梁板構造 的英文怎麼說

中文拼音 [liángbǎngòuzào]
梁板構造 英文
beam and slab construction
  • 梁 : 名詞1 （屋架中架在柱子上的長木） beam 2 （通常也指檁） purlin 3 （橋） bridge4 （物體中間條狀隆起...
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 造 : Ⅰ動詞1 （做; 製作） make; build; create; produce 2 （假編） cook up; fabricate; concoct 3 [書面語...
  • 構造 : structure; construction; constructional detail; tectonic; structural; makeup; anatomy; constituti...
  1. The two specimens, which are designed as : main beam - pre - stress beam ? floor ? frame columniation assemble the space specimens. in order to checkout whether the code can be applied for the special structure systems, the structure of the specimens refer to the current gb50010 - 2002 concrete structure design code and gb50011 - 2001 seismic resistant code

    本文試件的各組成構件為：非預應力邊梁預應力梁板框架柱組合空間試件，各組成構件的構造參照了現行《 gb50010 - 2002混凝土結構設計規范》及《 gb50011 - 2001抗震規范》的有關規定，以檢驗規范及設計條例能否適用於該特殊結構形式。
  2. The main components of the latter are multi - rib sandwich panels, including floor slabs and wall slabs. reinforced concrete conformation columns are set where the longitudinal walls and latitudinal walls intersect and copulative beams are set where floor slabs and wall slabs intersect. they play a role of linking and transferring loads, bearing a small part of loads at the same time

    無骨架體系的主要承重構件是密肋夾芯板（包括樓板和墻板） ，縱、橫墻相交處設鋼筋混凝土構造（連接）柱，墻板和樓板相交處設連系（圈）梁，連系梁和柱主要起連接和傳遞荷載作用，也承擔少部分荷載。
  3. Considering the special structure of multi - ribbed slab, founding diphase body mechanical model of compound material, strengthening rib beam and rib pillar by equivalent volume ratio of concrete and slice brick, the paper drew elastic compution constant and shear constant. based on the things, the paper simplified isotropy compution model to wall, gave practical design formula of elastic mold and shear mold, provided necessary parameter for practical design formula of elastic rigidity. finally the calculating results agree well with the text results

    結合密肋復合墻板的特殊構造，建立墻板的復合材料二相體力學模型，按照混凝土與砌塊體積比不變原則對肋梁肋柱同時加強，得出墻板的彈性計算常數及剪切常數，在此基礎上，進一步將墻板簡化為各向同性的計算模型，給出墻板彈性模量及剪切模量實用計算公式，為密肋復合墻板的實用彈性剛度計算公式提供必要的參數。
  4. Based on the numerical simulation and accuracy analysis to previous slab ' s test with the ansys program, the study of composite wall, with various detail design under potential load action respectively or jointly is carried on and the wall ' s atress behavior and failure mode is obtained, also the influence to wall ' s stiffness and bearing capacity by kinds of factors, including wall ' s shear span ratio, member ' s section, bar arrangement, etc. based on the hammer blow test and stiffness test, a 1 / 3 scale ten - bay model ' s modality parameter and elastic deformation characteristic is analyzed

    在對密肋復合墻板運用ansys ~ （ （ ? ） ）程序進行數值模擬、分析驗證的基礎上，對典型組合墻體在不同連接構造和不同荷載效應組合作用下的受力形態和破壞模式進行研究；計算分析了復合墻體剪跨比、邊框柱截面尺寸、邊框柱配筋大小以及墻板內肋梁肋柱配筋等諸多因素對密肋復合墻體承載力及剛度的影響，得出其變化規律。
  5. This thesis investigated and researched on non - loaded crack, especially those caused by thermal - shrink, and analyzed the thermal - shrink stress of beam, slab and continuous - wall, found that according data of civil and overseas offered thermal - shrink calculating formula without considering effect of factors, such as the cement quantity, using of aruhuesiru, aggregate size and quantity of sand, which made the result data smaller. in addition, there are not enough construct measure in code

    本文對非荷載裂縫，特別是溫度?收縮裂縫進行了調查研究，並對兩端或四周約束的梁、板和底部約束的地下連續墻進行了收縮應力分析，發現國內外有關文獻給出的收縮計算公式沒有考慮泵送商品混凝土的水泥用量、外加劑使用、骨料粒徑和砂用量等因素的影響，計算出的混凝土收縮量往往偏小；另外， 《規范》中針對溫度?收縮裂縫的構造措施不足。
  6. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。
  7. Secondly, this paper made some theoretic researches on its engineering classfication and applicable scope for this technology ; then combining with project example, this paper carried out scheme design for this technology, and compared some different kinds of underpinning scheme and node and structure design, and put forward the method of " reinforcce steel bar through column " to build pile cap beam, " resistant bend and shear anchored reinforce steel bar " to strengthen column consolidation effect, and the method of " steel plate hoop " to build reinforcing bar connection of the foundation beam, etc. in the process of the consturction scheme research and implement, this paper synthetically elaborated the organizaton for project construction, put forward the construction technical measure of specific aim on the artificial pile, and pile cap beam, and underground adding layer and structure stabilization, and overall structure stabilization and so on. for this project, adopt reinforcing bar concrete to brace hole wall to ensure the safety of engineering in the artificial pile construction, use flexible connection catch to make the cage hoisting easier to simplify the construction process, use the method of earthwork statified symmetrical balance in the process of underground adding layer excavation

    本文首先對于基礎托換與結構加固技術的目的和意義、國內外發展狀況進行了綜合闡述；其次對該項技術工程分類及適應范圍進行了理論上的分析研究；然後結合工程實例對該項技術進行了方案設計，對比幾種不同的托換方案和節點及構造設計，提出了「通筋穿柱法」做承臺梁， 「抗彎抗剪錨筋法」強化柱加固效果， 「鋼板箍法」做地基梁鋼筋連接點等多項技術；在施工方案的研究和實施過程中，對于工程施工組織進行綜合闡述，並就人工挖孔樁、承臺梁、地下加層及結構加固、整體結構穩定等專項施工方案提出有針對性的施工技術措施，人工挖孔樁施工採用鋼筋砼護壁確保挖孔樁的安全成型，使用柔性連接鉤進行鋼筋籠吊裝簡化施工工序；承臺梁施工採用梁主筋橫穿柱身化學膠錨固等；地下加層綜合施工技術採用土方分層對稱平衡開挖，分段挖土做筏基結構自穩等；最後對于該工程實施后的效果分析，說明該項綜合施工技術的可行性。
  8. Based on analyzing the exploitation and applying of bridge bearing, aiming at the hotspot of bearing research, the paper introduces the isolation bearings " structure and working mechanism. the paper also brings forward a promising isolation bearing model - polysaccharid sliding rubber bearing + high damping rubber damper

    本論文在分析國內外橋梁支座開發應用現狀的基礎上，針對目前橋梁支座開發研究的熱點，對現有減震支座的構造和工作機理做了簡單的介紹。認為聚四氟乙烯滑板支座+高阻尼橡膠阻尼塊分離式減震支座是一種很有發展前景的減震支座形式。
  9. The local geometric details considered include longitudinal length and height of access hole in beam web ; material nonlinearity and geometric nonlinearity are included in nonlinear analyses

    節點局部構造的變化主要考慮梁腹板上的焊接孔的長度和高度的改變，非線性分析包括了對材料非線性和幾何非線性的考慮。
  10. The contents include : based on the previous research and the data of experimentations, the author researches and develops a kind of satisfactory semi - empirical formula of nonlinear temperature distribution, and calculates the temperature stress of rigid - framed arch bridge by the fem. the temperature effects of bridge structure by annual and sunlight temperature difference are discussed, it indicates that the temperature effect of annual temperature difference is small but the temperature effect of sunlight temperature difference is great and the temperature stress along beam depth resulted from sunlight temperature difference is nonlinear. with the comparison between the temperature effects of different position of bridge, the results show that where the section of bridge is small, the temperature stress of it is large

    本文主要包括以下內容：從理論上研究並結合實測資料發展了一種比較理想的半經驗溫度場非線性分佈公式，並將有限元方法應用於剛架拱橋結構溫度應力的計算中，對橋梁結構進行整體溫度應力分析；討論了年溫差和日照溫差引起的橋梁結構的溫度效應，表明年溫差引起的溫度效應較小，而日照溫差引起的溫度應力較大且沿梁高呈非線性分佈；分析比較了橋梁結構各個部位的溫度效應的大小，可知截面越小溫度拉應力越大，受力越不利；並對箱梁結構由於構造不同引起的縱向與橫向的溫度效應大小進行了探討，發現在頂板下緣也會出現相當大的溫度拉應力，並且梗腋的存在反而增加了頂板底部的溫度拉應力；還對幾種相近的剛構式橋型的溫度效應進行了分析對比，總結了這些橋型針對溫度效應的優劣，並提出相應的針對性措施。
  11. Firstly, for the system of moulding board and support frame in construction the side pressure and screws are analyzed. the material and structure form of support frame are discussed. the design of support frame uses the method of limited state, and also it analyses the integer stability, part stability, and single stability, and then proposes the load analysis of multi - level support frame

    首先，針對轉換層梁模體系及支撐架施工，重點分析了轉換層結構現澆混凝土對模板側壓力值及模板對拉螺桿的計算；討論了轉換層支撐體系的形式及構造，詳細論述了基於極限狀態設計的支撐架計算方法，包括縱橫向水平桿的強度驗算、立桿的整體穩定性、局部穩定性、單肢桿件穩定性等驗算，並提出了多層支撐架的施工荷載計算方法。
  12. The company is capable to design and manufacture all alone all kinds of containers and flow office con | ainers, and as request make structurally special enntainers and flow office containers, such products with large capacity and extra height and lcngth as steel containers, ventilators, open top containers, open side containers, eqnipment containers for special purpose, office maintenance containers, living containers, rush bin, toilet case, watch house - ease, containers for dining hall, 2 in 1 or 3 in l office compound meeting room, collapsible containers, and other containers and flow office containcrs of distinct sizes

    佛山市南海平洲友利集裝箱有限公司能自行設計製造各類集裝箱及流動辦公室箱，也能按客戶要求製造特殊構造的集裝箱及辦公箱，如大容積超高超長的鋼質集裝箱、通風箱、開頂箱，側開門箱、設備專用箱、辦公裝修箱、住宿箱、垃圾箱、廁所箱、值班室箱、飯堂用箱、二合一或三合一組合辦公會議室箱、裝拆箱及其他不同尺寸的貨箱及辦公箱和集裝箱專用部件、八字板、頂板、側板、低橫梁、角柱頭等。
  13. In this thesis, the new structure of pre - stressed cantilever composite beam with corrugated steel webs on steel - concrete composite spine girder was brought forward for the first time, a series of experimental researches and theoretical analyses relating to this new structure are conducted, including load transverse distribution rule, shrinkage and creep effect, temperature difference effect, and ultimate bearing capacity

    本文提出大懸臂預應力波形鋼腹板挑梁這一新的構造形式，對其橫向分佈規律、收縮徐變、溫差效應以及承載能力等方面的受力特徵進行了分析和試驗研究。
  14. The main work is described as follows : ( 1 ) this thesis introduces the phylogeny, research and application actuality inland and abroad of steel - concrete composite structure with corrugated steel webs, summarizes the basic construction and forcing characteristic of pre - stressed cantilever composite beam with corrugated steel webs

    主要做了以下工作: （ 1 ）介紹了波形鋼腹板組合結構的發展歷史、在國內外的研究應用現狀，總結了預應力波形鋼腹板組合挑梁的基本構造特點和受力特徵。
  15. Though great progress has been achieved on researches on the design theory, structural type, structure details and construction method of the composite bridge, there are still many problems, such as crack control of the concrete deck, influence of the connecting rigidity over the structural mechanical characteristics and mutual depende ncy between design and construction, need deeper researches for better solutions

    對組合結構橋梁的設計理論、結構形式和構造細節、施工方法等方面的研究已經取得了很大進展，但仍然存在許多問題需要深入研究和完善，例如：混凝土板裂紋控制、接合剛度對結構受力性能的影響、設計與施工的依存性等。
  16. A material nonlinear finite element analysis for the cast - in - place reinforced concrete hollow slab that occurs from initial loading, cracking, yielding to failing is carried on. the cracking load, ultimate load, the displacement rules and the principal stress distribution rules of the hollow slab under the vertical loads are obtained. a material nonlinear finite element analysis for the single span hollow flat - plate floor is also carried on

    其次對空心板進行了從加荷、開裂、屈服直至破壞的全過程材料非線性有限元計算，得到了空心板在豎向荷載作用下的開裂荷載、極限荷載及位移和應力分佈規律；還對單跨無梁樓蓋進行了材料非線性有限元計算，通過分析主應力場明確了柱上暗扁梁的作用；有限元計算的結果驗證了以上的理論分析並得到了一些重要的結論，對改進現澆空心板無梁樓蓋的構造措施有重要的參考價值。
  17. This paper mainly describes the constructions of the formwork which is used in the monorail transit system in chongqing, and indicates that during the track girders ' fabrication, it is very important to pay attention to steel fabrication, orientation of conduct for tendon passing, the mixing, molding and maintaining of the concrete and the stretching of the prestressed tendon

    介紹了重慶市單軌交通系統中的預應力混凝土軌道梁模板的構造，並闡述了在軌道梁製作過程中應重點做好鋼筋製作、預應力管道定位、混凝土拌制、成型、養護及預應力筋張拉等工序的工作。
  18. Directed against the characteristic of variational high box - girder structural force, and numerical analysis of to be built bridge, taking into account construction stabilization and intension, the thesis putts forward optimal formula constructional range of isotropic box - girder thick, girder highness and underside bridge curve

    針對變高度箱梁的結構受力特點，結合實橋資料的數值分析，考慮結構穩定及強度的影響，給出了各向同性箱梁板厚、箱梁梁高和梁底曲線的優化設計公式及構造范圍。
  19. During the finite element modeling of the bridge, the factors affecting the accuracy of the finite element model are discussed in detail, such as, the geometrical non - linearity of the cable including gravitational sag and initial tension, and the structural orthotropic steel box - girder deck to be equivalent to physical orthotropic deck by using compound material mechanics, and so on

    在建模過程中，盡可能多地考慮了一些影響全橋有限元模型精度的因素：如斜拉索的幾何非線性（重力垂度和初始應力） ，將構造正交各向異性鋼箱梁橋面板用復合材料力學的方法等效為物理正交各向異性板等。
  20. The interpolating wavelet bases are constructed in order to deal with boundary conditions conveniently at first. then the wavelet bases of duality in product form are used to construct the generalized field functions of beam, plate and shell. the model of multivariable wavelet fem is built by hellingger - reissner and hu - washizu generalized variational principle

    首先構造了便於邊界條件處理的插值小波基，應用乘積型二元插值小波基來構造梁、板、殼的廣義變量場函數，通過二類、三類變量廣義變分原理建立了多變量小波有限元模型。
分享友人
分享到 Line

分享到臉書