柱連接板 的英文怎麼說

中文拼音 [zhùliánjiēbǎn]
柱連接板 英文
ansatzstueck saeule
  • 連 : Ⅰ動詞1 （連接） link; join; connect 2 （連累） involve （in trouble）; implicate 3 [方言] （縫） ...
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 連接 : connect; fit together; link; marry; mate; joint; association trail; linkage; concatenate; concate...
  1. From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints

    採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。
  2. 3 use the doweling plus the glue to fix the baluster and straight step together

    3用木削加乳白膠把小柱和踏板連接牢固。
  3. The main components of the latter are multi - rib sandwich panels, including floor slabs and wall slabs. reinforced concrete conformation columns are set where the longitudinal walls and latitudinal walls intersect and copulative beams are set where floor slabs and wall slabs intersect. they play a role of linking and transferring loads, bearing a small part of loads at the same time

    無骨架體系的主要承重構件是密肋夾芯板（包括樓板和墻板） ，縱、橫墻相交處設鋼筋混凝土構造（連接）柱，墻板和樓板相交處設連系（圈）梁，連系梁和柱主要起連接和傳遞荷載作用，也承擔少部分荷載。
  4. Based on the numerical simulation and accuracy analysis to previous slab ' s test with the ansys program, the study of composite wall, with various detail design under potential load action respectively or jointly is carried on and the wall ' s atress behavior and failure mode is obtained, also the influence to wall ' s stiffness and bearing capacity by kinds of factors, including wall ' s shear span ratio, member ' s section, bar arrangement, etc. based on the hammer blow test and stiffness test, a 1 / 3 scale ten - bay model ' s modality parameter and elastic deformation characteristic is analyzed

    在對密肋復合墻板運用ansys ~ （ （ ? ） ）程序進行數值模擬、分析驗證的基礎上，對典型組合墻體在不同連接構造和不同荷載效應組合作用下的受力形態和破壞模式進行研究；計算分析了復合墻體剪跨比、邊框柱截面尺寸、邊框柱配筋大小以及墻板內肋梁肋柱配筋等諸多因素對密肋復合墻體承載力及剛度的影響，得出其變化規律。
  5. Steel moment - resisting frames with welded beam - to - column connections were traditionally regarded as having excellent performance, and widely adopted in steel constructions, but this opinion changed after the 1994 northrige earthquake and the 1995 hyogoken - nanbu earthquake. these earthquakes also arouse engineers to resurvey the behavior of end - plate connections

    傳統觀點認為，樑柱焊接剛性連接具有較好的抗震性能，因此在工程中得到了廣泛地應用，但1994年的northrige地震和1995年的阪神地震改變了這種傳統觀點，這兩次地震也引起了工程技術人員對端板連接的再審視。
  6. The present findings of semi - rigid connections, the method for design of beam - to - column connections in the codes from china and other countries, and the character about semi - rigid connections, were briefly introduced in this paper. the simulated method of the m - r relation curve of semi - rigid connections, the computing equations about the initial stiffness and moment capacities of two kinds of top - seat angle connections, with and without double web - angle, were discussed

    本文簡要地介紹了半剛性節點的研究現狀、各國規范樑柱連接的設計計算內容和方法、樑柱連接的類型和半剛性連接的特性，探討了頂、底角鋼、頂、底角鋼帶雙腹板角鋼兩種半剛性連接的m - _ r特徵曲線及其擬合方法，頂底角鋼連接、帶雙腹板頂底角鋼連接初始剛度以及彎矩承載力的計算公式。
  7. The main popular theoretical method adopted to study end - plate connection is finite element technique under monotonic loading at present. this paper applies nonlinear ( material, geometry and contact ) finite element method to analyze the behaviors of connections under cyclic load at fist time. contact elements are set between end plate and column flange, screw cap and neighborhood plane, bolt bar and hole

    對于端板連接的理論分析，目前國內外的研究主要局限在單向加載有限元分析范疇，本文首次採用三維非線性（包括材料、幾何與狀態非線性）有限元對端板連接進行了循環加載分析，端板與柱翼緣間、螺栓頭（帽）與相鄰板件間、螺栓桿與孔壁間都設置了反映邊界狀態的接觸單元。
  8. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。
  9. Then an thorough computer modeling using finite element program with material, geometry and state triple - nonlinear taken into account is carried out on a series of influencing factors, such as comparison with npn - beam splice connection, comparison of varies designed theories, and the varying of fraction coefficient, diameter, grade, pretension and arrangement of bolts, thickness of web and flanges of beam and column, splicing location, axial loading on column, etc. lots of useful conclusions are drawn form computer modelling. finally, design and construction suggestions are given out. this study fills the black in the field of steel beam - to - column connection with cantilever beam high - strength bolted - splicing at both home and abroad

    然後，本文在考慮材料、幾何和狀態三重非線性的基礎上，對該連接形式進行了全面的計算機模擬，主要考慮了帶懸臂梁段全螺栓拼接的樑柱連接節點與無拼接的樑柱連接及翼緣對接焊接腹板拼接的連接節點的對比，各種設計方法之間的對比，以及翼緣拼接和腹板拼接的螺栓間距、直徑和數量，拼接點與梁端之間的距離，梁和柱的翼緣、腹板厚度，柱的軸力，接觸面的摩擦系數，翼緣和腹板拼接板的厚度等因素的影響。
  10. With the extensive application of composite structures, the behavior of composite actionbetween concrete floor and steel beams has become an attractive area for research. consideringthis kind of combination function, the frame should be designed according to steel - concretecomposite frames, and the working behavior of its beam - column connections is the basis ofanalytic foundation of such frames

    隨著組合結構的廣泛應用，考慮鋼筋混凝土樓板和鋼梁之間的組合作用也正成為人們越來越關注的研究課題，考慮這種組合作用后，框架應該按鋼-混凝土組合框架進行分析設計，其樑柱連接節點半剛性工作性能的分析是這種組合鋼框架結構分析的基礎。
  11. After comparing between the finite - element analysis and experimental results, the author verified the fem. then according to the chinese code, the nonlinear finite model of the beam - to - column is established which are made of different size components. the responses of beam - to - column web moment connections which are made of different size components are compared and analyzed from three facets, and the conclusions about the joints behavior are drawn : thicken the connection plate, lengthen the connection plate or use a back - up stiffer can improve the connection behavior, consist of improving the behavior of load - supported and reducing the stress convergence in the flange moment plates

    本文根據我國規范的有關規定，自行建立了12個不同構件尺寸的樑柱腹板連接的三維有限元模型，對不同構件尺寸的樑柱腹板剛性連接節點在單向荷載作用下的反應進行了研究，從結構的mises應力等值線示意圖、梁端加載處的荷載? ?位移曲線、翼緣連接板兩端的mises等效應力以及翼緣連接板與柱相連接的三邊的mises應力等值線示意圖四方面進行了比較與分析，從而得出了不同構件尺寸的樑柱腹板剛性連接的在受力行為上的結論：增加翼緣連接板的厚度、增加翼緣連接板的長度以及採用柱的橫向加勁肋均可以改善節點的受力性能：提高節點的承載能力；減小翼緣連接板內部與柱翼緣邊的的應力不均勻現象，從而避免試件過早地發生破壞。
  12. A high degree of continuity can be achieved just providingthe slab with rebar running along the column. furthermore, stiffness and ultimate resistancecan be controlled in a rather simple way by a suitable selection of steel connection detailingand amount of reinforcement

    這種組合節點可以通過混凝土板內的縱向鋼筋實現組合梁在不同跨之間的連續性，而且通過選擇合適的型鋼樑柱連接方式和縱向鋼筋數量，可以有效地控制節點的剛度與承載能力。
  13. The study on the behavior of semi - rigid joints in steel - concrete composite frames gets widely attention recently. a high degree of continuity can be achieved at a very low cost just providing the slab with rebar running along the column. furthermore, stiffness and ultimate resistance can be controlled in a rather simple way by a suitable selection of steel connection detailing and amount of reinforcement

    鋼-混凝土組合框架中半剛性組合節點性能的研究近來引起了廣泛的關注，這種節點形式花很低的成本就可以通過混凝土板內的縱向鋼筋實現組合梁在不同跨之間的連續性，而且通過選擇合適的型鋼樑柱連接方式和縱向鋼筋數量，可以有效地控制節點的剛度與承載能力。
  14. The experimental research for beam - to - column connections of steel frame and the research influence on the steel frame is one subject of 2001 ' key research subject of ministry of construction of china, grant no. 01 - 2 - 085. researching for of beam - to - column connections under cyclic loading, for the factors effecting on the connections, for the deformation and failure character of connections, the arising order of plastic hinges and load - deformation hysteretic behavior of three pane frame under cyclic loading, the effect of semi - rigid connections on the frames, is the major purpose of this study

    本文進行的鋼框架樑柱連接的試驗研究和對框架的影響研究是建設部2001年科技攻關項目《新型空腔結構板輕鋼結構體系應用研究》的子課題，旨在研究樑柱連接在循環荷載作用下的滯回性能、影響連接的各種因素、連接變形特徵和破壞特徵；研究三榀平面鋼框架在循環荷載作用下構件塑性鉸出現的順序， p ?的滯回性能以及半剛性連接對框架側移以及塑性鉸出現順序的影響。
  15. There are still many problems remain to be solved in these aspects, such as behavior research on the lateral resistant of steel frame and connection etc. in this paper three 1 : 2 - scale steel frame specimens and eight full - scale steel frame connection specimens are tested on their behavior under cycle loading. there are six aspects as below on the problems of steel resident building researched : 1 pseudo - static force testing of eight full - scale connections, including top - seat angle connections, two web flange and top - seat connections and dog - bone connections are carried out for the first time in our country

    本文針對鋼結構住宅體系中亟待解決的若干問題，完成了三榀1 ： 2鋼框架模型和八個足尺比例的樑柱連接模型在低周往復荷載作用下的試驗，進行了以下幾個方面的深入研究： 1進行了頂底角鋼連接、帶雙腹板頂底角鋼連接等半剛性連接及狗骨式剛性連接這三種連接類型共八個原型試件的擬靜力試驗。
  16. But several earthquake has proved than it is of poor ductility and is brittle destroyed easily. but semi - rigid connections, which is formed by high strength bolts and connecting components, for example angle, end - plate and shape t steel, have an excellent energy dissipating mechanism to resist earthquake loads and prove more capacity for yielding and ductility

    而主要通過高強螺栓與連接件（角鋼、端板以及t型鋼等）把梁與柱連接起來的半剛性節點連接具有較強的耗能能力去抵抗一部分地震荷載，它能提供更多的屈服容量和延性容量，同時可節省節點的用鋼量，這使得半剛性連接成為一種既經濟又可靠的連接方式。
  17. Steel frame with welding joint easily occur brittle collapse because of having a low ductility at joints then ， a semi - rigid connected steel frame has large the energy absorption capacity which can resist dynamic loads and the using steel qualities of bracing system and joints are small so adopting a semi - rigid jointed steel frame is economical and stable but for semi - rigid connections are complex and variable ， in conventional analysis and design of steel structures ， it is usually assumed that the connections between columns and beams are either rigid or pinned the analysis of steel frames adopting the assumption can simplify the procedure of analysis and design ， but cannot precisely reflect structural practical circumstance and the errors of calculating results are large ， even ， get incorrect conclusions semi - rigid connection was referred to in chinese code for design of steel structures ( 2001 ， 10 ) ， however ， it isn ’ t specified how to apply semi - rigid joints in design in fact it cannot be carry out the purpose of the paper give a calculating method that accords practical engineering and easily put into effect worthwhile it is going to promote the development of semi - rigid jointed steel frame in design and heighten structural stability in the paper ， at first some commonly employed methods for the modeling of connection behavior are introduced richard abbott function modeling of connection is adopted for extended end plate bolted connection by the 34 test data comparing to regression analysis indicate richard - abbott function modeling of connection represents an excellent fit to test data then after a semi - rigid joint behavior can be modeled as a finite stiffness rotation spring ， base on rotation and displacement equation derive the element stiffness matrixes with semi - rigid connections where the effects ofj ointed flexibility geometric non - linearity and shear forces in the connection deformations have been considered in and fixed - end forces are modified finally, a program for calculating semi - rigid with incremental - iterative method has been

    本文的目的就是為半剛性連接鋼框架的設計提供一種既符合工程實際又簡便易行的計算方法，供規范使用過程的補充、延伸或參考；同時，也將促進半剛性連接鋼框架設計技術的發展，為提高結構安全性能、節省工程成本發揮應有的作用。本文首先介紹了常見的幾種應用較為廣泛的樑柱連接彎矩轉角關系模型，在分析比較的基礎上，選用richard ? abbott函數模型作為外伸端板連接彎矩轉角關系模型，通過對34個外伸端板連接的實驗數據與回歸分析得到的參數比較可知，經回歸分析得到的此模型參數與實驗數據符合較好。然後用彈簧表徵連接點的轉動剛度，根據梁的轉角位移方程推導出半剛性連接的剛度矩陣，在單元剛度矩陣中考慮了節點柔性、幾何非線性和剪切變形的影響，並對固端力進行了修正，最後用增量迭代法編制有限元程序進行計算和分析。
  18. According to the results of theory and experimental researches in this paper, the design provisions in the " technical code for concrete - filled square tubular structure " ( draft ) are discussed. the load - carrying capacity formulations for end section of beam to at the column - beam connections are proposed

    根據本文的試驗和理論研究結果，對（ （矩形鋼管混凝土結構技術規程》 （送審稿）帶內隔板的梁一柱栓焊連接節點設計內容進行了評析，提出了構造建議，並給出了樑柱連接處梁截面的抗彎、剪計算公式。
  19. To investigate the punching shear behavior of slab - column connections with nonrectangular columns, an experiment on the three specimens of column with three kinds of typical special - shaped cross - section ( cross - shaped section, t - shaped section and l - shaped section ), which were connected with reinforced concrete slabs, and reference specimens with square columns was conducted

    摘要為了研究柱截面形式為異形柱的板柱連接沖切受力性能，進行了柱截面形狀分別為3種典型異形柱（十字形、 t形和l形）和對比方柱所構成的板柱連接的沖切特性試驗。
  20. Based on the experimental result of the characteristics of reinforced concrete slabs with cross - shaped column and the yield - line theory, the yield - line pattern of reinforced concrete slab - column connection with cross - shaped column was presented and the flexural strength formula was derived

    根據所進行的柱截面為十字形異形柱板柱連接沖切特性的試驗成果，提出了十字形柱板柱連接的屈服線形式，並應用屈服線理論，導出了十字形異形柱板柱連接的抗彎承載力表達式。
分享友人
分享到 Line

分享到臉書