極性對稱軸 的英文怎麼說

中文拼音 [jíxìngduìchènzhóu]
極性對稱軸 英文
polar symmetry axis
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 對 : Ⅰ動詞1 （回答） answer; reply 2 （對待; 對付） treat; cope with; counter 3 （朝; 向; 面對） be tr...
  • 稱 : 稱動詞（適合; 相當） fit; match; suit
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  1. Symmetries are existed in oxy and oyz planes for horizontally and vertically polarized waves, i. e. one ' s h - polarized case is the same as the other v - polarized one. while the expectations of the rotatory axes oriented in oxz plane are complement, one ' s h - polarized case is the same as the other v - polarized one

    平面oxy和平面oyz對于兩種偏振極化入射波時存在著對稱性，一者的水平極化與另一者的垂直極化情況相同；而oxz平面內旋轉軸的平均取向的期望互余時，一者的水平極化與另一者的垂直極化時的情況相同。
  2. On the base of the character of hemisphere continuously vibrating, the method of actuation and measuring, the asymmetry compensating process and the measuring limit were studied, the control loop and the parameter design were introduced, which will be prepared for the future circuit design and the automobile security application

    本論文主要是在半球連續振動特性的基礎上，對陀螺儀的驅動及感測方法、非軸對稱的補償方法及感測極限進行研究，並詳細介紹其控制迴路與其參數的設計，為以後電路設計和面向汽車安全的應用打下了堅實的理論基礎。
  3. Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure

    試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。
  4. Firstly, the basic character of the remote filed eddy current is simulated and analyzed in case of two - dimension axial symmetry which approves the existence of remote filed eddy current phenomenon ; the full circumferential defect model is investigated to approve the feasibility of using the rfec techniques to detect the position and depth of defect ; the pit corrosion 、 circumferential and axial crack models are simulated, and the defect character based on voltage plane polar plot and the changes of phase and amplitude are analyzed to supply the standard for defect reconfiguration

    首先，在二維軸對稱情況下模擬與分析了遠場渦流的基本特性，證實了遠場渦流現象的存在;對全周向缺陷的遠場渦流檢測進行了詳細研究，證實了遠場渦流檢測缺陷位置和深度的可行性;對點狀腐蝕、軸向與周向裂紋三種非軸對稱缺陷進行三維有限元模擬，利用相位差和幅值變化曲線與電壓平面極坐標圖對缺陷特徵進行分析，為缺陷形狀重構提供了依據。
  5. Cylindrical cup is a typical axial symmetrical part, though the deformation of material is simple in drawing process, but during the drawing process, exists a lot of influence factors ( including workpiece material character itself as well as each technological parameters ), and they restrict mutually between the factors. so how to calculate the limiting drawing rate of a cup becomes a complicated nonlinear and multi - gene question. to predicting limiting drawing rate of the cylindrical cup accurately indeed is a very complex subject

    筒形件是典型的軸對稱拉深件，在拉深過程中材料的變形雖然相對簡單，但是在生產過程中，由於影響因素很多（包括工件材料本身性能以及各個工藝參數） ，且各種因素之間相互制約，故如何準確地計算筒形件拉深極限就成為一個復雜的非線性多因子問題，要真正準確預測筒形件極限拉深系數也是一個非常復雜的課題。
分享友人
分享到 Line

分享到臉書