最初劑量 的英文怎麼說

中文拼音 [zuìchūjìliáng]
最初劑量 英文
initial dose
  • 最 : 副詞（表示某種屬性超過所有同類的人或事物） most; best; worst; first; very; least; above all; -est
  • 初 : Ⅰ名詞1 （開始的部分） at the beginning of; in the early part of 2 （姓氏） a surname Ⅱ助詞（附著...
  • 劑 : Ⅰ名詞1 （藥劑; 制劑） a pharmaceutical or other chemical preparation 2 （某些有化學作用的物品） a...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 最初 : prime; initial; first
  • 劑量 : [物理學] [醫學] dosage; dose; dosis劑量槽 dosage bunker; 劑量測定（法） dosimetry; health work; ...
  1. Abstract : this paper researches into the complex adhesive ， which was mainly made by the soy protein isolate ( spi ) and polyvinyl alcohol or polyvinyl acetate. different composition of protein and polymers can perform different characters, together with other ingredients. the factors, which are related to the first adhesive strength and adhesive strength, are mainly studied and discussed. the first adhesive strength of the complex adhesive is related to the content of spi, and the adhesive strength is related to the content of the complex adhesive. on the basis of the researching, we can make the plant fibre box for food in the future

    文摘:對大豆分離蛋白?聚乙烯醇、大豆分離蛋白?白乳膠復合膠粘劑進行了研究，採用不同混合比例及添加其他助劑，得到較好性能和可生物降解的復合膠粘劑，為製造一次性植物纖維快餐盒打下基礎.主要研究了影響這種復合膠粘劑粘接木塊的初粘力（剪切和拉伸強度）和粘接強度的因素，實驗表明： 9 . 2 %濃度的大豆分離蛋白的初粘力（剪切和拉伸強度）優於10 %濃度的聚乙烯醇膠和33 %濃度的白乳膠；大豆分離蛋白復合膠粘劑的初粘力主要與大豆分離蛋白含量有關，其最終粘接強度與膠液固含量正相關
  2. A preliminary approach to relation between the optimum dose field distribution of irradiation installation and arrangement of radiation source bar

    輻照裝置劑量場最佳分佈對源棒排布要求初探
  3. The influence of catalyst on the copolymerization of epoxy and cyanate was investigated, and the mechanism of their copolymerization was discussed. the catalyst can obviously accelerate the curing of the resin to decrease the curing temperature. the three kinds of reactions ( cyclotrimerization, co - reaction and polyetherification ) in their copolymerization are not simultneous and independent to each other. in the lack of cyanate functional group, the main structures are oxazoine and polyether structure in the cured resin, and the triazine ring structure is of miner importance

    研究了催化劑對環氧樹脂與氰酸酯樹脂的共聚固化反應行為的影響，並初步探索氰酸酯/環氧固化的反應歷程.研究表明，催化劑能明顯地促進其固化反應，降低固化溫度，縮短固化時間；氰酸酯與環氧共聚反應歷程是首先氰酸酯三聚反應生成三嗪環結構，然後三嗪環開環與環氧共聚反應，最後是未能參與共聚反應的環氧官能團在唑啉結構和三嗪環的催化下發生聚醚化反應；在氰酸酯官能團欠量的條件下，固化樹脂中主要是唑啉和聚醚結構，而三嗪環結構的含量很少
  4. And if we unite these them, we will get more advantages from them. this experiment made some prime lab research about the unition of the two ~, processes. it contents : 1 ) jar test of optimized coagulation : to determine the quantity of drug

    本試驗對強化混凝和粒狀活性炭吸附技術聯用的處理工藝作了初步試驗研究，試驗內容包括： 1 ）小試：通過杯罐試驗來確定對于不同濁度的湘江源水的混凝最佳劑投加量。
  5. ( 3 ) orange pigment could be oxidized with hydrogen peroxide to yellow pigment. concentration of h2o2 was proportional to creation of yellow pigment. the quantity of orange pigment was influenced by the nitrogen source of the culture medium

    （ 3 ）對橙色素進行了初步研究，橙色素可以氧化為黃色素，且氧化劑的濃度越大，黃色素生成率越高；氮源是影響橙色素產量的一個主要因素，以nh _ 4cl為氮源，確定其最適添加量為0 . 01 。
  6. The doctors can observe the relationship and geometry of the organs and the tumors, from the 3d model of the human body, which can help them create the therapy plan. the radiation dosimetry is built using monte carlo method. after we extract the iso - surfaces from the volume of the doses, the relationship between radiation doses and the cancer is represented on a 3d model, which is greatly helpful for the doctors to improve their therapy plan

    通過建立三維人體模型，可以幫助醫生直觀的觀察人體內部病灶及組織器官的形態位置尺寸，並獲得其量化指標，從而更加準確的制定治療計劃：根據初步的放療計劃，使用montecarlo方法建立模擬的放射劑量分佈數據場，再通過等值面提取方法獲得等劑量面，顯示並量化劑量分佈情況和病灶（靶區）的關系；根據模擬的結果對放療計劃進行適當修改，並最終獲得最佳的放射治療計劃。
  7. First determined to the comparatively succeed material prescription preliminarily through an orthogonal experiment, with this as a foundation, carried out only - factor experiment continuously. we have studied that the influence of various additive contents on material performance such as the soften temperature and the heat - bearing time, determined the best material prescription eventually

    首先通過正交試驗初步確定材料配方，以此為基礎繼續進行其他組分固定的單因素試驗，研究了各種添加劑含量對材料軟化點、耐熱時間等性能的影響，最終確定最佳的材料配方。
分享友人
分享到 Line

分享到臉書