板尺 的英文怎麼說

中文拼音 [bǎnchǐ]
板尺 英文
board foot
  • : Ⅰ名詞1 (片狀硬物體) board; plank; plate 2 (專指店鋪的門板) shutter 3 [音樂] (打拍子的樂器) ...
  • : 尺名詞[音樂] (中國民族音樂音階上的一級 樂譜上用做記音符號 參看「工尺」) a note of the scale in ...
  1. Metal working - chequered plates - dimensions and tolerances

    金屬加工.網紋鋼.寸和公差
  2. Medico - surgical equipment. implants for surgery. rough surface diaphysis plates made of stainless steel. dimensional and surface characteristics

    外科醫療設備.外科植入物.不銹鋼粗糙表面骨幹.寸和表面特性
  3. Concrete ground plates for surface boxes ; dimensions, types

    地面混凝土箱涵的混凝土地.寸和類型
  4. Tank trucks ; grounding plate, dimensions

    槽罐車.接地
  5. Particle boards. dimensional characteristics

    刨花.寸特性
  6. Sizes of paper and board - specification for a and b series of trimmed sizes of writing paper and certain classes of printed matters

    紙和紙板尺寸.第1部分:書寫紙和某些印刷品的a系列和b系列切邊寸規范
  7. Forestry machinery - portable brush cutters and grass trimmers - cutting attachment guard dimensions

    林業機械.便攜式灌木切割機和剪草器.切割附件護板尺
  8. Driving plates. dimensions

    撥動夾.
  9. Therefore, under the certain condition of the profile of open channel, the size of long and narrow plate and installation, the flux can be achieved from the equal flux curve if the opening angle of the plate and water depth in front of the plate are accurately determined

    在確定渠斷面、細長板尺寸以及安裝布置條件下,只要準確測得細長開啟角與前水深,便可利用等流量線圖得知此時的流量。
  10. Translucent glass fibre reinforced ribbed polyester sheets. dimensional characteristics

    屋頂和護.塑料.玻璃纖維增強半透明聚酯加肋.寸特性
  11. Wood wool slabs. measurements of dimensions and edge squereness

    木絲.寸與邊的垂直度的測定
  12. Photography - glass plates - dimensions

    攝影.玻璃.
  13. Roofing. general. dimensional inspection of corrugated sheets

    .總則.波紋板尺寸檢驗
  14. Terminal block for telecommunication systems ; dimensions

    通信設備用端子.
  15. No endplate of reasonable size will prevent tip flow.

    沒有一個合適的端板尺寸將會阻止翼根繞流。
  16. Glued laminated timber - sizes - permissible deviations ; german version en 390 : 1994

    膠合木.寸充許偏差
  17. Veneer plywood for general use. dimensions and tolerances

    一般用途飾面膠合.寸和公差
  18. Panel mounting racks for electronics equipments ; racks and panels, dimensions

    電子設備的面式安裝架.架和面.
  19. The result shows that the dimension ' s decreasing of polar plate can make the level of stress and strain decrease during hydrobulging and the spherial vessels with smaller ovality can gained

    結果表明:在桔瓣數目一定的情況下,減少極板尺寸可以降低多而殼體成形過程中應力應變水平,並得到不圓度小的球形容器。
  20. Given the thermal physical parameters of the envelops and the weather data, the above two parameters are determined by the following system design parameters : radiant panel dimension, radiant panel location and radiant panel layout style ( center or peripheral ). based on the thermal net model, digital analysis of the energy consumption and thermal environment are carried out to the several representative spaces under different design parameters, through which the relations of the heating load to the design parameters are obtained and can be a reference in the practical system design

    對于給定圍護結構熱物性參數和室外氣候參數的條件下,室內平均輻射溫度和室內空氣溫度的大小取決于系統的設計參數:輻射的布置方式(周邊布置和中心布置) 、輻射板尺寸和輻射鋪設位置。基於熱網模型,利用matlab軟體編程對採暖空間在不同設計參數下室內的熱環境和能耗進行數值分析,得出了低溫熱水地輻射採暖系統的性能和能耗指標隨這些參數變化的規律,從而為低溫熱水地輻射採暖系統的優化設計提供了參考。
分享友人