柱函數 的英文怎麼說

中文拼音 [zhùhánshǔ]
柱函數 英文
cylindrical functions
  • 函 : 名詞1. [書面語] （匣; 封套） case; envelope 2. （信件） letter 3. （姓氏） a surname
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 函數 : [數學] function函數計算機 function computer; 函數計算器 function calculator; 函數運算 functional operation
  1. This paper analyses the coupling wastage in columniform wave guide gas laser, and gives the function between the coupling wastage of laser guide modulo eh11 and the position and radius of reflector

    摘要分析了圓柱形波導氣體激光器中的耦合損耗，給出了最低階波導模eh11的耦合損耗與反射鏡位置、曲率半徑的函數關系。
  2. Application of r - function theory to the problem of elastic torsion with trapezium sections

    函數理論在梯形截面柱彈性扭轉問題中的應用
  3. According to eigenvalue equation ( general formula ) of the energy method of the plane steel frame structure stability, and considering the restriction of the end of the column of the main steel frame and function of deflection curve gained from the differential balance equation general resolution, we get the equation for calculating the length coefficient of the main frame structure stability of the steel arch gate and the resolutions are also given

    根據平面剛架穩定性能量法特徵值方程（通式） ，考慮弧形鋼閘門主框架柱的柱端約束的特殊情況，求出撓曲線函數（試解函數）通解，得到弧形鋼閘門主框架柱穩定性計算長度系數方程。其中弧門主框架主橫梁式形框架的臨界荷載比較現行規范推薦的有限元法簡單方便、結果精確及物理概念明確等優點。
  4. On the linear extreme of bergman space on polydisc

    2中多圓柱上函數空間上的極值問題
  5. Using the vector potential, the expression for calculating inductance of air - cored solenoid coil is derived in the dissertation. and the calculating methods of function t in the calculating expression are given for the convenience of the calculation of inductance while the precision is not strictly requested

    利用矢量磁位a直接推導出了通電空心圓柱線圈電感的計算表達式，給出了求解計算式中函數t的計算方法，以方便精度要求不高時的電感計算。
  6. Gle is a library package of c functions that draw extruded surfaces, including surfaces of revolution, sweeps, tubes, polycones, polycylinders and helicoids

    Gle是一個c函數庫包，它能繪制突出的表面，包括旋轉表面，伸展表面，管狀，多角體，多柱體和螺旋面。
  7. Mathieu function is the base of field theory analysis in elliptical cylinder coordinate system. so, firstly, detail investigation has been given about the problem of numerical analysis of matheiu functions, based on the predecessor ' s contribution, an improved faster algorithm of numerical analysis and confirmation algorithm of matheiu functions has been presented

    Mathieu函數是橢圓柱坐標系統下場論分析的基礎，因此本文首先對mathieu函數的數值計算問題進行了詳細研究，並在前人基礎上完善並進一步改進了目前被認為較為可行的數值演算法，並提出了驗證演算法。
  8. The net collocation point method with spline function is proposed to derive the formulation system of stochastic buckling analysis for cylinderic shells under various boundary conditions

    提出了樣條函數的網狀配點法，推導了不同邊界條件下圓柱殼屈曲的隨機分析公式系統。
  9. The program is applied to simulate the procedure of the upsetting, and the influence of size coefficient and weight function on the calculation results are also analyzed

    採用編制的程序以圓柱體的鐓粗過程為例，分析了尺寸因子、權函數等對計算結果的影響。
  10. By analysis of the transfer function and modal shape, we can draw a conclusion that this system is different from the common frame structure and even different from other types of structure with special - shaped columns. so the necessity of the studying has been verified

    通過對傳遞函數的分析以及對模態振型的回歸計算，找到了該結構體系由於其特殊的施工方式和構造措施與一般框架結構體系及異形柱填充墻體系相比所具有的特點。
  11. 4. choosing the reasonable deflection curve function. according to the energy method and the constrained condition of column end of the steel arch gate, the article presents a practical calculating formula for the stability of the main frame structure of the steel arch gate

    選擇合理的撓曲線函數（試解函數） ，根據能量法及弧門柱端約束條件，提出弧形鋼閘門主框架（平面鋼框架）穩定性計算的實用解析計算公式，並根據影響弧門主框架穩定性的因素對該公式進行修正。
  12. Based on apdl, the design language of finite element analysis software ansys, and visual c + +, the software on acoustics design of underwater cylindrical shell structure is developed. when input parameter of the cylindrical shell in the interface redeveloped in this paper, the software execute the batch file of apdl in the vc process to establish the finite element modal and carry out the analysis, the analysis result and the vibration mode can also be displayed. furthermore, the software has been developed to process the acoustics optimization design of the finite cylindrical shell with stiffener in appointed frequency range

    本論文從便於工程實際應用出發，對使用有限元分析軟體進行二次開發以方便結構振動分析及改進結構設計的方法和過程進行了研究，在此基礎上對水下航行器圓柱殼體的結構聲學特性進行了分析，在指定頻率區間，對結構以振動輻射聲功率級為目標函數進行了部分參數的結構優化設計，與此同時，為了方便有限元分析軟體的使用和簡化設計過程中大量重復的工作，利用ansys提供的參數化設計語言apdl （ ansysparametricdesignlanguage ）結合vc對有限元軟體ansys進行了二次開發，形成了一體化的水下圓柱殼體結構聲學設計軟體。
  13. Using the given inductance expression and calculating tables can rapidly and expediently calculate the inductance of the coil. and the gained result has higher precision, which completely satisfies the requirement of the general engineering application

    利用本論文所給的表達式和函數計算表能快速、方便地求解空心圓柱線圈的電感，而所得結果精度較高，可以滿足一般工程應用的需求。
  14. Steel frame with welding joint easily occur brittle collapse because of having a low ductility at joints then ， a semi - rigid connected steel frame has large the energy absorption capacity which can resist dynamic loads and the using steel qualities of bracing system and joints are small so adopting a semi - rigid jointed steel frame is economical and stable but for semi - rigid connections are complex and variable ， in conventional analysis and design of steel structures ， it is usually assumed that the connections between columns and beams are either rigid or pinned the analysis of steel frames adopting the assumption can simplify the procedure of analysis and design ， but cannot precisely reflect structural practical circumstance and the errors of calculating results are large ， even ， get incorrect conclusions semi - rigid connection was referred to in chinese code for design of steel structures ( 2001 ， 10 ) ， however ， it isn ’ t specified how to apply semi - rigid joints in design in fact it cannot be carry out the purpose of the paper give a calculating method that accords practical engineering and easily put into effect worthwhile it is going to promote the development of semi - rigid jointed steel frame in design and heighten structural stability in the paper ， at first some commonly employed methods for the modeling of connection behavior are introduced richard abbott function modeling of connection is adopted for extended end plate bolted connection by the 34 test data comparing to regression analysis indicate richard - abbott function modeling of connection represents an excellent fit to test data then after a semi - rigid joint behavior can be modeled as a finite stiffness rotation spring ， base on rotation and displacement equation derive the element stiffness matrixes with semi - rigid connections where the effects ofj ointed flexibility geometric non - linearity and shear forces in the connection deformations have been considered in and fixed - end forces are modified finally, a program for calculating semi - rigid with incremental - iterative method has been

    本文的目的就是為半剛性連接鋼框架的設計提供一種既符合工程實際又簡便易行的計算方法，供規范使用過程的補充、延伸或參考；同時，也將促進半剛性連接鋼框架設計技術的發展，為提高結構安全性能、節省工程成本發揮應有的作用。本文首先介紹了常見的幾種應用較為廣泛的樑柱連接彎矩轉角關系模型，在分析比較的基礎上，選用richard ? abbott函數模型作為外伸端板連接彎矩轉角關系模型，通過對34個外伸端板連接的實驗數據與回歸分析得到的參數比較可知，經回歸分析得到的此模型參數與實驗數據符合較好。然後用彈簧表徵連接點的轉動剛度，根據梁的轉角位移方程推導出半剛性連接的剛度矩陣，在單元剛度矩陣中考慮了節點柔性、幾何非線性和剪切變形的影響，並對固端力進行了修正，最後用增量迭代法編制有限元程序進行計算和分析。
  15. The fma need the high order hankel function, in chapter 3 the algorithm of calculating the high order hankel function of the second kind is discussed. because of the low effectivity and unsteadiness to use the recursive algorithm to calculate the high order hankel function of the second kind, the paper introduces a kind of new fast algorithm to solve the problem. the worked result indicates : the new fast algorithm is a kind of precise algorithm

    由於快速多極子法計算中要用到高階漢克爾函數，在第三章中，主要針對利用遞推演算法求解高階漢克爾函數時速度較慢和可能存在不穩定的問題，給出一種快速計算高階漢克爾函數方法，最後給出了用快速多極子法計算的四個導體柱體散射截面。
  16. Using databases of protein structures, it is possible to construct histograms of hydrophobicity as a function of the distance from the center of the protein

    利用蛋白質結構的數據可以構建疏水性的柱狀圖，作為蛋白質中心以外距離的函數。
  17. A class of exact solutions of the dirac equation are obtained for an electron in the electromagnetic field of a wave guide formed by two pairs of hyperbolic cylinders

    摘要研究了位於由兩對雙曲柱面構成的波導管電磁場里的單電子的性質，得到了單電子在場中狄拉克方程的新一類精確解；計算了極化算符的本徵函數。
  18. In this thesis, based on related previous references, using the non - fourier law of heat conduction, applying the image method, expand method of wave function, multiple scattering of thermal waves in materials with subsurface defects are investigated. our research works are concretely as following

    本文在分析了國內外相關文獻的基礎上，基於非傅里葉熱傳導波動方程，採用鏡像方法和波函數展開法，研究了固體介質中亞表面圓柱缺陷和球形缺陷對熱波的多重散射問題。
  19. Another mode of the total t matrix is derivated from the integral equation. finally the calculation result of two dielectric cylinders pro ves the effectiveness of windowed function and the correctness of the expression of the total t - matrix. windowed function is also applied into fma, which can accelerate the computation speed of the fma

    另外還從積分方程出發，推出了遞推了矩陣法的總體t矩陣的另一種表達形式，最後計算了兩個不同介質圓柱體的散射場，證明了引入窗函數的有效性、推出的總體了矩陣表達式的正確性。
  20. In chapter two, we first give the condition of generalized wavelets on l2 ( x ) by using the gelfand transform, where x = r + r denotes the underlying manifold of square integrable polyradial functions on the heisenberg group hn. then, we establish the theory of generalized wavelet transform and generalized wavelet packet transform on it

    在第二章中，我們利用gelfand變換刻畫了海森堡群h _ n上平方可積柱徑向函數空間的基礎流形laguerre超群x = r _ + ~ n r上的廣義小波，討論了該超群上的廣義小波變換與廣義小波包變換
分享友人
分享到 Line

分享到臉書