梯度平板 的英文怎麼說
中文拼音 [tīdùpíngbǎn]
梯度平板
英文
gradient plate-
With the focus on the structure and components character of plate metal / ceramics graded coating, this paper extends and improves the thermal elastoplastic analysis model of trilayered materials derived by suresh et al and builds the theoretical model of thermal elastoplastic stresses analysis of plate metal / ceramics graded coating, and this paper also analyzes the thermal elastoplastic stresses and deformation of metal / ceramics graded coating
本文針對平板狀金屬陶瓷梯度塗層的結構和組成特徵，推廣和完善了suresh等人的三疊層材料的熱彈塑性分析模型，建立了平板狀金屬陶瓷梯度塗層熱彈塑性應力分析的理論模型，對金屬陶瓷梯度塗層的熱彈塑性應力和熱彈塑性變形進行了分析。Analysis of functionally graded plates in cylindrical bending using hybrid differential quadrature method
混合微分求積法在功能梯度材料平板柱形彎曲問題中的應用Cylindrical bending of functionally graded plates with arbitrary distributions of material properties under arbitrary loading are studied using hybrid differential quadrature method ( hdqm )
摘要利用混合微分求積法，對任意荷載作用下不同材料梯度分佈的功能梯度材料平板柱形彎曲問題進行了分析。Firstly, this paper describes the optimization problem of thermal stress of fabrication process and steady work process for the hollow cylinder and the infinite plate. then, thermal stress distribution is calculated making use of theoretical formulation and the results can be validated by finite element method. in optimization, the restriction condition is heat insulation performance and the objective function is danger coefficient
本文首先對平板結構和圓筒結構梯度塗層在制備過程和穩定工作狀態下的熱應力優化設計問題進行描述，然後分別用解析法求解兩種結構的梯度塗層在制備過程和穩定工作狀態下的熱應力分佈，並採用有限元方法驗證了熱應力分佈的結果，在優化設計時，以危險系數為目標函數，以塗層的隔熱性能為約束條件進行設計。For the optimization problem of fgms fracture performance, this paper fundamentally studies the fgm coating plate with interface edge - cracks, and establishes the approximate analysis method of the driving force for interface edge - cracks growth - energy release rate. this paper considers energy release rate as objective function and the optimization problem of fgms fracture performance is carried out by the paper mention optimization scheme
關于梯度材料破壞性能的優化設計問題，本文對含邊界界面裂紋的平板狀梯度塗層進行了初步的研究，建立了邊界界面裂紋擴展驅動力- -能量釋放率的近似分析方法，以能量釋放率為優化設計目標函數採用本文提出的優化設計方案對梯度材料的破壞性能進行優化設計。Furthermore, the higher the impact velocity, the smaller the extended wave ' s front while the higher the peak velocity. at the same time, the thickness off target should also be in accord with the impact velocity. finally, experiments of quasi - isentropic loading to aluminum targets with lithium fluoride windows via w - mo - ti - mg system flier - plate with graded wave impedance, having been fabricated by sps, were performed on a two - stage light gas gun
使用sps制備出平行度好、整體緻密的、 w - mo - ti - mg系準連續波阻抗梯度飛片材料，利用二級輕氣炮進行了w - mo - ti - mg系波阻抗梯度飛片材料的準等熵特性的實驗研究，成功實現了對帶窗口材料的al靶板的準等熵壓縮。Simulation results for non - isothermal flow pass plate have been shown. the spatial correlations in a fluid subjected to an external temperature gradient have been computed by using cellular automata simulations of a simple lattice - gas model with temperature. but, this theory is found limitedly applied to mechanics
並給出了平板非等溫流體繞流流動現象的模擬結果；通過採用一個含有溫度的簡化格子氣模型，用細胞自動機方法，模擬計算了服從于外部溫度梯度的二維流體中的平衡與非平衡空間相關函數，數值結果表明：該方法的計算結果和由漲落流體動力學理論的預言在是性上是完全符合的； bernsdorf等人用ca討論在復雜障礙物情況時的流體流動問題。The demarcation point of, which is the parameter in erf ' s yield stress equation, is 2. 0. for, the dynamic characteristics of the clutch are remarkably different from those for. thirdly, the linear stability of plane shearing flow with non zero pressure gradient is studied
論文第三部分對電流變液非零壓力梯度平板剪切流動的穩定性進行了分析，提出流場對屈服應力達到飽和的概念；並得出平板壁面剪切運動以及電流變液屈服應力的提高，都將使流動穩定性增強的結論。All of the results indicated the turbulent boundary layer had been turned into the laminar layer. the skin friction coefficient drops rapidly. this result not only proved the phenomenon of reverse transition had occurred, but also showed that this condition was drag - reducing condition
實驗結果表明板面附近的流動已由湍流流動轉變為層流流動，同時平板表面的摩擦系數較沒有溫度梯度時有大幅度下降，不僅證明了邊界層逆轉捩現象的存在，也說明了這種條件起到了減阻的效果。Mechanics model on anti - plane fracture of anisotropic functionally graded aterials plate
各向異性功能梯度材料板反平面斷裂問題的力學模型Exact solutions for functionally graded piezothermoelectric plates in cylindrical bending
功能梯度熱釋電材料平板柱形彎曲問題的精確解The low re k - model in software phoenics3. 3 were applied to simulating indoor air temperature field in this two kinds of heating room contrastively. it shown that temperature gradient at human altitude in floor heating room is lower 3 ~ 4 c than radiator heating room, temperature adjacent out wall and out window near by radiator is higher 6 ~ 7 c than mean indoor temperature, temperature different of room top with mean indoor temperature in top floor radiator heating room is higher 1 ~ 2 c and thickness is 0. 3 ~ 0. 5m thicker than floor heating room
結果顯示：在人員活動高度區域內，低溫地板輻射供暖房間的室內空氣豎向溫度梯度比散熱器供暖房間小3 4 ；在散熱器供暖房間內，靠近散熱器的外墻附近和散熱器上部的外窗附近空氣溫度高於室內平均空氣溫度6 7 ；在頂層房間，散熱器供暖房間頂部溫度與房間平均溫度之差比低溫地板輻射供暖房間高1 2 ，高溫區厚度比低溫地板輻射供暖大0 . 3 0 . 5m 。The influence of material property distributions on structural response of the plate to mechanical stimuli is studied through examples
通過算例，分析了在機械荷載作用下，材料不同梯度形式、平板上下表面材料性質差異對功能梯度平板結構響應的影響。分享友人