旋轉模塑 的英文怎麼說

中文拼音 [xuánzhuǎnmósù]
旋轉模塑 英文
mwr
  • 旋 : 旋Ⅰ動詞1 （旋轉） whirl 2 （用車床切削或用刀子轉著圈地削） turn sth on a lathe; lathe; pare Ⅱ名詞...
  • 轉 : 轉構詞成分。
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 塑 : 動詞（塑造） model; mould
  • 旋轉 : revolve; gyrate; rotate; spin ; revolution; revolvement; rotation; circumgyration; circulation
  1. Study on the mechanism of void formation in roto - moulding of long - fiber reinforced resin

    長纖維增強液態反應性樹脂復合材料旋轉模塑成型工藝氣泡形成機理試驗分析
  2. Efficient to lose fat, adopt micro - computer technology to make the vibration strongly effect on the abdomen, which part with most fat of the body. inner - desighed strong motor effect on the organism directly. unique auto change direction mode, makes the full dimension vibration of the organism

    迴旋塑身腰帶運用微電腦技術，將強效振動裝置直接作用於脂肪最為集中的腹背部，內置的強有力的電動機直接作用於肌體，產品獨有的大幅度的水平移動自動變換方向運動模式，使肌體大范圍全方位共振，同時加快身體血液循環，微電腦控製程序可自動逐步增強產品運動力度，使用過程中自動轉換運動方向。
  3. The innovation of multiple mechanism boundary surface plasticity model is that the effect of rotation of principal stress axial directions and large shear displacement of sand in the earthquake induced liquefaction are taken into account at the same time in the model

    獨到之處在於所建立的多機構邊界麵塑性模型能夠同時考慮土體在復雜荷載作用下主應力軸旋轉的影響和砂土地震液化時剪切大位移特性。
  4. Thermoplastic tanks made from blow or rotational moulded polyethylene - tanks for the above ground storage of chemicals - requirements and test methods

    吹模或旋轉模製聚乙烯熱塑性罐.地上化學制劑儲罐.要求和試驗方法
  5. Thermoplastics tanks made from blow or rotational moulded polyethylene - tanks for the above ground storage of chemicals - requirements and test methods

    吹模或旋轉模製聚乙烯熱塑性罐.化學製品地上存儲罐.要求和試驗方法
  6. Thermoplastic tanks made from blow or rotational moulded polyethylene - tanks for the above ground storage of chemicals - requirements and test methods ; german version en 13575 : 2004

    吹模或旋轉模製聚乙烯熱塑罐.地上化學制劑儲罐.要求
  7. Thermoplastics static tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - blow moulded polyethylene, rotationally moulded polyethylene and polyamide 6 by anionic polymerization tanks - requirements and test methods

    家用燃料油煤油和柴油的地上存儲用熱塑性固定儲油罐.通過陰離子聚合吹塑聚乙烯儲油罐旋轉模製聚乙烯和聚酰胺6儲油罐.要求和試驗方法
  8. This paper uses the method of tensor to proof the tenable condition of generalized plastic potential, discuss the mathematical essential of the associated and disassociated flow rule and the relation of the yield surface and plastic potential surface, reason the expression of plastic factor strictly. debate the limitation on drucker ' s postulate. subsequently, this paper gives the mathematical basis of constitutive theory involving the rotation of principal stress axes. so it is proved that the mathematical and mechanical foundation of the generalized plastic mechanic

    本文運用張量的方法論證了廣義塑性位勢理論成立的充要條件，討論了關聯與非關聯流到法則的數學實質，屈服面與塑性勢面的關系，嚴密推導了塑性因子的表達式，討論了drucker公設的局限性，並給出了考慮主應力軸旋轉時土體本構模型理論的數學依據，系統的論證了廣義塑性力學成立的數學力學基礎。
  9. Numerical modeling for porphroblast s rotation and deformation of augen fabrics in ductile shear zones is done by a large plastic deformation programm based on detailed investigation to three ductile shear zones, taihangshan mountains

    在對太行山阜平地區三條剪切帶作了詳細觀察和測量的基礎上，就斑晶旋轉和眼球構造進行了塑性大變形的計算機模擬。
  10. The model can reflect the multi - sets feature of the rock masses in practice, consider the influence of the joint orientation and strength to the rock masses deformation feature, and simulate the simultaneous sliding, tension and close behaviors of the multi - sets jointed rock masses extending the joint surface, and reflect the plastic deformation induced the rotation of the principle stress axes. the result can be extended to fractured rock masses with arbitrary set joints

    該模型能反映實際工程中巖體的成組節理特性，考慮節理產狀和強度對巖體變形特性的影響，可用來模擬巖體中多組節理同時存在滑動、張開、閉合的行為，並能反應由於應力主軸旋轉所產生的塑性變形的影響。
分享友人
分享到 Line

分享到臉書