板件拉延 的英文怎麼說
中文拼音 [bǎnjiànlāyán]
板件拉延
英文
plane drawing-
Here the hsc of sompa is achieved through adding super - effective water reducer, fined slag and silicon fume, and decreasing the water / cement ratio. by varying the area ( spacing ) of tension bars, compressive bars, vertical links and distribution steel and embedding steel fiber and polypropylene fiber we try to improve the behaviors of reinforced high performance concrete one - way spanning slabs in bending, so that its ductility be greater than 5. with the same arrangement of steel the width of bending member is varied to observe the effect of the width / depth ratio on the ultimate compressive strain of concrete
通過變化受拉筋含筋率和受壓筋、箍筋（鉤筋、分佈筋）含量，或摻加纖維使之成為鋼纖維高強混凝土（ sfrhsc ）和聚丙烯纖維高強混凝土（ pfrhsc ） ，對高強混凝土雙筋截面梁、板的受彎性能進行了試驗研究，試圖改善高強混凝土受彎構件的延性，使其延性比大於5 ；並在相同配筋情況下，通過變化截面寬度，研究了高強混凝土受彎構件的寬高比對壓區混凝土極限應變的影響；並對試驗構件的裂縫發展情況進行了觀測。This paper referred to the massive domestic and foreign technical material, elaborated in the sheet forming value simulation theory essential technology in detail, points out when analysis sheet forming question should use the big distortion ball plasticity fem and introduce the application characteristic and the function summarizes of the sheet forming simulation software dynaform. secondly, analyzed the cover forming characteristic, simultaneously introduced the influence cover forming factor in detail : such as ramming direction, the craft addendum surface and the material pressing surface, the radius of convex - concave mold, draw bead, pressure strength, blank size and craft margin and so on. and simulates many typical automobiles cover panel with software : such lateral board, back taillight pedestal and storage cover
其次，分析了覆蓋件成形的特點和要求，同時詳細介紹了影響覆蓋件成形的因素如沖壓方向、工藝補充面和壓料面、凸凹模圓角、拉延筋、壓邊力、坯料尺寸和工藝切口等，並用數值模擬軟體對多個典型的汽車覆蓋件汽車后側圍板、后燈座以及轎車后備箱蓋的沖壓成形情況進行模擬，用模擬結果優化拉延工藝方案，比較了內覆蓋件和外覆蓋件在成形特點和要求的一些異同點，以及常見的起皺、拉裂和回彈、成形不足等缺陷的產生機理和相應對策，重點介紹工藝補充面和壓料面的設計及優化方法，因為拉延是沖壓工藝的關鍵工序，而工藝補充面和壓料面的設計是拉延工序的關鍵，對消除缺陷至關重要。This paper take the junction panel of the front reinforced beam in the back automobile floor for the example, introduces the drawing die design process, which proves this method simplified the design process, enhanced the rated capacity
本文以汽車后地板前加強梁左右連接板為例介紹了汽車覆蓋件拉延模具設計，經過實踐應用，證明該方法簡化了設計過程，提高了設計效率。In the last chapter of this thesis, we introduce two kinds of sheet metal parts. one is forming part which require very accurate prediction of blank shape, the other is drawing part which need just approximate prediction of blank shape. we apply the scale coefficient method to predict the blank shape of these two kinds of sheet metal parts
文中最後一章，給出了兩類典型的沖壓零件，一類是落料后直接成形的零件，該類零件初始板料的形狀及尺寸要求非常精確;另一類是兩次拉延成形的零件，這類零件的初始板料要求適合的形狀及尺寸即可。分享友人