核孔環 的英文怎麼說
中文拼音 [hékǒnghuán]
核孔環
英文
annulus of nuclear pore-
The ultrastructure of the merozoites of eimeria tenellawas observed and discribed. the pellicle consist of two layer membranes, the outer membrane was a continous covering enclosing the whole merozoites, while the inner pellicular complex is interrupted at the anterior and the micropore, and thicken to form the polar ring and micropore. there are 24 microtubules under the pellicle of the merozoite which originated from the polar ring, all of them are connected with the polar ring, and extend alongside the inner pellicular complex to the middle of the merozoite. the head of the merozoite consists of a conoid, an apical vesicule and polar ring. the conoid is a hollow truncated cone. the conoid and spical vesicule can stretch and contract. there are three or more rhoptry and a lot of micronemes. the nucleus has nucleolus. and two layer membranes
利用透射電鏡對柔嫩艾美耳球蟲裂殖子的超微結構進行了觀察描述.柔嫩艾美耳球蟲裂殖子的表膜由外膜和內膜復合體兩層組成，外膜連續，內膜復合體在頭部斷開形成極環，在其它部位斷開形成微孔；裂殖子的膜下微管24根，起始於極環，向後延伸至細胞核處；裂殖子的頭部由頂泡、錐體和極環組成，錐體和頂泡可以伸縮；柔嫩艾美耳球蟲裂殖子棒狀體3個以上，微線數量很多，二者都由電子緻密的結構組成；細胞核位於裂殖子的中後部，外被雙層膜，有電子緻密的核仁和染色質The key components in laser gyro is he - ne ring laser, and the reciprocal action theory between light and medium is the base in studying the ring laser, use the lamb half classical theory, and on the base of density matrix theory, the optical brounch equation was established, which described the movement of amplifying medium atom in the ring syntonic cavity, and according to the medium polarize theory the self consistent equations was deduced, which describe the light intensity and phasic of the counter - propagating wave. on the basis of this equations, adopted the simulation software matlab and virtual instrument programming language labwindows / cvi, we can do some simulated experiments in study the phenomenas such as amplify and dispersive characteristic of medium, mode pushing effection, burned hole effection and pattern competition, lock - in of frequency and the characteristic of light intensity and phasic of the counter - propagating wave in laser gyro
激光陀螺的核心部件為he - ne環形激光器，而掌握光與介質的相互作用理論是研究激光器的關鍵，採用拉姆半經典理論為主，在密度矩陣理論的基礎上，推導環形諧振腔中描述he - ne氣體增益介質原子運動的光學布洛赫方程，運用介質極化理論得出描述激光陀螺反向行波的光強、位相所滿足的自洽場方程組，在此基礎上，運用matlab模擬軟體和虛擬儀器編程語言labwindows / cvi ，對激光陀螺中的介質增益色散特性、頻率牽引效應、燒孔效應及模競爭、閉鎖效應及環激光的光強和相位特性進行模擬試驗研究，並且運用全量子理論，對激光工作原理進行分析，得出二能級系統單模輻射場的光子數密度分佈，得出激光場的光子統計分佈，模擬激光場的動態建立過程。In this paper, firstly the macro parameter of the series connection app was comprehensively analyzed, among which the trajectory location of the bullet emission and the terminal velocity of the bullet were mainly analyzed, and the feasibility of the series connection app to cope with explosive reactive armor was demonstrated. and then the macro design about the head of the series connection app was made, among which a particular analyse about the bullet " s launching process was made, from which we concluded the relation between the thickness of the airproof loop and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the burning rate of the powder and the relation between the length of the bullet and the maximum pressure of the emission hole and the relation between the length of the bullet and the emitting time of the bullet, and the reasonable str ucture of the head of the carrier and bullet were designed, then the intensity of the head of the carrier was checked out using of the software of ansys
本文首先對子母式穿甲彈總體參量作了全面的計算分析，其中主要分析了子彈射出的彈道位置和必要的子彈著靶速度，論證了子母式穿甲彈對付爆炸式反應裝甲的可行性，然後對子母式穿甲彈彈頭部進行了總體設計，其中主要對子彈的發射過程進行了詳細的分析，得出了母彈彈頭部發射孔內閉鎖環厚度與子彈飛離母彈速度的關系、子彈長度與子彈飛離母彈速度的關系、子彈長度與火藥燃燒率的關系、子彈長度與母彈彈頭部發射孔內最大壓力的關系以及子彈的長度與子彈發射所需時間的關系，設計出了合理的母彈彈頭部結構和子彈的結構，並利用ansys有限元分析軟體對母彈彈頭部的強度進行了校核。The results of calculation show that these algorithms are succinct, efficient, accurate, reliable, and they can accomplish the optimal design of integrated layout and connection scheme with high intelligence
重點是應用ngsa演算法進行布局即裝配關系設計的實現技術。裝配關系設計以前五個環節為底層支撐，構成液壓集成塊布局布孔優化設計方法的核心內容。As the key component of ihs, hydraulic manifold block ( hmb ) is still difficult to be designed in nowadays factories. one reason for that is the complexity of this problem, which mainly consists of outer layout and inner connection problems
一方面原因在於該問題的復雜性，其設計內容包括外部布局和內部布孔的集成方案制定；另一方面原因是目前的cad技術未能有效地應用到集成塊設計的核心環節中，還沒有真正減輕設計者智力勞動強度和非智力勞動量。分享友人