板翹曲 的英文怎麼說

中文拼音 [bǎnqiáoqū]
板翹曲 英文
curling of slab
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 翹 : 翹動詞（一頭向上仰起） stick [hold] up ; bend [turn] upwards; curl up
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  1. Her chipper sound, bobbish melody, and jocose lyric, her innocent manner while she hugging her child and playing with her child like playing a seesaw, mixed with the creaky laugh of her child together, poppled in this small adobe

    她爽朗的聲音，快活的曲調，詼諧的歌詞，摟著孩子像玩翹翹板似的搖上搖下的天真的神態，和孩子嘰嘰嘎嘎的笑聲溶在一起，在這小土房裡蕩漾。
  2. Simulation analysis of the lengthways warp of truck carling outside board

    卡車縱梁外板縱向翹曲的模擬分析
  3. Twisting arises in boards through the presence of spiral or interlocking grain.

    翹曲多發生在螺旋或交錯紋理的板材中。
  4. Method to flatten pcb by warp twist tool plates

    印製電路板翹曲弓形的模具整平法
  5. Analytical and fem simulation of the front end bending in asymmetrical hot plate rolling

    非對稱板帶熱軋頭部翹曲的分析與有限元模擬
  6. The link should be formed steel plate, plate edge, no burr hole ; a joint warping, used to be calibrated to prevent injury and friction, the friction surface to ensure close

    連接處的鋼板或型鋼應平整，板邊、孔邊無毛刺；接頭處有翹曲、變形必須進行校正，並防止損傷摩擦面，保證摩擦面緊貼。
  7. Test methods of platness for printed boards

    印製板翹曲度測試方法
  8. In actual car service of such batteries, the two outside positive plates were generally buckled and shorting through the adjacent separators.

    這種蓄電池在實際車輛使用過程中，一般都是外面兩片正極板翹曲，穿透相鄰的隔板而造成短路。
  9. The logs should be cut from larger pieces and have alternate strips turned end to end so that warping tendency will be resisted.

    加工時，應先將大木料裁成板，然後把相鄰兩塊紋理相反地排列膠合起來，這樣可以防止翹曲變形。
  10. Calculation of thermal warping stresses in cement concrete pavement slabs

    水泥混凝土路面板溫度翹曲應力
  11. Cause analysis of tinplate warp and our countermeasures

    寶鋼鍍錫板翹曲原因分析與對策
  12. Buckling of plate

    板的翹曲
  13. After 20 days at 450 or 1 day at 500, the u3si2 particles cracked and fragmented, there were a lot of cracks in al - matrix and reacted areas, there were also a lot of holes in the meat. the meat lost its continuity and perfection, and departed from clad. above 450 the volume fraction of the al - matrix and the u3si2 decreased and produced u ( al, si ) 3 in the meat, u3si2 particles invaded to clad

    在450熱循環20天後、 500熱循環1天後，燃料板的厚度變化一般0 . 04mm ，燃料板的翹曲現象嚴重； u _ 3si _ 2顆粒開裂及破碎，基體中產生大量的裂縫，反應層也存在大量的裂紋及孔洞，芯體已失去連續性、完整性，並且與包殼脫開。
  14. Cause of multilayer printed board ' s warp and the countermeasure

    多層印製電路板翹曲成因與對策
  15. The results of the limited element analysis and experiment study confirms that both the resisting ended batten and using angle batten in place of plate one could make the laterally stiffness of such member more strong. that maybe provides somewhat practical benefits for designing the twin - wall truss

    本文還通過矩陣分析法和模擬試驗研究，證實了端綴板的存在對抵抗側向屈曲有明顯提高；而選用角鋼代替綴板材料相對于板形板，有助於提高構件的側移剛度和翹扭轉剛度，這對于單軸對稱綴板柱的設計也具有一定的實用價值。
  16. Experimental research of warpage of hdpe injection molded plate

    高密度聚乙烯平板翹曲變形實驗研究
  17. The defects of dehylogenation, deformation and poor waterproof can be overcomed or improved by the accession of fly ash and other composite admixture. better experimental results can be obtained by a lot of experiments

    但這類材質的板材防水性能比較差，表面吸濕后出現返鹵返霜、翹曲變形等現象，嚴重影響其裝飾性能和應用范圍。
  18. Plasma cutting thin plate special pressing unit : as cutting thin plate, due to the plate wrpping and putting not to steady, the worpiece cause cutting quality to go down even scrapped

    在切割薄板時，板材的翹曲和放置不穩定會造成切割工件質量下降甚至報廢。
  19. Camber of sheet

    鋼板的翹曲缺陷
  20. Collection of from plate should be done before use, do not use deformed and can ' t repair form plate, and abandon bolt hole should be made smoothly

    4模板使用前應進行選材，不能使用變形翹曲且無法修復的模板，廢棄螺栓孔修補平整。
分享友人
分享到 Line

分享到臉書