有通氣孔模板 的英文怎麼說

中文拼音 [yǒutōngqìkǒngmóbǎn]
有通氣孔模板 英文
vented form
  • 有 : 有副詞[書面語] （表示整數之外再加零數）: 30 有 5 thirty-five; 10 有 5年 fifteen years
  • 通 : 通量詞（用於動作）
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 氣孔 : [礦物學] blowhole; [植物學] stoma; [動物學] spiracle; pore; stigma; [冶金學] gas hole; gas pocket; [建築] air hole
  • 模板 : [土] formwork; mould; shuttering; follow board; form board; match board; match plate; mother plat...
  1. By comparing the dry plate pressures drop and distributions of velocities simulated on single valve with those of double valves, it was found that there was intense turbulence in the flow fields around fixed - valve, there were eddy areas between valve side orifices and tray wall, there were eddies above the valves too, these led to the complex behaviors of gas perforating valve, these had a great effect on the gas - liquid mass transfer process. at the same time, in order to prevent the disadvantageous effect of gas between one valve with another on the gas - liquid mass transfer, it was very effective to change the fields of gas perforating valve by folding the edges of valve

    通過對數值模擬得出的單閥和雙閥塔板的干板壓降及流場速度分佈分析對比后發現，固定閥周圍流場存在較強的湍動，閥側孔與塔板壁面區域以及閥體的上方空間存在明顯的渦流區，使氣體穿閥后的行為變得復雜，並對氣液傳質過程產生重大影響；模擬結果表明，為防止和削弱固定閥間的對沖造成的「死區」對傳質帶來的不利影響，通過折邊來改變氣體的氣路是非常有效的，模擬值與實驗值基本得到吻合。
  2. This thesis work has researched the fabrication technics of photonic crystal defect waveguide with air - bridge structure and collecting waveguide ; suggested using uv - lithography and wet etching to fabricate traditional waveguide, after that, using eb - lithography and dry etching to fabricate photonic crystal holes, so can reduce the fabrication cost by a big range ; designed the moulding board, which can fabricate the air - bridge structure and is convenient for recognizing position in eb - lithography ; the structure consisted of traditional waveguides and etching grooves are fabricated on soi successfully, then an successful eb - lithography is realized on the structure, the defect waveguide collected with the traditional waveguide quite well ; used the etching grooves to do the sacrificial layer etching experiment, which grounded etching sacrificial layer by photonic crystal holes in next step

    提出採用紫外光刻工藝製作傳統波導結構之後，通過電子束曝光和干法刻蝕製作光子晶體小孔的工藝方案，大幅度減低了製作成本；設計出可形成空氣橋結構、並且適用於電子束曝光位置識別的光刻模板，在soi材料上成功製作出帶有空氣橋刻蝕預留槽以及接續光波導的結構，在該結構上成功實現了光子晶體帶隙波導的電子束曝光，帶隙波導與接續光波導位置接續良好；最後利用預留槽進行了刻蝕犧牲層的實驗，為下一步利用光子晶體小孔刻蝕犧牲層形成空氣橋結構打下了基礎。
  3. A theoretical model for purification of waste gas of low concentration in trickling biofilter was established with simplifying, the polyhole filter in the trickling biofilter to a parallel plat plates passage covered with biofilm

    摘要將生物膜滴濾塔內的多孔填料簡化?壁面覆蓋有生物膜的平行平板通道，建立了一個凈化低濃度有機廢氣的理論模型。
  4. Combined with the permeability and heat transfer properties of lamilloy configurations obtained by experiments, a one - dimensional porous wall thermal heat transfer model was applied to the analysis of the mass flow rate, and the overall cooling effectiveness of different lamilloys according to the pressure drop between the two sides

    摘要基於一維多孔材料內傳熱理論，建立層板冷卻的理論模型，應用由實驗獲得的各種層板結構的流阻和換熱特性，由層板兩側的壓差估算通過層板的冷氣流量和層板結構的冷卻有效性。
分享友人
分享到 Line

分享到臉書