曲柄 的英文怎麼說

中文拼音 [bǐng]
曲柄 英文
[軌] crank曲柄扳手 brace wrench; cranked wrench; 曲柄刨床 crank planing machine; 曲柄臂 [機械工程] crank web; crankshaft web [cheek]; crank body [arm]; 曲柄車床 crank shank lathe; 曲柄鉆 brace drill
  • : 曲名詞1 (一種韻文形式) qu a type of verse for singing which emerged in the southern song and ji...
  • : Ⅰ名詞1 (器物的把兒) handle 2 (植物的花、葉或果實跟莖或枝連接部分) stem 3 (言行上被人抓住的材...
  1. Chain adjusters and crank cotter pins for bicycles

    自行車鏈調整器和曲柄扁銷
  2. Crankshaft harmonic balancer

    曲柄軸諧和平衡器
  3. In the simulation, the mpc technique of msc. nastran is used to simulate the mechanical behavior of contact between the interfaces of piston pin and bearing of small end, crankpin and big end bearing, connecting rod body and bearing cap ; also constraints are applied to the connecting rod reasonably

    分析中採用了patran中的多點約束( mpc )技術,有效地模擬了活塞銷與小頭孔內表面、曲柄銷與大頭孔內表面以及連桿體與大頭蓋接觸面的力學接觸狀態,並對連桿進行合理的約束。
  4. They were twirling a brace drill.

    他們當時正在轉動曲柄鉆。
  5. Fixed or rotating handles for hand wheels, control levers, etc

    固定或旋轉式手輪曲柄把手和操作桿等把手
  6. Cycles. cotter pin and assembly of the axle cotter pin crank

    自行車.扁銷和輪軸扁銷曲柄總成
  7. Crank case explosion

    曲柄箱爆燃
  8. As the crankshaft rotates, the crankpin swings in a circle around the shaft.

    隨著軸的轉動,曲柄銷繞主軸作圓周擺動。
  9. The cap and rod have bearings which permit the crankpin to rotate freely within the rod.

    軸瓦蓋和連桿中有軸瓦,它允許連桿內的曲柄鎖自由地轉動。
  10. Smooth and finish the crankpin to roundness

    曲柄銷磨光並精加工到正圓。
  11. Crankpin bearing lubrication

    曲柄銷承潤滑
  12. The load map and wearing maps of the crankshaft journals and crankpin are obtained under various operating conditions

    研究表明:氣缸壓力和轉速升高后,曲柄銷和主軸頸的磨損均呈現增加趨勢。
  13. The crank is an offset section of the crankshaft.

    曲柄軸的偏置部分。
  14. The circular movement of this crank operates the valves register.

    曲柄的圓周運動帶動了閥門的記錄器。
  15. The crank reference pulse originates from a variable reluctant pickup which senses a projection on the engine's flywheel.

    曲柄參考點脈沖信號由一個變磁阻傳感器產生,它從發動機飛輪上的突起感受信號。
  16. The propeller will windmill and crank the engine

    螺旋漿將旋轉並轉動引擎的曲柄
  17. Will you please help me to crank up the engine

    請你幫助我用曲柄發動引擎好嗎?
  18. This drilling adopts crank connecting link and walking beam percussion mechanism, which make the drilling possess two percussive functions, normal drilling takes connecting link impact as main mode, when encountering special situation and the connecting link impact can not drill, it can transform into hoisting impact, the stroke length can be modulated, it realizes automatic percussive drilling due to continuous operating of connecting link percussive mechanism, these can enhance drilling efficiency and relieve labor intensity ; it adopts pumping reverse circulation to drain slag, which not only resolves the drilling difficulty in special stratum such as pebble and gravel stratum and hard stratum, but also resolves the problem that the percussive drill ' s efficiency is low ; it adopts spur gear differential mechanism as double cylinders lazy tongs of main hoist, which not only ensures the balance state of drilling tool, but also reduces the mechanical design, and reduces the cost ; the bottom plate traveling motion of this drilling machine adopts walking type ; the drilling tower adopts hydraulic pressure uprising, and reduces the assistant operating time

    該鉆機採用曲柄連桿、游梁式沖擊機構,使鉆機具有兩種沖擊功能;正常鉆進以連桿沖擊為主,遇到特殊情況,用連桿沖擊不能鉆進時,可轉為卷揚沖擊,沖程可調,因連桿沖擊機構連續工作,所以實現了自動沖擊鉆進,可提高鉆進效率,減輕勞動強度;採用泵吸反循環的方式排渣,既能有效解決卵礫石地層、堅硬地層等特殊地層鉆進的困難,又很好地解決了沖擊鉆機效率低下的問題;採用直齒圓柱齒輪差速機構作為主卷揚的雙筒同步機構,既保證了鉆具處于平衡狀態,又大大簡化了該機構設計,降低了成本;該鉆機底盤行走移位採用步履式;鉆塔採用液壓起立,減少了輔助作業時間。
  19. The crank used to give motion to a grindstone or similar device

    曲柄用於給石磨或其他裝置施力的把手
  20. In addition, java3d can only accomplish the regular geometry sculpting and ca n ' t accomplish the irregular geometry sculpting. to solve this flaw, a new way of sculpting the gyre - solid and changing - section - brace by approaching the solid with small slice is put forward. at the same time, rendering and third dimension disposing are settled in this paper

    另外,在系統開發過程中,針對java3d三維造型功能類中僅包含標準幾何形體的問題,這里用四邊形面片逼近面的方法解決了回轉體和變截面曲柄的三維建模,以及這種建模方式下的渲染和真實感處理問題。
分享友人