末端測試 的英文怎麼說

中文拼音 [mòduāncèshì]
末端測試 英文
tag end test
  • 末 : Ⅰ名詞1 （東西的梢;盡頭） tip; terminal; end 2 （非根本、非重要的事物） nonessentials; minor detai...
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 末端 : end; terminus; terminatio; terminal; tail end; extremity末端棒 terminal bar; 末端朝上 endways
  • 測試 : test; testing; checkout; measurement
  1. According to the system technology require, adopting singlechip realize open loop digital control of hdclsm ; using v / f conversion and complex key - control method realize digital setting of system parameter, such as velocity ; using micro - stepping control insure the motor running more smoothly ; adopting debasing speed control method to eliminate the mechanical impact of distance termination effectively ; at the same time, analyzing main power circuits drive circuit and protect circuit of system, completing hardware design and facture and software programming and debugging ; at last, making a whole test in hybrid rotary step motor. the experiment result indicates that this control system reaches the qualities required and run smoothly also

    根據系統技術要求，採用單片機實現了混合式直流直線步進電動機的開環數字控制；利用v f變換和復合鍵控方法實現了系統轉速等參數的數字設定；利用細分控制技術保證了電機運行的平穩性，並進行了波形分析和理論研究；採用單片機軟體降速控制策略解決直線步進電機行程末端的機械沖擊問題；同時對主功率電路、驅動電路和系統保護電路進行了分析，完成了硬體設計、製作和軟體編程、調試，最後在混合式旋轉步進電動機上進行了全面測試。
  2. The experiment apparatus has been developed, which is based on software ( labview ) and hardware ( pci board ni 6024e ). the displacements and generative force at the tip of the ipmc actuators were measured with respect to the different voltages, frequents and various waveforms which include square, sinusoidal, and triangular wave

    實驗選取了不同電壓幅值，不同頻率的方波、三角波、正弦波三種波形作為電激勵信號，利用高速攝像記錄ipmc的位移變形，並通過力傳感器實測了ipmc試樣末端的輸出力。
  3. Sealing and sliding sealing rings, cutting tools, reamer tips, reamer heads, saw tips, clamping supports, inserts for bore - crowns, plates, tip inserts for measuring and testing devices, nozzles, lining bushings, milling inserts, cold rolls, drawing dies, powder pressing dies

    密封環和滑動密封環、切削工具、絞刀齒、絞刀頭、鋸齒、夾具、牙冠填充物、金屬板、測量和試驗儀器的頂端襯墊、噴嘴、襯套軸套、銑削襯墊、冷壓模具、沖模、粉末壓模。
  4. The cause of vacuum degree formation under groundwater table is discussed in the paper. the testing results show that vacuum degree above the groundwater table is produced directly by pumping air, and that vacuum degree below groundwater table is produced mainly by dewatering and by escaping of sealed air from the end of flexible pipe. based on the bernoulli equation, the limit lowering of groundwater table is analyzed, which is about 5 ~ 7m. the effective influence depth of vacuum preloading has relationship with pvds depth and can be more than 10m

    對地下水位線以下的真空度成因進行了分析，結果表明，地下水位線以下測到的真空度是由於測試軟管中水位下降或部分封存氣體從軟管末端逃逸引起的，與地下水位線以上的真空度由抽氣直接形成在成因上存在不同；根據伯努俐方程，對地下水位下降的極限深度進行了分析，得出真空預壓中地下水位的極限下降深度為5 7m ；對有效影響深度的分析結果表明，真空預壓的有效影響深度與塑料排水板的打設深度具備一定關系，有效影響深度可以超過10m 。
  5. Methods : this experiment used finite element analysis ( fen ) in the design of mesial and distal occlusal rest of distal - extension partial removable denture and to test the magnitude of stress and displacement of abutment teeth and soft tissue under the base when under the vertical force of two conditions

    方法：採用有限元法在末端游離缺損義齒的有限元模型上作遠中、近中（牙合）支托設計，分別在人工牙及修復后的牙列（包括義齒及基牙）上作垂直向加載，測試基牙及基托下軟組織的位移及應力值，通過測試結果作對比分析。
  6. Fibre optic interconnecting devices and passive components - basic test and measurement procedures - part 3 - 23 : examination and measurements ; fibre position relative to ferrule endface

    光纖互聯裝置和無源部件.基本試驗和測量步驟.第3 - 23部分:試驗和測量.與金屬箍末端有關的纖維位置
分享友人
分享到 Line

分享到臉書