曲軸銷 的英文怎麼說

中文拼音 [qūzhóuxiāo]
曲軸銷 英文
crank pin
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 銷 : Ⅰ動詞1 （熔化金屬） melt （metal）2 （除去; 解除） cancel; annul 3 （銷售） sell; market:產銷平衡...
  1. One machinery makes wen zhoudong limited company is to be engaged in research, development, production, sale is domestic and international the gas a powerful person of all sorts of medium compressor, a powerful person piece, lever of annulus of bedspring, piston, piston, piston, sealing ring, crosshead, crosshead is sold, copper is covered, bolt of connecting rod, connecting rod,

    溫州東一機械製造有限公司是從事研究、開發、生產、銷售國內外各種介質壓縮機的氣閥、閥片、彈簧、活塞、活塞環、活塞桿、密封圈、十字頭、十字頭銷、銅套、連桿、連桿螺栓、軸瓦、曲軸、缸體及缸蓋、缸套、凈化設備及部件、冷卻器等壓縮機配件的專業技術型企業。
  2. Cycles. cotter pin and assembly of the axle cotter pin crank

    自行車.扁銷和輪軸扁銷曲柄總成
  3. The rod-bearing cap attaches the connecting rod to the crankpin.

    連桿軸瓦蓋將連桿安裝到曲軸銷上。
  4. As the crankshaft rotates, the crankpin swings in a circle around the shaft.

    隨著曲軸的轉動，曲柄銷繞主軸作圓周擺動。
  5. The load map and wearing maps of the crankshaft journals and crankpin are obtained under various operating conditions

    研究表明：氣缸壓力和轉速升高后，曲柄銷和主軸頸的磨損均呈現增加趨勢。
  6. There is no clutch, gearing, oil changes, smog check, pistons, rings, valves, crankshaft, flywheel, rods, wrist pins, etc., etc

    沒有離合器，傳動裝置，機油變化，尾氣檢查，活塞，活塞環，閥門，曲軸，飛輪，連桿，肘節銷，等等。
  7. Adjust the amount of oil supplied to the thread take up and needle bar crank 3 by turning adjust pin 4

    調整挑線桿和針桿曲軸部3的油量時，轉動油量調整銷4進行調整。
  8. The minimum amount of oil is reached when marker dot a is brought close to needle bar crank 3 by turning the adjust pin in direction b

    調詳銷刻點a從圖的位置向b方向轉動，轉動到接近針桿曲軸3時，油量最小。
  9. The reassigned smoothed pseudo wigner - ville distribution ( rspwvd ) is introduced, which has less interference and higher resolution than other time frequency distributions like wigner - ville, choi - williams etc. it is used to detect the multi - knocking of engine such as cylinder, piston pin, valve, crank bearing, connecting rod bearing and jib knocking. a new fault diagnosis technique based on the rspwvd for the engine multi - knocking problem is proposed. by comparing the bispectrum and bicoherence of the gear vibration signals, it is demonstrated that bispectrum has an advantage over bicoherence for feature extraction of such signals

    第四章首次引入一種重分配方法，得到干擾項少而解析度高的重分配平滑偽魏格納維爾分佈（ rspwvd ） ；對發動機曲軸主軸承響、連桿軸承響、活塞銷響、活塞敲缸響、氣門響和挺桿響等常見機械異響故障振動信號特徵進行了全面地比較分析；通過對各種異響故障特徵信號的分析研究，提出基於rspwvd的發動機多異響故障診斷策略，利用該策略可以準確識別不同的發動機異響故障。
  10. After ascertaining the motion projection, the engine model with double connecting rods and crankshafts is established and the rationality about the structure of the model has been tested. at the same time, the standard component parts library such as bolt, nut, bond and pin is builded, which will be convenient to later design

    確定運動機構方案后，在分析裝配模型，裝配關系等基礎上用solidworks建立了零件庫和螺栓、螺母、鍵、銷等標準件庫，根據內燃機結構特點實現新型雙連桿雙曲軸內燃機的裝配模型，並檢查了整個樣機模型設計的合理性。
分享友人
分享到 Line

分享到臉書