最優含水量 的英文怎麼說

中文拼音 [zuìyōuhánshuǐliáng]
最優含水量 英文
optimum moisture content
  • 最 : 副詞（表示某種屬性超過所有同類的人或事物） most; best; worst; first; very; least; above all; -est
  • 含 : 動詞1 （東西放在嘴裏 不咽下也不吐出） keep in the mouth 2 （藏在裏面; 包含） contain 3 （帶有某種...
  • 水 : 名詞1 （由兩個氫原子和一個氧原子結合而成的液體） water 2 （河流） river 3 （指江、河、湖、海、洋...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 最優 : optimal; optimum最優策略 optimal policy; optimal strategy; 最優設計 optimum design; 最優值 optima...
  1. By the large quantity of indoor and field soil mechanics test, this paper investigated physics and mechanics property of xigeda stratum and xigeda compounding filling, profoundly and systematically studied on shearing strength, cbr ( including indoor cbr and field cbr ) and intensity feature of xigeda compounding filling. the new achievement and cognition as follows : ( 1 ) cbr value is decided by moisture content and mudstone content of xigeda compounding filling. the filling material can satisfy minimum intensity standard of express highway when mudstone content is less than some fixed value, ( 2 ) this paper established field cbr standard value which can synthetically evaluate the filling material nature and field compaction degree. ( 3 ) the optimal compacting mean of xigeda compounding filling is hard oscillation first and weak oscillation later, not traditional way which is weak oscillation first and hard oscillation later. ( 4 ) this paper put forward the conception of optimum moisture content in construction different from optimum moisture content of indoor impaction

    本文以昔格達填料強度特徵為研究對象，通過大量的室內及現場試驗，從昔格達地層巖組的物理力學性質、昔格達填料的物理性質入手，對昔格達填料的抗剪強度、室內承載比及現場承載比特徵進行了較系統地研究，獲得了如下認識及進展：昔格達混合填料承載比值受填料含水量及其中泥巖含量的影響，當泥巖含量小於一定值時，昔格達混合填料具有較高的承載比值，能夠滿足高速公路對填料的最低強度要求；建立了綜合評判昔格達填料性能及現場壓實效果的現場承載比（ cbr ）標準；對于昔格達填料而言，最佳的碾壓方式為先強振后弱振而不是傳統的先弱振后強振；提出了與室內擊實最優含水量相區別的施工最佳含水量的概念。
  2. The optimum conditions for air electrode preparation were shown as follow : 20 % ptfe and 20 % mno2 in active layer, thickness of active layer 0. 15 - 0. 25mm and the ratio of active carbon to ethine black 4 : 1 ; 60 % ptfe in the gas diffusion and waterproof layer, employing na2so4 as pore - making agents, thickness 0. 35 - 0. 45mm, colding forming and layer sequence catlytic layer / gas diffusion and waterproof layer / current collector layout ; employing 40 meshed nickel screen as current collector and thermal treatment temperature over 200

    確定了制備空氣電極的優化工藝條件，催化層中ptfe含量約20 ， mno _ 2的最佳含量約為20 ，催化層中活性炭和乙炔黑的比例為4 ： 1 （質量比） ，厚度在0 . 15 - 0 . 25mm之間。防水透氣層中ptfe的含量約為60 ，以無水硫酸鈉作為造孔劑，厚度一般為0 . 35 - 0 . 45mm 。電極各層採用催化層/防水透氣層/集流體的排布方式，冷壓成型，熱處理對空氣電極的性能影響較大，熱處理溫度不低於200 。
  3. During this time both the monthly average algae density and lasting time increased year after year. the main algae forming algae bloom was cyanophyta and the dominant generas were microcystis. the accumulation of nutrients ( such as total nitrogen and total phosphorus ) with high concentration, high temperature of water and strong sunshine caused the algae bloom

    結果表明，水溫較高的夏秋季（一般為7 9月）是天津市城市供水水源的藻類高發期；近幾年，高藻期含藻量呈逐年增加趨勢，持續時間呈逐年延長趨勢；高藻期水源水以藍藻為主，所佔藻類總數最高和最低比例分別為91和70 ，其中的優勢屬為微囊藻屬；水源水中高含量的氮、磷等營養鹽是藻類高發的內在因素，水溫、光照等是外在誘發因素。
  4. This thesis regard internal property reorganization in the group of pangang as the research object, from chengdu seamless steel pipe limited liability company with chengdu iron and steel works inside exterior environment reorganizing in front and back commences, making use of to exceed the makel - bot with of five factors competition models and the method of factors analysis, after analyzing the reorganization of the business enterprise a profession for facing competes the situation. develop the development the business enterprise with the profession industry from the international local profession rival circumstance after analyzing the reorganization should the market position of the establishment with develop the strategy target. make use of the swot the analysis the method, to after the reorganization the development strategy of the business enterprise, from manage the angle proceeded the fixed position analyzes, for after the reorganization business enterprise development provided four kinds of developments strategy that eligibility choose : the brave development strategy, request the resources advantage, funds advantage, human resource advantage, technique advantage that new company make the most of new business enterprise in empress in reorganization, is an essential condition to increases to manage the level, quickly technique reforms, develop the high and additional worth product with new product production line, as soon as quikly change to strong and large business enterprise, realizes soon steel aircraft carrier dream ; dispersion strategy, the technology market quota with deal with produce high additional worth product, completely promote business enterprise brand image, extend high carry product of the exaltation product, is a necessary means to increases business enterprise performance, realizes business enterprise target ; defense strategy, adjusting the business enterprise organizes construction, reducing the intensive type in labor and the low additional worth product line, lower bad the property saves the deal, alleviating the business enterprise burden, attaining the casual wear go to battle, benefitting to the challenge that make frontal attack the rival ; withdraw strategy, compress the production of the high depletion and high cost product, simplify the production craft, controlling the cost of the end product in the lower level, is a valid path to increases business enterprise competition ability

    本論文以攀鋼集團內部的資產重組為研究對象，從成都無縫鋼管有限責任公司與成都鋼鐵廠重組前後的內外部環境入手，運用邁克爾?波特的五力競爭模型及因素分析法，分析了重組后的企業所面臨的行業競爭態勢。從國際國內行業競爭對手情況和本行業發展動態分析了重組后企業應確立的市場地位和發展戰略目標。運用swot分析法，對重組后企業的發展戰略，從管理角度進行了定位分析，為重組后企業發展提供了可選擇的四種發展戰略：即大膽發展戰略，要求新公司充分運用重組后新企業的資源優勢，資金優勢，人力資源優勢，技術優勢，是提高管理水平，加快技術改造，開發高附加值產品和新產品生產線，盡快立於強勢企業之林，早日實現「鋼鐵航母」夢的必要條件；分散性戰略，提高產品的科技含量和生產高附加值的產品，全面提升企業品牌形象，擴大高端產品的市場份額，是提高企業效益，實現企業目標的必要手段；防禦性戰略，調整企業組織結構，削減勞動密集型和低附加值產品生產線，降低不良資產存量，減輕企業包袱，做到輕裝上陣，有利於迎擊競爭對手的挑戰；退出性戰略，壓縮高消耗、高成本產品的生產，降低低端產品的比例，精簡生產工藝，將最終產品的成本控制在較低水平，是提高企業競爭力的有效途徑。
  5. The dynamic plan, which is a basic way of math, has great scope for using in optimization regulation. it decomposes a complicated problem into a series of simple problem which contain one variable and agree with the decision having many stages about reservoir ' s optimization regulation

    動態規劃法是最優化技術中適用范圍最廣的基本數學方法，它是把一個包含多變量的復雜問題分解成一系列各自只包含一個變量的簡單問題，適合於水庫興利調度的多階段決策。
  6. Abstract : during construction of the capital international airport ' s garage building project, the c50 and over c60 high performance concrete has been adopted for its construction. for the aim of 1, to get a maximum reduction of cement comsumption 2, to lower the concrete ' s hydration heat 3, to reduce concrete ' s shrinkage and cracks, and 4, to promote concrete ' s performance, a high quality chilled blast furnace superfine slag has been adopted as an admixture. furthermore, the adoption of some other minerals as the admixtures to get a high performance concrete has been carried out. as a result, these procedures and operations would have developed considerably the potential activity of concrete, and eventually the multiple performance and multiple function of concrete would have been improved and promoted. in conclusion a good result has been achieved in practice

    文摘:首都國際機場停車樓工程中，採用c50及c60以上高性能混凝土，為最大限度減少水泥用量，降低水化熱，減少收縮與裂縫，提高混凝土的性能，優選了有效成分含量高、質量好的水淬高爐礦渣磨細后單獨摻用，或再與其他礦物組分復合作為高性能混凝土的摻合料，以充分發揮礦渣的潛在活性，從而使混凝土的多項性能得到極大的改善和提高，並在實際應用中取得了良好的效果。
  7. During construction of the capital international airport ' s garage building project, the c50 and over c60 high performance concrete has been adopted for its construction. for the aim of 1, to get a maximum reduction of cement comsumption 2, to lower the concrete ' s hydration heat 3, to reduce concrete ' s shrinkage and cracks, and 4, to promote concrete ' s performance, a high quality chilled blast furnace superfine slag has been adopted as an admixture. furthermore, the adoption of some other minerals as the admixtures to get a high performance concrete has been carried out. as a result, these procedures and operations would have developed considerably the potential activity of concrete, and eventually the multiple performance and multiple function of concrete would have been improved and promoted. in conclusion a good result has been achieved in practice

    首都國際機場停車樓工程中，採用c50及c60以上高性能混凝土，為最大限度減少水泥用量，降低水化熱，減少收縮與裂縫，提高混凝土的性能，優選了有效成分含量高、質量好的水淬高爐礦渣磨細后單獨摻用，或再與其他礦物組分復合作為高性能混凝土的摻合料，以充分發揮礦渣的潛在活性，從而使混凝土的多項性能得到極大的改善和提高，並在實際應用中取得了良好的效果。
  8. In this paper, the so preparing self - compacting concrete with low and middle strength using super fine mountain sand artifical sand and phosphorus slag is studied systemically. through the study the influence of the shape, the proportion of the dust and the grade of sand to the workability and the mechanical property of self - compacting concrete, it is found that super fine mountain sand artifical sand are not suit to prepare low and middle strength self - compacting concrete, but when they are combined and the additive and assistant band material are used, c20 - c40 high performance self - compacting concrete is prepared ; the corresponding additive is developed to solve the delamination caused by the low proportion of banding material ; the evaluating system for the workability of low and middle strength self - compacting concrete is built ; the controlling method for production, construction and curing was set up. and the result of the research is applied into several projects

    通過分析特細山砂和機制砂的顆粒形態、粉末含量、顆粒級配等特性對自密實混凝土的工作性能和力學性能的影響，發現特細山砂、機制砂不宜單獨用於配製中低強度等級自密實混凝土，宜將特細山砂和機制砂進行合理復配，並選擇合適的外加劑和礦物摻合料，優化配合比設計，可生產c20 c40中低強度等級自密實高性能混凝土；研製開發出了具有高效減水、保塑、抗離析功能的外加劑，有效解決了中低強度等級自密實混凝土由於膠凝材料用量少而出現的離析、泌水問題；應用正交設計方法，對因素和水平進行合理選擇，確定了生產中低等級自密實混凝土的最優配合比；建立了中低強度等級自密實混凝土的工作性評價體系；提出了生產、施工及養護的質量控制技術方法。
  9. Directed by the adsorption theories, sepiolite was selected as micropore inorganic material and dodecanol was selected as pcm, and carried out the optimization of experimental parameters, such as selection of sepiolite minerals, sepiolite modification, absorption temperature, pcms solution concentration, stirring time, drying mode, dehydration of sepiolite. by the optimization, the best conditions on tsous preparation were achieved. measurement method of pcms exudation was established to estimate the exudation of pcm in tsous, the temperature self - operating effects and energy saving effects of tsous was also examined

    在以上微孔吸附理論研究基礎上，選用海泡石作為微孔無機材料、十二醇作為相變工質材料，對自調溫單元的制備工藝參數進行了優化研究，包括：海泡石原料的選擇、海泡石改性的影響、吸附溫度的選擇、 pcm有機溶液初始濃度的選擇、攪拌時間的確定、烘乾方式的選擇、海泡石含水量的確定，最終得到自調溫單元的最佳制備工藝。
分享友人
分享到 Line

分享到臉書