曲折縫 的英文怎麼說

中文拼音 [qūzhéféng]
曲折縫 英文
gg-20u457
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 折 : 折動詞[口語]1. （翻轉） roll over; turn over 2. （倒過來倒過去） pour back and forth between two containers
  • 縫 : 縫名詞1. （接合處） seam 2. （縫隙） crack; crevice; fissure; slit
  • 曲折 : 1 （彎曲） circuitos; intricate; ups and downs; tortuous; winding; zigzag 2 （復雜的、不順當的情...
  1. He kept the front wheels astride the crack as he followed its zigzag course.

    他在使前輪分跨裂縫的同時曲曲折折前進。
  2. He keeps the front wheels astride the crack as he followed its zig-zig course.

    他在使前輪分跨裂縫的同時曲曲折折前進。
  3. However, single types are difficult in sewing heavy material and more materials once, it ll cause poor stability feeding and much attrition. in order to ensure zig - zag stitch, linking stitch, locking stitch. wemust adopt double type. needle plate and presser foot of double type should be changed together if you want to use double tye istead of single type. the size of their scres and installs are all - purpose

    有時為了保證曲折線縫拼縫鎖邊等縫紉要求，就要採用雙長型送布牙，如果要想把單長型改換成雙長型時，必須同時更換雙長型的針板和壓腳，其螺釘和安裝尺寸是通用的
  4. The reduction factors derived from curve fitting based on calculation results by the finite element program ( ansys ) considering all kinds of damages such as cutouts, corrosion, cracks, denting, initial deflection and residual stress are introduced to modify the effective width of perfect panel in the present paper

    本文考慮板中可能存在孔洞、腐蝕、裂縫、局部撞損和初始焊接變形或殘余應力等損傷和初始缺陷，對不同的損傷形式用有限元程序（ ansys ）進行大量的計算，通過曲線擬合的方法引入折減系數對完好板格的有效寬度進行修正。
  5. As soon as the normal section cracks, the crack firstly appears in the flexural region. at this moment, the load - deflection curve has a turning point. with the increase of the load, the rigidity of the beam decreases compared with that before cracking because of the development of cracks in flexural region, and the formation and development of diagonal cracks toward the loading point, the load - deflection curve is basically linear till the beam fails

    正截面開裂前，荷載撓度曲線基本為線性，截面剛度較大；正截面開裂時，裂縫先在純彎段出現，荷載撓度曲線出現轉折點，隨著荷載的增加，純彎段正裂縫的發展以及剪跨段斜裂縫的產生並向梁的受壓區加荷點發展，使梁的剛度較截面開裂前減少，荷載撓度曲線也基本為線性直到梁破壞。
  6. Loading different shapes of slots in the patches of antennas will cut off the original surface current and the current has to flow around the slots that make its route longer. this course is equally satisfactory in result of inserting cascade inductances in the equivalent circuit of antenna

    當在貼片表面開不同形式的槽或細縫時，切斷了原來的表面電流路徑，使電流繞槽邊曲折流過而路徑變長，在天線等效電路中相當于引入了級聯電感。
分享友人
分享到 Line

分享到臉書