植入位置 的英文怎麼說

中文拼音 [zhírùwèizhì]
植入位置 英文
implantation site
  • 植 : Ⅰ動詞1. （栽種） plant; grow; cultivate 2. （樹立） establish; set up Ⅱ名詞（姓氏） a surname
  • 入 : Ⅰ動詞1 （進來或進去） enter 2 （參加） join; be admitted into; become a member of 3 （合乎） conf...
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 植入 : implantation; embedding植入術[法國] [醫學] implantation; 植入物 [醫學] implant
  1. Results n 45 patients with secondary suspensory intraoular lens implantation, the iols ' position were stable and the visual acuity had been improved

    結果45例二期懸吊式人工晶狀體植入，人工晶狀體位置穩定，視力均有不同程度提高。
  2. Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc

    本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。
  3. We attracted insect pests with common 20w black light which was used by pest control services, adjusting insect pests " posture by running water, installed color camera at proper position, and designed illuminating system so that we could obtain distinct insect pest image. finally, insect pest image was inputted into the computer by color image acquisition card

    採用植保站常用的20w黑光燈誘集害蟲，設計裝置使害蟲落入流動的水中，藉此調整害蟲的姿態；選擇合適的位置，安裝彩色攝像頭，並設計照明系統，盡可能保證獲得的害蟲圖像清晰；經彩色圖像採集卡將害蟲圖像輸入計算機。
  4. The question is how much of the problem of stent failure maybe the result of stents not being put in right or maybe they are not being expanded enough to fit firmly in the artery

    現在的問題在於支架支架的治療效果，而不是其固植入位置不正確，或是其擴張不足不能在動脈上很好地固定。
  5. When ahtavb were impianted in diff6rent position the stability were decreased especiaily in oblique and iaterai position comparing with the neutrai position ( p < 0. 01 )

    不同植入位置中，中立位置入應變最小、強度最大，斜放及側位植人對脊柱的穩定性影響最大，與中立位置入相比具有顯著性差異中卅
  6. Three ( 3 ) normally closed, automatic - reset, thermostats connected in series shall be embedded in adjoining phases of the stator windings

    三（ 3 ）個串聯的、能夠正常關閉、自動重置溫控器應該植入定子繞組的相鄰相位上。
  7. Though the technique of nuclejc transformation in plants has been developed and used widely, some problems in genetic information have not been resolved. for example, because the nucleic genome is so big and complicated that the integration sites and copies of foreign gene can not be controlled accurately, the expression of transferred genes is inefficient as a result of gene silencing or position effect. in nucleic transformation, furthermore, the transfer of multigene is difficult, and only after the prokaryotic genes undergo modification are they expressed in high plants

    植物的細胞核轉化技術已發展成熟並得到廣泛應用，但核基因組的遺傳轉化仍存在一系列至今尚未解決的問題：例如由於核基因組大，背景復雜，外源基因的整合位點和整合的拷貝數難以人為控制，造成鄭州大學2003年博士學位論文杜氏鹽藻（ dunaliellasalina ）葉綠體轉化研究外源基因表達效率低，容易出現基因失活、基因沉默、位置效應等現象;同時轉入多個基因時操作步驟過于復雜，所表達的原核基因必須經過修飾改造，環境安全難以保證等。
分享友人
分享到 Line

分享到臉書