校準法 的英文怎麼說
中文拼音 [jiàozhǔnfǎ]
校準法
英文
calibrating method-
The influential factor of accuracy of measured pulp beating degree, including water temperature, pulp consistency, checking instrument and so on is discussed, and one convenient way of measuring pulp consistency is introduced
摘要初步探索影響測漿準確性的幾個因素,包括水溫、測漿濃度、儀器校準等,並介紹了一種簡單易行的濃度檢測方法。A remedy method of radial distortion of ccd camera
攝像機徑向畸變的校準方法Study on method of calibrating vacuum leak with constant conductance method
固定流導法校準真空漏孔方法研究Standard practice for calibrating a fathometer using a bar check method
用棒檢驗方法校準回聲測深儀的標準實施規范Acoustics - calibration method of hydrophone acceleration sensitivity
聲學水聽器加速度靈敏度校準方法The assembly language program collects and processes the data real time. comparing kinds of method of filter and arithmetic of fft, the author select the fir filter to realize pretreatment of signal and radix - 2 fft to distill the characters of librations
通過對各種濾波方法和fft演算法進行比較,本套數據檢測和校準處理系統採用fir濾波對採集到的信號進行預處理,利用基2fft演算法來提取信號的頻率特徵。Acoustics - low frequency calibration methods of hydrophones
聲學水聽器低頻校準方法Standard test method for calibration of microwave ovens
校準微波爐的測試方法Standard test method for trace impurities in monocyclic aromatic hydrocarbons by gas chromatography and external calibration
用氣相色譜法和外部校準法對單環芳香烴中微量雜質的標準試驗方法Calibration of vibration and shock pick - ups - methods for primary shock calibration by light cutting
振動和沖擊傳感器的校準.採用輕切削法對主沖擊的校準方法Methods for the calibration of vibration and shock transducers - primary shock calibration using laser interferometry
振動和沖擊傳感器的校準方法.採用激光干涉測量法的主要沖擊校準Based on the verification regulation of prt, this paper studies the temperature characteristics of prt, suggests a method of improving the accuracy of measurement and supplies the uncertainty of calibration point
摘要分析了檢定規程對鉑電阻溫度計的要求,通過研究鉑電阻溫度計的測溫特性,提出了提高鉑電阻溫度計測量精度的方法,並給出了在溫度校準點的測量不確定度。Lastly, the minimum permission reliability index is offered by the method of " calibration method " which makes back calculation out of the bending resistance reliability and the compression resistance reliability of the reinforced concrete member in norm
最後,根據「校準法」反演計算現行設計規范中鋼筋混凝土結構抗彎、抗壓可靠度指標以確定在用橋梁結構體系的最低目標可靠度指標。The method using square wave excitation presented by the paper is verified by theories and experiments that the method meets the requirement of accuracy, and this method ' s application simplifies manipulations and improve greatly the calibration efficiency
其中本文提出的方波信號激勵的比較校準法,理論和實驗證明不僅滿足校準精度要求,而且簡化操作,大大提高了校準的效率。Secondly, precipitation from the radar estimating precipitation model ( rep ) are verified using a rain - gage network of 127 stations in order to show the effects of five methods : zi, optimal interpolation joint of optimal interpolation and kalman filter, kalman filter, and average method. the results show that the method of optimal interpolation and the method of joint have the lowest rms errors and the method of zi has the highest rms errors
結果表明:將地面雨量計值作為真值,則聯合校準法和最優插值校準法得出的降水量計算精度最高,卡爾曼濾波校準法和平均校準法的計算精度低於聯合校準法和最優插值校準法, zi關系法的精度最低。Free calibration by self - calibrate in gas sensor system
用雙路自校準法實現氣敏傳感器的長期穩定工作In - flight camera calibration method
攝影機空中校準法Plastics - determination of average molecular mass and molecular mass distribution of polymers using size - exclusion chromatography - universal calibration method
塑料.用粒度排除色譜法測定聚合物的平均分子量和分子量的分佈.通用校準法The multi - port measurement system has the widespread use in microwave measurement, the measurement of multi - port device with two - port vector network analyzer ( vna ) is researched. this paper analyzes the commonly used error models and calibration methods of vna, program a trl calibration procedure for two - port vna, and compare the tested data with the data from vna. the comparison show that the programmed trl calibration procedure is in the same accuracy as the vna
本文討論了兩埠矢量網路分析儀常用的誤差模型和校準方法,編制了兩埠矢量網路分析儀基於trl校準法的校準程序,並把校準后的測量結果和矢量網路分析儀校準后的測量數據做了比較,比較結果說明編制的trl校準程序校準效果和矢量網路分析儀校準的效果相同。Last, the reliability of 50kg / m - rail and 60kg / m - rail is calculated by using the method combing the mote - carlo imitation with the finite element method. on the basis of the calibration method, the objective reliability index of the steel rail is recommended, and the problems of the present standards of the rail - wear limits are pointed out, and then the rail - wear limits are discussed
最後,採用有限單元法與蒙特卡羅法相結合的方法對50kg m軌和60kg m軌的可靠度進行了計算,根據「校準法」的思想得到了鋼軌目標可靠指標的建議值,指出了現行鋼軌磨耗標準所存在的問題。分享友人