校準塊 的英文怎麼說
中文拼音 [jiàozhǔnkuāi]
校準塊
英文
calibration block-
Methods for calibration of vibration and shock pick - ups. resonance frequency testing of undamped accelerometers on a steel block
振動與沖擊傳感器的校準方法安裝在鋼塊上的無阻尼加速度計共振頻率測試As proved by experiments, the present method can effectively restrain the influence of speckle to the laser triangular measurement system and the obtained calibration accuracy is about 0. 05mm within 100mm depth range
只需對特殊設計的模塊進行一次測量，便可完成對整個測量系統的校準。該方法能夠有效的抑制激光散斑的影響，具有較高的系統精度。Rockwell hardness test - calibration of reference blocks
洛氏硬度試驗.基準塊的校準Standard test method for calibration and operation of the falex block - on - ring friction and wear testing machine
法列克司環塊磨擦試驗機和磨損試驗機的校準和操作標準試驗方法Vickers hardness test - calibration of the reference blocks
維氏硬度試驗.基準塊的校準Finally, the algorithm model of six modules ( space - calibration, time - calibration, spot - track ' unite, track ' s origination and expiration, the form of tracking - door and association algorithm ) are founded. the effect of some modules to tracking result are studied and their intimated results are gained. the intimation result of centralized - system and distributed - system are compared in the end
建立了空間校準、時間校準、點跡合併、航跡起始與終結、跟蹤門判斷和互聯演算法六個模塊的演算法模型；通過數字模擬，探討了某些模塊對跟蹤結果的影響並給出相應的模擬結果。Shore hardness test - calibration of reference blocks
肖氏硬度試驗.標準塊的校準Brinell hardness test - calibration of reference blocks
布氏硬度試驗.標準塊的校準It has standard weights to make the calibration and inspection conveniently the and quickly
機內裝有稱重標準塊，使精度校驗和檢測方便快捷。Iso 4545 - 3 - metallic materials - knoop hardness test - part 3 : calibration of reference blocks iso 4545 - 3 : 2005 ; german version en iso 4545 - 3 : 2005
金屬材料.硬度試驗.第3部分:標準塊的校準Metallic materials - instrumented indentation test for hardness and materials parameters - part 3 : calibration of reference blocks
金屬材料.測定硬度和材料參數用儀器壓痕試驗.第3部分:標準塊的校準This paper investigates the system, which is composed of multip1e laser stripe sensors, to profile foot and shoe moda1. at the same time, the paper proposes the technique of calibrating by single sensor and mul t iple sensors, regi strat ing and merging of 3 - - d range data, des igning the hardware and software
本文研究了採用多個激光線結構光傳感器的三維腳形測量系統，提出了系統校準模塊的設計，研究了多傳感器校準方法，多傳感器數據的配準和融合以及三維建模。7. based on our crsi and algorithm and double lcslm, an adaptive optical hardware system which c & n be used to model arbitrary complicated wavefront and the compensation of the wavefront can be accomplished was built. and according to the characteristic of a crs interferogram of a step wavefront produced by an lctv, the pixel - level calibration of this system is implemented
七、採用已建立的空間相位調制環路徑向剪切干涉儀及其波前重建演算法，和位相調制持性已知的兩塊液晶空間光調制器，創建了一套用於模擬產生任意畸變波前並加以檢測和反饋控制的自適應光學硬體系統，並通過臺階波前對該系統實現了像素級校準。Welds in steel. calibration block number 2 for ultrasonic examination of welds
鋼焊縫.焊縫的超聲波檢驗用第2號校準塊Non - destructive testing - ultrasonic examination - specification for calibration block no. 1
無損檢驗.超聲檢驗. 1號校準塊規規范Non - destructive testing - ultrasonic examination - specification for calibration block no. 1 ; german version en 12223 : 1999
無損檢驗.超聲波檢驗. 1號校準塊規范If using a calibrated template for marking and measuring in percent dimensional change directly, an initial measurement is not needed
如果使用一塊校準過的並可直接測量尺寸變化百分率的模板作標記，初始尺寸是沒必要的Non - destructive testing - ultrasonic testing - calibration block no. 2
無損檢測超聲檢測2號校準試塊Non - destructive testing - ultrasonic testing - calibration block no. 1
無損檢測超聲檢測1號校準試塊Welds in steel ; calibration block no. 2 for ultrasonic examination of welds iso 7963 : 1985 ; german version en 27963 : 1992
鋼材的焊接點.焊接點超聲波檢驗用的2號校準試樣塊分享友人