最大聲增益 的英文怎麼說
中文拼音 [zuìdàshēngzēngyì]
最大聲增益
英文
maximum acoustic gain-
Based on our theoretical predictions, we find optimal splicing parameters on fsm - 30s fiber splicer for low loss joints between erbium doped fiber and other single mode fibers. we also experimentally demonstrate a novel three - stage erbium - doped fiber amplifier with high gain, low noise figure, and high output power. finally, a prototype of a gain - clamped fiber amplifier is obtained with high gain ( 26 db ), low noise figure ( 5. 3 db ), high output power ( 17 dbm ), and large bandwidth ( 31 nm )
文章研究了摻鉺光纖( edf )與其他光纖低損耗焊接問題,得到光纖熔接機低損耗熔接的最佳參數,這對摻鉺光纖放大器的科研生產具有一定的指導意義;研究了新型的三段級聯泵浦優配的摻鉺光纖放大器的優化光路結構,得到高增益,低噪聲,大輸出功率的摻鉺光纖放大器;最後研製成功高增益( 26db ) ,低噪聲( 5 . 3db ) ,大輸出功率( 17dbm ) ,寬帶( 31nm )增益箝制摻鉺光纖放大器樣機。In order to measure the characteristics of such semiconductor optical amplifier, we adopted a set of measurement system. this measurement system can be used to measure the characteristics of all kinds of active or inactive optical passive components. such device presents good polarization insensitivity ( < 0. 9db ), wide 3db bandwidth ( > 33nm ) at 0 - 200ma and different input signal light wavelength and power, the maximum fiber - to - fiber gain of 10db, lossless operation current of 50 - 75ma for different input signal light wavelength and power, large extinction ratio ( > 50db ) and lower noise figure ( nf ) ( < 8db )
與張瑞英博士一起,首次利用該種有源區結構制備出偏振不靈敏半導體光放大器,並在0 - 200ma注入電流范圍內獲得33nm的3db帶寬,在不同信號波長,不同信號功率0 - 200ma的注入電流范圍內,偏振相關損耗均《 0 . 9db ,在耦合差損為7db / facet的條件下,最大fiber - to - fiher增益達10db ,無損操作電流為50 - 70ma ,消光比達50db以上,而噪聲指數則低於8db ,最小可達4 . 6db 。4. according to the analyses of underwater acoustic channel and long - range remote control receiving system, we designed the long - range remote control receiver, including a low noise prefix - amplifier, a band pass filter and an auto - gain control circuit. finally, the analog part of the receiver is tested and the frequency response of this receiving system is obtained.
結合對水聲通道特性和遠程遙控接收系統的分析,進行了遠程遙控接收機的設計,包括接收機低噪聲前置放大器的設計、帶通濾波器電路的設計和集成以及自動增益控制電路的設計,最後對接收機模擬電路進行了調試。First please make sure the useful signal has very good snr before you input it to amplifiers chain, then you can calculate how much gain and nf you need to get the targeted signal amplitude and noise level, based on this you can choose the right components to design amplifiers chain
后才將其輸入放大器鏈,接著計算獲得目標信號振幅和噪聲水平所需的增益與nf的大小,最後根據這些數據選擇合適的器件設計放大器鏈路。This paper studies the design methods and techniques of the broadband lna. using negative feedback techniques and lossy match method, a broadband lna acceptable for sdr is presented. the measured results showed that over 30mhz ~ 3000mhz, the lna achieved a maximum noise figure of 2. 0db, a power gain of 22db with gain flatness of less than 2. 0db
本文最後對寬帶低噪聲放大器的設計方法進行了詳細探討,並運用負反饋技術和有損匹配的方法,研製了一種適合軟體無線電應用的寬帶低噪聲放大器,經測試,在30 3000mhz頻率范圍內,噪聲系數nf 2 . 0db ,增益g = 22db 2 . 0db 。Main features of my paper are as follows : 1. taking advantage of ( advance design system ) ads, one of the most powerful radio - frequency simulation tools, we mean to simulate and design lower - noise - amplifier ( lna ) for lowest noise coefficient and maximum gain as preparation for systematic simulation
本文的主要工作特色如下: 1 、用目前最流行的射頻模擬工具之一ads對低噪聲放大器進行模擬和設計,實現lna的最小噪聲系數和最大增益,同時為系統模擬奠定基礎。分享友人