板極調制 的英文怎麼說

中文拼音 [bǎnjídiàozhì]
板極調制 英文
plate modulation
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  1. Thanks to our large and well - equipped japanese open kitchen in town and the experienced chefs led by mr ito shigeru, our new chef de cuisine - japanese. with which customers can enjoy lots of exquisite and delicious food cooked in different japanese styles and methods such as sushi, sashimi, sabu sabu, teppanyaki, robaytayaki, tenpura and other hot dishes. chef recommendations include baby lobster sashimi, urchin egg custard, king prawn, beef tenderloin and assorted vegetables with teppanyaki sauce, crab congee with sweet corn and crab roe, okinawan sweet potato cheese cake, tofu cheese cake and lively made red bean pancake dora - yaki

    全新的日本料理晚市放題特別由極富經驗的日籍名廚伊滕茂師傅親自主理，並以地道的日本烹調技巧包括壽司、刺身、火鍋、燉煮、燒烤、清蒸及油炸等，為大家即席炮製各式用料名貴又精緻可口的日本美食，重點主打深海龍蝦仔刺身、日式火鍋、日式海膽蒸蛋、鐵板燒大蝦、牛肉及野菜、甜蟹粥、蕃薯芝士餅、豆腐芝士餅及即制紅豆班戟等，真正和風美食多逾50款。
  2. Though much progress has been achieved in previous study, there still remains a lot to be studied and perfected. the thesis is devoted to study on the multi - ribbed slab wall, the main bearing member in mrss, including its mechanism, failure mode, aseismic capability, mechanical models, ultimate bearing capacity and aseismic design based on control. the paper mainly accomplished such work as follows : 1 ) based on test research on multi - ribbed slab wall, the paper proposed the member ' s failure modes under horizontal loads, analyzed the co - performance between the inner frame and the infilled silica bricks and that between the slab and the outer frame, discussed the wall ' s bearing capacity, rigidity, deformation, ductility and energy dissipation ability in different modes, and put forward a simplified mechanical model of the slab wall under vertical loads

    本文針對密肋壁板結構的主要受力構件? ?密肋復合墻體為研究對象，就其受力機理、破壞模式、抗震性能、三階段力學模型、極限承載能力以及基於控制的抗震設計方法等進行了較為詳細的研究，完成的主要工作有： 1 ）通過對密肋復合墻體在水平低周反復荷載和單調荷載作用下的試驗研究，提出了墻體的主要破壞模式；分析了框格與內部填充砌塊、墻板與外框的共同工作的受力特點；探討了不同破壞模式情況下墻體的承載能力、剛度、變形、延性、耗能等抗震性能，並給出了豎向荷載作用下密肋復合墻體的簡化力學模型。
  3. The consumption of electrical energy of electrically calcined furnace during calcining anthracite is studied by adjusting the length of the top electrode, the flue damper and changing the release direction of removed dust produced from charging system of electrically calcined furnace

    摘要根據電?爐?燒無煙煤的工藝原理，通過調整上部電極長度、煙道閘板及改變電?無煙煤前上料系統通風除塵灰的排放方向等工藝控制方法，對電?無煙煤電耗進行研究。
  4. Firstly using the calculated cutting contour to cut the drawing part, then flange on the flanging mould, and then check the error for flanging part. try - out the part until it is correct. it is shown that the error of calculated cutting contour is in the range of 1mm through compared it with the correct contour

    本文將實際調試出的合格零件的修邊線與採用誤差修正法計算所得的修邊線進行對比，其誤差均在1mm范圍內，對于型面極其復雜的翻邊零件，如后地板前板，其修邊誤差也可控制在3mm范圍內，這就有效地減少了汽車覆蓋件的修邊、翻邊調試次數和周期。
  5. In the electrostatic force closed - loop plan, using the inertia mass of saw accelerometer as one board of the differential capacity, as it got the electrostatic force producer

    在靜電力平衡方案中，直接利用saw加速度計慣性質量作為差動式電容的一個極板，組成靜電力發生器，並利用脈寬調制反饋力方案解決了靜電力發生器非線性的難題。
  6. On basis of numerical simulation, the optimized weling technological has been vadidated and adjusted by plane test, results show that residual stress of both ends welded in advance can be decreased by the interspace welded later, and decreasing effect is the most obvious in the 50mm range of the interspace ; for local heating, it is 60mm from the edge of heated area to decrease residual stress

    通過平板試驗得到了分段焊與局部加熱合理工藝參數，並在此基礎上，對轉輪的焊接殘余應力場進行了調整與控制，使葉片出水邊危險區域附近產生了較大的殘余壓應力，且轉輪整體的殘余應力水平低於轉輪材料屈服極限的三分之一。
分享友人
分享到 Line

分享到臉書