條件屈服強度 的英文怎麼說
中文拼音 [tiáojiànqūbìqiángdù]
條件屈服強度
英文
offset yield strength- 條 : Ⅰ名詞1 (細長的樹枝) twig 2 (條子) slip; strip 3 (分項目的) item; article 4 (層次; 秩序; 條...
- 件 : Ⅰ量詞(用於個體事物) piece; article; item Ⅱ名詞1. (指可以一一計算的事物) 2. (文件) letter; correspondence; paper; document
- 服 : 服量詞(用於中藥; 劑) dose
- 強 : 強形容詞(強硬不屈;固執) stubborn; unyielding
- 度 : 度動詞[書面語] (推測; 估計) surmise; estimate
- 條件 : 1. (客觀的因素) condition; term; factor 2. (提出的要求) requirement; prerequisite; qualification
-
Hot - rolled flat products made of high yield strength steels for cold forming. part 1 : general delivery conditions
冷成型用高屈服強度鋼熱軋扁平軋材.第1部分:一般交貨條件Cold - rolled flat products made of high yield strength micro - alloyed steels for cold forming. general delivery conditions
冷成形用高屈服強度微合金化鋼冷軋扁平材.通用交貨條件Specification for hot - rolled flat products made of high yield strength steels for cold forming - general delivery conditions
冷成型用高屈服強度鋼制熱軋扁平產品.第1部分:一般交貨條件Hot - rolled flat products made of high yield strength steels for cold forming. part 2 : delivery conditions for thermomechanically rolled steels
冷成型用高屈服強度鋼熱軋扁平軋材.第2部分:熱機械軋制鋼的交貨條件Developing a software for the testing machine measuring and controlling system. the software can automatically switch control mode according to standard in the process of tensile testing and automatically judge constitutive mode of material. at the same time, it can automatically measure elastic modulus e, yield strength o s, proof strength, non - proportional extention o 0. 2, percentage extention 8, tensile strength o b, etc. it can applied in industry practice
在經典pid控制與模糊控制的基礎上,設計了模糊自適應pid控制應用於試驗機的應力、應變及位移控制; 3 、開發了一套完整的試驗機測控系統軟體,能在試樣拉伸過程中按標準自動切換控制方式並自動判別材料本構模式,能夠自動測定彈性模量e 、屈服限_ s 、條件屈服限_ ( 0 . 2 ) 、延伸率、強度限_ b等,應用於工程實際。Interestingly, it was found that the er properties of this ternary composite depended on the content of formide. when the weight ration between mmt and formide was closed to 1 : 0. 08, the yield stress of er fluid could reach its maxium and the typical yield stress was over 8. 3 kpa at only 2 kv / mm electric field, which was 3. 2 times than that of mmt / cms er fluid. when the electric field was 3 kv / mm, the yield stress was over 12. 0 kpa, which was 2. 4 times than that of mmt / cms er fluid
當蒙脫土/甲酞胺/梭甲基澱粉的質量比為1 : 0一0 . 08 : 0 . 2時,復合顆粒電流變液的力學值隨甲酞胺含量的增加而升高;當甲酞胺與蒙脫土的質量比為0 . 08時,在2kv / ~的電場作用下,其電流變液的屈服應力值達8 . 3kpa ,是相同條件下的蒙脫土/梭甲基澱粉電流變液力學值的3 . 2倍,而當電場強度為3kv / mm時,其電流變液的屈服應力值達12 . 0kpa ,是相同條件下蒙脫土/梭甲基澱粉電流變液力學值的2 . 4倍。Continuously hot - dip coated strip and sheet of steels with higher yield strength for cold forming - technical delivery conditions
冷成形用高屈服強度鋼連續熱浸鍍帶材和薄板材.交貨技術條件Experimental results indicated that the polypropylene fiber can improve the workability of concrete availably, and can increase the presentation quality of structures with the voids and pits decreased ; the cracks of beam are controlled effectively, the width and length of crack decreased, the dispersibility of crack in beam face improved, and the ductility of beam increased ; and the cracking load of reinforced concrete beam is increased, the amplify up to about 30 %, simultaneity the ultimate bear capacity increased
試驗研究表明,使用聚丙烯纖維后,能有效改善新拌混凝土的和易性,並能增強混凝土構件的外觀質量,減少構件表面蜂窩、麻面、氣孔、細小裂紋等;同時,在破壞試驗過程中發現梁的裂縫能得到有效控制,裂縫寬度減小,裂縫的發展高度降低,裂縫的條數增加,提高了梁截面的裂縫分散能力,增強了梁中混凝土的韌性;提高了鋼筋混凝土梁的開裂荷載,幅度可達30左右,增強了結構的延性,提高了結構的抗裂性能和屈服荷載。In terms of strength and ductility, the concept of specified yield point is put forward. based on the principle that under the same condition ( that is, the size of cross section, material strength and reinforcement ratio are identical ), the resultant ultimate moment must be identical, the compression failure of frp reinforced concrete beam is equal to the tension failure for the viewpoint of design and calculation
從強度與延性兩方面的綜合考慮,提出了纖維增強塑料筋名義屈服點的概念,對發生受壓破壞的纖維增強塑料筋混凝土梁,按照同樣條件下(截面尺寸、材料強度、截面配筋率等均相同)截面承載力相等的原則等效轉化為受拉破壞進行設計與計算,以此確定纖維增強塑料筋的強度折減系數_ f 。Hot - rolled products of structural steels - part 6 : technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
結構鋼熱軋產品.第5部分:在冷淬和回火條件下的高屈服強度結構鋼扁平軋材交貨技術條件分享友人