曲半徑 的英文怎麼說
中文拼音 [qūbànjìng]
曲半徑
英文
bilge radius-
Minimum bend semidiameter during installation 15d
固定安裝時的最小彎曲半徑： 15d7. minimum bend semidiameter during installation 15d
固定安裝時的最小彎曲半徑： 15d3. the permitted bending semidiameter is not less than four times of cable outside diameter
3 .電纜允許彎曲半徑不小於電纜外徑的4倍2. when installing, the permitted bending semidiameter is not less than four times of cable outside diameter
2 .敷設時電纜的允許彎曲半徑應不低於電纜半徑的4倍Stretch - bending former is used to manufacture curved pieces with large size and high shaped precision. generally, these pieces are relatively large winding radius extrusion or sheet bending profiled bars. especially, stretch - bending former is the needed equipment to produce rims, ribs, edges and strips of airplanes
拉彎機是生產加工飛機上的框肋緣條等型材零件的必須設備，常用於製造尺寸大、外形準確度要求較高、相對彎曲半徑大的擠壓和板彎型材彎曲件。Permissible bending radius : not less than 6 times of overall diameter for unarmored cable ; not less than 12 times of overall diameter for armored or screened cable ; not less than 6 times of overall diameter for screened flexible cable
推薦允許彎曲半徑：無鎧裝層電纜應不小於電纜外徑的6倍；有鎧裝層或屏蔽層結構的電纜應不小於電纜外徑的12倍；有屏蔽結構的軟電纜應不小於電纜外徑的6倍。Permissible min. bending radius : no less than 6 times of the completed cablediameter in case of unarmoured cable ; no less than 12 times of the completed cable diameter in case of armoured or copper tape screened cabel ; no less than 6 times of the completed cable diameter in case of screened flexible cabel
3電纜的允許彎曲半徑：無鎧裝層的電纜，應不小於電纜外徑的6倍；有鎧裝層或銅帶屏蔽結構的電纜，應不小於電纜外徑的12倍；有屏蔽層結構的軟電纜，應不小於電纜外徑的6倍。Testing of fibre optic elements ; determination of the minimum bendig radius of fibre optic cables
光纖元件檢驗.光纜最小彎曲半徑的測定4. high bending stability the minimum bendable radius is only over two times as long as o. d. of thermocouple
4可撓性好最小彎曲半徑只有熱電偶外徑的2倍以上Through comprehensive analysis of the tbph, the relationship between the induction heater site and rotary axis and the relationship between the support wheel and initial site of the front clapper have been concluded. the minimum nominal curvature radius has also been determined
通過對加熱彎管成形的綜合分析，得出感應加熱器與回轉中心的位置關系及支撐輪與前夾頭初始位置關系，並確定了加熱彎管最小名義彎曲半徑。While installation the ambient temperature should not be lower than 0, and the bending radius radius should not be less than 10 times of outer diameter of cable
敷設電纜時的環境溫度不低於0 ，最小彎曲半徑應不小於電纜外徑的10倍。Bending radii for seamless and welded steel tubes ; design sheet
無縫和焊接鋼管的彎曲半徑.設計圖表When installing crooked radius aluminium bring or aluminum pipe should smaller than cable 30 times of external diameter, unless it install when not transporting it should handle with care, can t twist, can t not when not piling up heavy pressure, should keep dry, ventilate, not moist while preserving
安裝時彎曲半徑鋁帶或鋁管的應不小於電纜外徑的30倍，安裝運輸時應輕拿輕放，不能扭曲，堆放時不能重壓，存放時應保持乾燥、通風、不潮濕。Aerospace ; bending radii for tubes ; approximate values for cold working
航空航天.管彎曲半徑.冷加工用近似值Test method for static minimum bending radius for coaxial trunk, feeder, and distribution cables
共軸總線饋電線和配線電纜用靜態最小彎曲半徑的試驗方法Steel tubes. bending radii. recommended minimum values for unalloyed steel tubes
鋼管.彎曲半徑.非合金鋼管最小推薦值In the second part, we introduce and discuss a new domain constant, the pseudo - hyperbolic radius of starlikeness. we also give some properties of some existing domain constants under the change of quasiconformal mappings
在第二部分中，我們主要引進一個新的區域常數?星形偽雙曲半徑，給出了它的一些性質，並對已有的一些區域常數在擬共形映射下的變化進行討論。Measurement of inside crook radius of elbow of 90 176 ; series pipe
系列圓管彎頭內彎曲半徑的測量Via theory testify, bend loss has been neglected when curved radius is larger than 2mm
理論證明在彎曲半徑大於2mm的情況下，彎曲波導所引起的輻射損耗很小。Feature : anti - bending of hose body, small bending radius, good stiffness, with or without metal fittings available
特性：管體耐曲撓、彎曲半徑小、挺性好。帶或不帶金屬接頭。分享友人