤、搖臺和輪坯的相對位置和相對運動關系建立了切齒嚙合坐標系，由矢量的旋轉推導了產形輪齒面方程;根據空間嚙合原理和切齒嚙合關系推導了被加工齒輪的齒面方程;由設計參數和銑齒調整參數計算得到齒面離散數據，繪制了產形輪和擺線齒錐齒輪的三維齒形。
  2. Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece

    將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義
  3. The dynamo runs at rull speed to drive main shaft, then the main shaft makes the emulsifying wings in emulsification grove rotate, which absorbs the liquid in its brand groove into ring groove through guide vanes on upper and lower sides of the groove. the vanes spins circularly at high speed with the main shatf as center, and the blade and emulsificaton groove cut and crush it continuously. after that. it gers squeezed by the vanes highspeed centrifugal rotation. at last, it finishes isotropt emulsification tratment within extremely short time after continuous circulating mixing

    由電動機全速運轉帶動主軸，經主軸轉動乳化框槽內之乳化翼片，使其將桶槽內之液體經框槽上、下兩側之導流葉片吸入環狀框槽內，經以主軸為中心高速圓周旋轉葉片；連續使乳化翼端刀面與乳化框間極小之間系高頻率之強力切割剪斷、粉碎，再借葉片高速離心旋轉排擠，持續循環混合，以極短之時間即可完成均質乳化之處理。
  4. Abstract : the mathematical model of reverse - rotary til ler was derived on the basis of relationship between design parameters ( includin g geometric parameters and motive parameters ) and power consumption

    文摘:該文對潛土逆轉旋耕機刀片的切削過程進行了受力分析，建立了同時含有兩種設計參數（刀片的幾何參數和旋耕機的基本速度參數）的功耗模型。
  5. Two or more cutters, rotating freely on ball-bearings, are set in the head of the bit.

    可在鉆頭上安裝兩個或更多的支在滾珠軸承上自由旋轉的切削刀具。
  6. This machine is of vertical crushing structure, and the material is fed into the crushing chambezr through a hopper, crushed by simultaneous cutting of both fixed and movable knives and rotating impact of rotating knife, and entered into the catcher automatically under the effect of rotating centrifugal force, and the dust is filtered and recovered by dust collector through a bag

    本機為立式粉碎結構，物料由進料斗進入粉碎室，利用旋轉刀的旋轉沖擊，固定刀和活動刀同進剪切而獲得粉碎，粉碎好的物料經旋轉離心力的作用，自動進入捕集袋，粉塵由吸塵箱經布袋過濾回收。
  7. In order to improve the performance of a up - cut rotary blade, the sidelong portion angle of the blade was analyzed based on soil - blade geometry

    摘要為提高反轉旋耕刀的性能，根據旋耕刀運動的特點，從旋耕刀幾何學及切削角度方面出發，對反轉旋耕刀正切面角度及對磨刃面的影響進行了分析。
  8. This machine of horizotal crushing structure, and the material is fed into the crushing chamber through a hopper, crushed by cutting and impact of both fixed and rotating knives, and flows to the exit automatically under the effect of rotating centrifugal force

    料斗進入粉碎室，利用旋轉刀與固定刀沖擊、剪切而獲得粉碎，經旋轉離心力的作用，物料自動流向粉碎機出口處。
  9. The head of the main shaft is featured with 15 degrees pitch angle and the work table can rotate 360 degrees for grinding milling, lateral milling, spiral milling, oblique milling, suitable for carpenter ' s spiral boring bit, end milling tool, copper round saw, and cutting and milling for various hardware

    旋轉，做磨銑、側銑、螺旋銑、斜度銑，適合木工用之螺旋?頭及金屬切削刀具之?頭、端銑刀、銅圓鋸及各類五金零件之銑削加工之用。
  10. Metal - cutting tools ; milling cutters, rotation, flute direction, end thrust

    金屬切削刀具.順排屑槽方向旋轉軸向推力的銑刀
  11. The so - called " turning ", refer to operating workers ( namely lathe work ), utilize rotatory sport of work piece and cutter team cut sport is it change size and form of blank to come first according to the request of drawing pattern at lathe, make it become a kind of metal cutting method of the acceptable product

    所謂「車削」 ，是指操作工人（即車工）在車床上根據圖紙圖樣的要求利用工件的旋轉運動和刀具的先隊切削運動來改變毛坯的尺寸和形狀，使之成為合格產品的一種金屬切削方法！
  12. Steel rotary slitting knives and steel spacing collars

    鋼制旋轉式切口刀和鋼制間隔墊圈
分享友人
分享到 Line

分享到臉書