曲軸曲柄 的英文怎麼說
中文拼音 [qūzhóuqūbǐng]
曲軸曲柄
英文
throw of crankshaft-
Crankshaft harmonic balancer
曲柄軸諧和平衡器Cycles. cotter pin and assembly of the axle cotter pin crank
自行車.扁銷和輪軸扁銷曲柄總成As the crankshaft rotates, the crankpin swings in a circle around the shaft.
隨著曲軸的轉動,曲柄銷繞主軸作圓周擺動。The cap and rod have bearings which permit the crankpin to rotate freely within the rod.
軸瓦蓋和連桿中有軸瓦,它允許連桿內的曲柄鎖自由地轉動。The load map and wearing maps of the crankshaft journals and crankpin are obtained under various operating conditions
研究表明:氣缸壓力和轉速升高后,曲柄銷和主軸頸的磨損均呈現增加趨勢。The crank is an offset section of the crankshaft.
曲柄是曲軸的偏置部分。It is composed of two components : level move and rotation. level move is realized by the co - operation of oil vat, handspike and synchronizer. rotation is realized by the brace and the triangle oriented axis
平行移動是由液壓油缸推動,通過推動軸承傳到推桿、同步盤,並相互配合實現的;旋轉運動是由曲柄、三角架導向軸完成的。It is applied to sorts of locomotive engine, in course of revolving of crank and connecting rod mechanism, there are revolving of the crankshaft, swinging of the connecting rod and reciprocating motion, so its motion state is complex, and periodic unbalanced force, by a few components, is great
曲柄連桿機構在高速運轉過程中,有曲軸的轉動、連桿的擺動及活塞的往復運動,其運動狀態復雜,各個部件所產生的周期性不平衡慣性力大,是引起發動機振動的主要原因。Crank bearing liner
曲柄軸承瓦The sampling rate of the system can reach 3704 sps, and the crank angle is 1. 94 degree per sampling point corresponding to the crank speed of 1200r / min. in the mean time, the position signal of the piston could be collected by photo - electricity switch
本研究首先設計和實現了摩擦力採集電子電路系統,裝置最大采樣率可達到3704sps ,在曲軸轉速為1200r / min時,對應曲柄轉角1 . 94度采樣點,並且可以採集用來確定活塞位置的光電開關的信號。Take out active plug of the water mouth, leak sewage, next, cover the plug, then turn bent axle handle for 10 seconds, thecentral axis drives mop roller at the speed of 120 circles, i. e. swinging, dehydration and dryness
拉開導水口的活動塞子,排掉污水,再蓋回塞子封閉導水口。曲軸手柄旋轉10秒鐘,中心軸帶動滾筒旋轉達到120轉的速度高速甩水,產生離心力脫水。It whips and mixes the fresh air and crankcase fumes as it rotates.
它旋轉時,把新鮮空氣和曲柄軸箱氣體攪混在一起。( 2 ) the crack compares with one depth with the first steps and the second steps natural frequency vibration, crack position near crank arm and main shaft transition round natural frequency little place under crankshaft ; with the third steps and the fourth steps natural frequency vibration, the smaller close to the second crank arm of crankshaft and round place natural frequency of the main shaft transition the position is
( 2 )裂紋同一深度比以第1階和第2階固有頻率振動,裂紋位置越靠近曲軸中間曲柄臂與主軸過渡圓處固有頻率越小;以第3階和第4階固有頻率振動,位置越靠近曲軸第二個曲柄臂與主軸過渡圓處固有頻率越小。Pour detergent into the water inlet round hole on the cover of dehydrator, then connect the hose, turn bent faxle handle, waterrom 16 inlets spout to the cleaned part of rotating roller, so, under the function of centrifugal force, the high speed turningrotating roller can completely stir water, therefore achieve thecleanness effect
:洗滌劑從脫水器蓋子上加水口圓孔加入,接入水管,搖轉曲軸手柄,水就從上,而下於16個出水孔噴射向高速旋轉的滾筒需清潔部位,高速旋轉的滾筒在離心力作用下攪動產生水旋渦,從而達到洗滌效果。Tile cutting disks, deep drawing tools, plain bearings, sealing and sliding sealing rings, guide gibs, liners and bushings, shaft protective sleeves, rolls for cold rolling mills, tools for diecasting pulverized materials, cutting disks
飾面花磚切削盤、深拉工具、滑動軸承、密封圈和滑動密封圈、導向槽、襯墊和軸套、曲柄軸套、冷壓磨碎機軋輥、硬模鑄造研磨材料的工具、刀盤。Crankshaft bearimg cover
曲柄軸軸承蓋Throw of crank shaft
曲軸曲柄曲柄半徑The radius of a circle described by a crank, cam, or similar machine part
(曲軸的)半徑曲柄、凸輪或類似機器部件形成的圓的半徑Cycles. pedal axle and crank assembly with square end fitting. assembly dimensions
自行車.帶方頭配件的腳蹬軸和曲柄組件.組裝尺寸Information on the enterprise beijing zhongtian ruihua scientific trade co., ltd. and their services, like rehabilitation and collect on one hand and thigh and control technology on the other, is available in the firm profile
公司專業從事積蓄、收集、聚集、身體復原、恢復以及軸頸、腿、柱、 (量角器的)臂、鐵心、彎管、曲柄、邊腳、 (角焊縫的)焊腳和控制技術學業務。分享友人