梁節點 的英文怎麼說

中文拼音 [liángjiédiǎn]
梁節點 英文
girder connection
  • 梁 : 名詞1 （屋架中架在柱子上的長木） beam 2 （通常也指檁） purlin 3 （橋） bridge4 （物體中間條狀隆起...
  • 節 : 節構詞成分。
  • 點 : Ⅰ名詞1 （液體的小滴） drop （of liquid） 2 （細小的痕跡） spot; dot; speck 3 （漢字的筆畫「、」）...
  • 節點 : [電學] panel point; hybrid; packing; node; nodal points; joint of framework; pitch point; point pitch
  1. From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints

    採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。
  2. The horizontal shear strength of the exterior reinforced concrete beam - column joints is analyzed by the stress of the conterminal beam and column

    摘要針對鋼筋混凝土框架結構，根據與框架外節點相連的梁、柱構件的受力狀態，分析了外節點核心區所受水平剪力。
  3. Cross beam gusset plate

    橫梁節點板
  4. Element stiffness matrix and nodal load matrix of circular beam

    曲梁的單元剛度矩陣和節點荷載列陣
  5. Sliding displacement of beam longitudinal bars in staggered joints is smaller than in ordinary joints, and the beam bar " overstrength in staggered joints is more serious than in ordinary joints when shear force is equal in the two types of joints

    2在節點所受剪力相同的情況下，錯層節點中梁縱筋的粘結滑移比普通節點的要小，梁筋的超強更嚴重。
  6. Three - dimensional photoelastic test of beam - arch joint of open spandrel rigid - frame arch bridge

    空腹式剛架拱橋梁拱節點三維光彈性試驗研究
  7. Spatial static behaviors analysis on beam - arch joint of new - type rigid - framed arch bridge with open spandrel

    空腹式新型鋼架拱橋梁拱節點空間受力分析
  8. The shear mechanism, failure mode, deformation capacity, bearing capacity and the reliability of the anchored angle steels of the wrapped steel concrete cast - in - site frame typical story exterior joints under the middle and high axial compression ratio ( n = 0. 3, 0. 5, 0. 6 ), the working performance, failure mode, and the shear capacity of top story joints under the crack moment, the hysteresis characteristic and the dissipation energy capacity of the test joints are all analysed based on the 1 / 4 model pseudo - static tests of five specimens of wrapped steel concrete cast - in - site frame exterior joints, which varied in axial compression ratio, distribution of the beam angle steels and the stirrup ratio

    基於上述分析，本次試驗通過五個外包鋼混凝土邊節點1 4比例模型的偽靜力試驗，以柱的軸壓比、梁角鋼布置形式、配箍率等為主要參數，分析外包鋼混凝土現澆框架一般層邊節點在中高軸壓比（ n = 0 . 3 、 0 . 5 、 0 . 6 ）條件下，節點的抗剪機理、破壞模式、變形能力、承載能力和角鋼錨固的可靠性；分析了頂層邊節點在張開彎矩作用下的工作性能、破壞模式和抗剪承載力；分析了試驗節點的滯回性能和耗能能力。
  9. The work done in this paper is mainly as follows : ( 1 ) the wide beam should intrude to the wall at some length to make the flexural stress uniform along beam section width, thus make full use of the beam ' s bearing capacity and avoid the shear failure in the concrete joint. and it also prevents stress focus and concrete crack in the local shear wall

    關于寬梁與薄墻肢節點，可以得出以下幾點初步結論：寬梁應該深入墻肢一定的深度，以使寬梁截面的彎曲應力沿著梁截面寬度分佈均勻，充分發揮寬梁的抗彎能力，同時避免節點區混凝土的剪切失效，也避免剪力墻的局部因為受到的應力過大而拉裂。
  10. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。
  11. ( 2 ) from the equilibrium conditions of the isolated segment from a beam - column sub - assemblage, it is clarified for the first time that the bond stress along the beam rebars passing through the joint transfers into the column end to balance shear at this column end at the same ratio as that of the compression force in the compressed concrete at beam ends

    通過對樑柱組合體柱脫離體的平衡條件，首次明確了貫穿節點梁筋粘結應力和梁端受壓混凝土的壓力以相同的比例傳入柱端以平衡柱端剪力，從而對節點區的傳力機理重慶大學博士學位論文結出了完整的和具有說服力的解釋。
  12. Secondly, this paper made some theoretic researches on its engineering classfication and applicable scope for this technology ; then combining with project example, this paper carried out scheme design for this technology, and compared some different kinds of underpinning scheme and node and structure design, and put forward the method of " reinforcce steel bar through column " to build pile cap beam, " resistant bend and shear anchored reinforce steel bar " to strengthen column consolidation effect, and the method of " steel plate hoop " to build reinforcing bar connection of the foundation beam, etc. in the process of the consturction scheme research and implement, this paper synthetically elaborated the organizaton for project construction, put forward the construction technical measure of specific aim on the artificial pile, and pile cap beam, and underground adding layer and structure stabilization, and overall structure stabilization and so on. for this project, adopt reinforcing bar concrete to brace hole wall to ensure the safety of engineering in the artificial pile construction, use flexible connection catch to make the cage hoisting easier to simplify the construction process, use the method of earthwork statified symmetrical balance in the process of underground adding layer excavation

    本文首先對于基礎托換與結構加固技術的目的和意義、國內外發展狀況進行了綜合闡述；其次對該項技術工程分類及適應范圍進行了理論上的分析研究；然後結合工程實例對該項技術進行了方案設計，對比幾種不同的托換方案和節點及構造設計，提出了「通筋穿柱法」做承臺梁， 「抗彎抗剪錨筋法」強化柱加固效果， 「鋼板箍法」做地基梁鋼筋連接點等多項技術；在施工方案的研究和實施過程中，對于工程施工組織進行綜合闡述，並就人工挖孔樁、承臺梁、地下加層及結構加固、整體結構穩定等專項施工方案提出有針對性的施工技術措施，人工挖孔樁施工採用鋼筋砼護壁確保挖孔樁的安全成型，使用柔性連接鉤進行鋼筋籠吊裝簡化施工工序；承臺梁施工採用梁主筋橫穿柱身化學膠錨固等；地下加層綜合施工技術採用土方分層對稱平衡開挖，分段挖土做筏基結構自穩等；最後對于該工程實施后的效果分析，說明該項綜合施工技術的可行性。
  13. The vertical stiffener connection is suitable for rectangular steel tube column that the sectional area is smaller and h - steel beam connections

    摘要垂直加勁肋節點適于柱截面較小的方鋼管（矩形管）柱和h型鋼梁節點。
  14. Shear strength at primary and secondary beam nodes of preformed holes of composite frame structure

    迭合框架結構預留洞口主次梁節點的抗剪性能
  15. Many optimization joints mid design methods which have been applied in actual engineerings are put forward, including the rc looped - beam joint, enforced - steel loop joint, joint between columns filled with steel tubes and rc beams, joint between columns filled with steel reinforced concrete and rc columns, joint between column filled with steel tube and composite beam, composite beam design method, prestressed laminated open - web truss mid so on

    其中，提出的較優化的鋼筋砼環梁節點、鋼加強環節點、鋼管砼柱與鋼筋砼柱節點、鋼骨砼柱與鋼筋砼梁節點、鋼骨磚柱與組合梁節點及組合梁設計方法、預應力疊層空腹桁架等，都已應用於實際高層建築中。
  16. At present time, however, critical factors for which extensive applications of cfrt structure will be influenced is joint detail scheme. thus investigation on joints between cfrt columns and steel beams in medium - high rise residential construction has significant theoretical and applied value, so has research on reasonable and effective joint detail scheme

    然而，目前制約方鋼管混凝土結構推廣應用的主要問題在於節點構造方案，因此，開展針對中高層住宅建築的方鋼管混凝土柱?鋼梁節點研究，探討合理、有效的節點構造方案，具有十分重要的理論意義和應用價值。
  17. An equation to calculate ultimate shear - resistant capacity of src column and steel beam joint is discussed, with consideration of the actions of concrete, steel web and horizontal hoop. the effects of axial press and steel wing under loads are also discussed

    探討考慮混凝土、型鋼腹板、箍筋共同貢獻的勁性柱?鋼梁節點極限抗剪承載力計算公式，並就軸壓力、翼緣在節點受力過程中的作用進行了分析與評價。
  18. In the pseudo static tests of the middle joint and border joint, the failure modes, the carrying capacity, the ductility, the hysteresis loops and the stress transfer mechanism of the src column and steel beam joints under seismic loads are researched, which are compared with rc beam - column joints and src beam - column joints

    通過中柱節點和邊柱節點的擬靜力試驗，著重分析了勁性柱?鋼梁節點在模擬地震作用下的破壞形態、承載力、延性、滯回特性與應力傳遞機制，並與鋼筋混凝土節點、勁性混凝土節點進行了比較。
  19. Based on experimental research and theoretical analysis, investigations on the new type of joint are made systematically, the main contents and results include the following items. 1 four specimens of new joints between cfrt columns and steel beams are designed. by low - cyclic reversed load test, skeleton curves of new joints and shearing deformation in joint core area are studied, the influence of parameters, such as concrete cores, length of stiffener, and relative dimensions of column and beam, is discussed

    本文在分析現有節點方案特點的基礎上，提出了角鋼加勁式節點方案，並採用試驗和理論分析相結合的方法，對這種新型節點進行了系統研究，主要研究內容與成果如下： （一）設計了4個新型方鋼管混凝土柱?鋼梁節點的試件，通過對新型節點的低周反復荷載試驗，研究了新型節點的骨架曲線和節點核心區剪切變形等，探討了內填混凝土、加勁肋長度和樑柱相對尺寸等對節點抗震性能影響。
  20. This paper puts up a new method for installing steel beam joints on concrete structures by chemically - planted steel bars

    摘要提出了在混凝土結構上化學植筋，再通過塞焊和灌漿安裝鋼梁節點板的新方法。
分享友人
分享到 Line

分享到臉書