曲率矢量 的英文怎麼說
中文拼音 [qūlǜshǐliáng]
曲率矢量
英文
buckling vector-
Through the loss model of lim, best efficiency control scheme is proposed based on the vector control, by which low efficiency of lim under light load or low speed is improved. the control scheme is proved effective through simulation under a specified speed - location curve
通過建立電機損耗模型，在矢量控制的基礎上設計了最優效率控制策略，解決了輕載或低速運行時的效率低下問題，通過指定速度位置曲線下的模擬分析驗證了控制策略的有效性。In the paper, based on the method of low pair replacing with high pair, the problem of cam design was transferred to that of linkage design. by means of rotary unit vectors, the equations of displacement, velocity and acceleration of the replacement mechanisms were developed. and then, the virtual linkage ' s length and direction were deduced
論文基於高副低代原理，將平面凸輪機構設計與再現函數的平面連桿機構設計統一為同一種方法，運用圓向量函數建立代換機構的位移、速度、加速度矢量方程式，求取虛擬連桿桿長和方向，由此展開凸輪理論廓線、實際廓線、曲率半徑和壓力角的求解，並得出用圓形刀具加工凸輪時刀具中心的軌跡方程。Secondly, to achieve the independent regulation of active and reactive power output from the generator side which is designed for the purpose of tracing the maximum wind - energy capturing. the paper has analyzed the mathematic model of the ac excited doubly - fed machine and the stator field orientation control strategy of the motor as vscf wind power generator. thirdly, it has put forward and designed the dual pwm converter with the capacity of energy flowing bidirectional aimed at the demand of rotor energy bidirectional flow. the author constructed reliable and integrated experimental system and did a series of experimental study including no - load, cutting - in network and power generation at, below and above the synchronous speed
論文首先分析了風機運行特性及其最佳風能利用原理，通過模擬及實驗驗證了採用直流電機的輸出特性模擬風力機的最大輸出功率曲線的可行性，並給出了模擬系統的硬體結構；然後為了實現交流勵磁發電機有功、無功功率獨立調節機理，分析了交流勵磁雙饋發電機的數學模型和在追蹤最大風能捕獲變速恆頻風力發電時必需的定子磁鏈定向矢量控制策略；針對雙饋發電機轉子能量雙向流動的要求，提出並設計了具有能量雙向流動能力的雙pwm交流勵磁用變頻器；最後為實現從理論到實踐的全面研究，研製出了一套小功率完整的雙pwm變頻器交流勵磁的雙饋風力發電機實驗系統，進行了空載、並網、同步速及上、下的發電運行等一系列的運行實驗；所完成的模擬和實驗研究均驗證了理論、模型和控制策略的正確性、可行性。Taking the meshing theory of conjugate curved surface as a foundation, utilizing array method of rotation transformation of vector, the meshing equation and contour surface equation of conical cam mechanism with swinging conical roller follower were analyzed and derived, and the calculation formula of pressure angle and synthetic curvature of the mechanism was presented, thus laid a solid theoretical foundation for enhancing the machining accuracy of conical cam, improving its processing method and achieved the integration of cam cad / cam
摘要以共軛曲面嚙合理論為基礎，運用矢量的旋轉變換矩陣法，分析並推導了圓錐滾子擺動從動件圓錐凸輪機構的嚙合方程和廓面方程，並給出了機構的壓力角和綜合曲率的計算公式，為圓錐凸輪加工精度的提高，改進其加工方法，實現凸輪cad / cam一體化奠定了堅實的理論基礎。分享友人