材料彎曲 的英文怎麼說

中文拼音 [cáiliàowānqū]
材料彎曲 英文
warping material
  • 材 : 名詞1 （木料） timber 2 （泛指可以直接製成成品的東西; 材料） material 3 （供寫作或參考的資料） ma...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 彎 : Ⅰ形容詞（彎曲） curved; bent; crooked; flexuous; tortuous Ⅱ動詞1 （使彎曲） curved; bend; flex 2 ...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 材料 : 1. （原料） material 2. （資料） data; material 3. （適于做某種事的人才） makings; stuff
  1. Test method for flexure of glass material

    玻璃材料彎曲強度試驗方法
  2. Flexure property analysis of three - dimensional braided composite

    三維編織復合材料彎曲性能分析
  3. Experimental investigation on flexural fatigue behavior of plain weave glassfiber reinforced laminates

    玻璃纖維織物復合材料彎曲疲勞行為的試驗研究
  4. Test methods for bend testing of materials for ductility

    展延性材料彎曲試驗方法
  5. Textile glass - rovings - determination of flexural strength of rod composites

    棒狀復合材料彎曲強度的測定
  6. Concretes. individual properties of hydraulic machines for bending tests of hard materials

    混凝土.硬材料彎曲試驗用液壓機的特殊性能
  7. Flexural property testing for 2. 5d sio2 fiber - reinforced - sio2 composite

    石英纖維織物增強二氧化硅基復合材料彎曲性能測試研究
  8. The rigidity and strength performance such as tension bend, torsion of composite laminated plates are calculated by use of classical lamination theory, and then analyses the experiment methods for rigidity and strength of laminate in detail, the comparison of theoretical analysis and experimental result shows good consistent, which indicate that the theoretical analysis and experimental method presented there is applicable for design and manufacture of military medical shelter laminate. in addition, theoretical analysis is taken for heat preservation and insulation performance of the laminate material by use of stable plate heat conduction method

    採用經典迭層理論，計算了軍用醫療方艙復合夾層大板材料的拉伸、彎曲及扭轉等剛強度性能，由此深入研究了夾層大板材料彎曲剛強度性能試驗方法，對理論分析進行了試驗驗證，結果表明該課題提出的理論分析和試驗方法適于軍用醫療方艙鋁塑復合夾層大板力學分析，對軍用醫療方艙鋁-聚氨酯-鋁復合夾層大板的力學結構設計和製造具有重要的應用價值。
  9. Calculation and experimental research on bending performance of glass fiber reinforced plastics rubber sandwich beams

    橡膠夾層復合材料彎曲性能計算與實驗
  10. Standard test method for bending fatigue testing for copper - alloy spring materials

    銅合金彈簧材料彎曲疲勞試驗的標準試驗方法
  11. On the ground of researching of processing property of 3266 resins, the influence of tackifier contents on the flexural strength, shearing strength, and modulus of composites ( 3186 carbon cloth / 3266 resin and 827 carbon cloths / 3266 resin ) were also studied

    摘要在對3266樹脂工藝性研究的基礎上，研究了定型劑含量對3186緞紋、 827單向碳布3266樹脂基復合材料彎曲強度、層間剪切強度和模量的影響。
  12. When the tidy of material is not enough, the sawing side will bend with the bend arc of material

    材料平整度不足，鋸切面會隨著材料彎曲的弧度而彎曲，如圖。
  13. Time - temperature dependence of flexural strength of glass fiber reinforced plastics

    玻璃纖維增強樹脂基復合材料彎曲強度時間溫度相關性
  14. Then tension and bending strength reach to maximum when the wood flour content is 40 %. the addition of coupling agent ( maleic - anhydried - modified polystyrene, maps ) can improve these properties described above

    當添加20的偶聯劑時，木粉含量為40和50的復合材料的吸水量減少了一倍；存儲模量高於未加偶聯劑的復合材料；彎曲強度和拉伸強度分別增加了10和40以上。
  15. Plastics and composites. determination of the bending fatigue properties. part 3 : three - point bending test on unsecured test pieces

    塑料製品及復合材料.彎曲疲勞特性的測定.第3部分:不固定試件的三點式彎曲試驗
  16. Concretes. common characteristics of hydraulic machines for compression, bending, and tension testing of hard materials

    混凝土.硬材料彎曲.壓縮和拉力試驗用液壓機的一般特性
  17. Testing method for flexural strength of continuous fiber - reinforced ceramic matrix composites

    連續纖維增強陶瓷基質復合材料彎曲強度的試驗方法
  18. Plastics and composites. determination of the bending fatigue properties. part 1 : general principles

    塑料製品及復合材料.彎曲疲勞特性的測定.第1部分:一般原則
  19. Experimental study of notch flexural strength of tic al2o3 ceramics and prediction of its probability distribution

    3復合陶瓷材料彎曲切口強度及其概率分佈的預測
  20. Bend test pieces for metallic materials

    金屬材料彎曲試驗用試件
分享友人
分享到 Line

分享到臉書