極板對 的英文怎麼說

中文拼音 [jíbǎnduì]
極板對 英文
plate pair plate couple
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 對 : Ⅰ動詞1 （回答） answer; reply 2 （對待; 對付） treat; cope with; counter 3 （朝; 向; 面對） be tr...
  1. Mems ( micro electromechanical system ) has become one of the most rapidly development technologies. along with the rapid development of mems techniques, capacitive sensor is used widely whose capacitance changes small, which has put forward the new request to the measurement technique. the common measure for capacitance measurement is that convert capacitance to voltage, electric current or frequency. the area of polar plate of the capacitor becomes smaller and smaller, and the total capacitance of micro capacitive sensor is usually several pico farad only. as a result, its change amount is smaller

    Mems （ microelectromechanicalsystem ）近年來發展最快的技術之一，隨著mems技術的快速發展，電容式加速度計的電容變化變化量越來越小，對檢測技術提出了新的要求。在電容式傳感器中，常用電容檢測電路是將其轉換為電壓、電流或者頻率信號。目前的微型電容傳感器的極板面積變得越來越小，電容總量只有幾個pf ，變化量就更小。
  2. This paper researches on the practical current and potential distributions on the positive and negative plates of automotive batteries in the course of their formation processes by the means of an in situ electrochemical scan, and then studies the influences of the formation and also the additives on the performance of the automotive plates

    本文利用電化學掃描方法研究鉛酸蓄電池正負極板在化成過程中電流密度和電位分佈及化成對極板電性能的影響。同時分析了正負極添加劑的性質及其對極板性能的影響。
  3. Combined with development of the products, the research emphasis in this paper is focus on the studies of the high - rate discharging performance at different temperature. 1. in the research of the discharge performance with high rate, the results of different effects including thickness of positive electrode, materials of hydrogen storage alloy, concentration of the electrolyte and separators

    論文在實現研究目標的過程中，結合產品的研製，重點對電池的高倍率放電性能和溫度性能進行了研究：一、在提高電池大電流放電性能的研究中，比較了不同正極板厚度、不同貯氫合金材料、不同濃度電解液及不同材料隔膜等對電池大電流放電平臺的影響，並從電極反應動力學和多孔電極的角度分析了極板厚度對電池高倍率放電的影響。
  4. Carbon nanotubes ( cnts ) were activated by co2 and air under different durations, then were used in polarizable electrodes of electric double - layer capacitors ( edlcs )

    摘要對碳納米管粉體在高溫下進行空氣和二氧化碳活化處理，並用於製作雙電層電容器極板。
  5. Firstly, for the system of moulding board and support frame in construction the side pressure and screws are analyzed. the material and structure form of support frame are discussed. the design of support frame uses the method of limited state, and also it analyses the integer stability, part stability, and single stability, and then proposes the load analysis of multi - level support frame

    首先，針對轉換層梁模體系及支撐架施工，重點分析了轉換層結構現澆混凝土對模板側壓力值及模板對拉螺桿的計算；討論了轉換層支撐體系的形式及構造，詳細論述了基於極限狀態設計的支撐架計算方法，包括縱橫向水平桿的強度驗算、立桿的整體穩定性、局部穩定性、單肢桿件穩定性等驗算，並提出了多層支撐架的施工荷載計算方法。
  6. The influence of structure design of pb - plated reticulated sic current collector on the plate design parameters and utilization efficiency of pam of lead - acid batteries was studied

    摘要研究了鍍鉛泡沫碳化矽集流體的結構對鉛酸蓄電池極板的設計參數、正極活性物質利用率的影響。
  7. From the experiment we have found out that the carbon fibre can improve the anode performance when it was used as pam additive and meanwhile it can have some benefits to the anode life. when its content at 0. 2 - 0. 3 % in pam can achieve its best result and under this situation it can improve the utilization of pam by 5 % at different discharge current. carbon fibre and sulfate sodium is used as complex pam additive and its effect is better than that of carbon fibre which alone is used as additive

    通過實驗我們發現，碳纖維作為鉛酸電池的正極活性物質添加劑能提高鉛酸電池正極的性能，並且對電池正極板的壽命有一定的好處，當碳纖維在正極活性物質中的含量為0 . 2 0 . 3能得到最理想的效果，這個時候能在各種不同的放電電流下提高正極活性物質的利用率5左右，並且能夠使極板的電化學阻抗降低。
  8. Sub - c mh - ni power batteries were prepared with excellent electrochemical performance based on the research of the high rate performance at different temperature. the change of temperature, impedance and weight loss was investigated in the process of recycle at high rate. it showed that the discharge time is 5. 9min at 10c and the middle voltage is 1. 05v

    三、根據對電池大電流和溫度性能的研究，研製了具有較好電化學性能的動力型鎳氫電池，並分別測試了電池在大電流循環過程中的溫度、內阻、重量和正負極板等的變化情況，以此分析引起電池性能衰減的原因。
  9. ( 3 ) by using an elastic - plastic material model, the nonlinear analysis is taken on the rectangular tube and simply supporte d plate, and the ultimate carrying load capacity pu is obtained. the results show that the buckling mode is in accordance with the assumption of elastic analysis, and so shows the ultimate mode

    （ 3 ）採用彈塑性模型，考慮幾何非線性理論，利用ansys軟體對矩形鋼管考慮板組相關屈曲影響和不考慮相關屈曲影響（將矩形管板件按四邊簡支板對待）兩種情況進行了屈曲後分析，分別得出其極限承載力p _ u ，並分析了矩形管的屈曲過程。
  10. A driving signal with a dc bias voltage and ac voltage is usually necessary for sensing very small capacitance. the reliable operation conditions of the capacitive sensor for foreign acceleration had been researched with the assumption of the parallel comb plates. but the comb plates are actually not parallel for the reason of the drie process

    前人在研究外界加速度信號對傳感器的作用時，假定驅動信號產生的靜電力作用在平行梳齒電容極板上，但是，在用drie工藝對硅進行刻蝕時會產生側蝕效應，從而得到的梳齒電容有一定的傾斜角度。
  11. On the aspect of errors analysis of hrg, a brief introduction of the close - loop detection theory of hrg is present first. later the expressions of close - loop detection errors are deduced in theory. the impact of stimulating signals, turning speed, outside appended oscillation, the location & area of electrodes, and the current loss in capacitor is considered, and the primary analysis of error compensation is given

    在半球諧振陀螺誤差分析方面，本文從半球諧振陀螺的閉環檢測原理出發，對半球諧振陀螺閉環檢測誤差進行了分析和推導，考慮了激勵信號、轉動速率、外界附加振蕩、電極位置及極板面積和電容傳感器等因素造成的陀螺誤差並對誤差補償進行初步分析。
  12. 3d numerical simulation of finete element method ( fem ) program is used to calculate and analyse the distribution of stress and strain during hydrobulging, the ovality of single - curvature polyhedron after being hydrobulged while the dimension of polar plate of single - curvature polyhedron without the flaw of imaginary crack changes

    摘要利用三維數值模擬方法，對假想無裂紋的單曲率多面殼體模型上極板尺寸發生變化時脹形過程中應力應變的分佈、脹形結束后多而殼體的不圓度等進行了計算和比較。
  13. The article relates that the tool ' s measurement precision has been improved by applying cycling acquisition method, self calibration function and phase - sensitive detector. the image coverage rate is improved and reached to 60 percent by increasing the number of pad ' s buttons. the tool carried out two logging functions : fast - scanner mode and dip mode

    本文敘述了採用循環採集法、自刻度功能、相敏檢波等方法提高了儀器的測量精度；通過增加極板電扣的數量將圖像覆蓋率提高到60 ；實現了快掃描、傾角兩種測井模式；將測斜短節與預處理短節合二為一，縮短了儀器長度；去除了零伺服控制系統，簡化了電路；用fpga晶元對採集控制器重新設計。
  14. For example, the silicon is etched anisotropically in the koh solution, the lucent al film is made with the magnetron sputtering system, the pressure hole is drilled by the supersonic stiletto machine and the silicon and the glass are bonded with electrostatic bonding setup

    例如， koh溶液對硅的各向異性腐蝕，磁控濺射臺製作光亮的鋁膜，超聲打孔機製作導壓孔，靜電鍵合裝置對硅島膜與玻璃極板的陽極封接等等。
  15. After analyzing the structure and specialty of capacitance sensor, simulating and calculating the sensor ' s size. then construct a new style capacitance sensor with 16 electrodes combined and floated

    在分析了電容傳感器的結構特點之後，對傳感器結構尺寸進行模擬計算，建立新型的16極板組合浮置式電容傳感器。
  16. 4. a fitted equation was given to ultimate load of geometrically similar slabs with size effects taken into account

    4 、考慮材料尺寸效應，擬合出幾何相似的板對于極限荷載的相似規律。
  17. Formation is the first charge for the plates, therefore, it has an direct effect on the performance of the batteries and its life

    化成其實就是對電池極板的第一次充電，所以化成的好壞將直接影響到生產的蓄電池性能和使用壽命。
  18. With a study in depth on the charging process the author reached the following understanding : the ideal charging current at a specific moment is dependent on the amount of active material on the battery plates and the reactive environment, that is to say, the charging current should follow a j. a. mas proposed acceptable curve or optimal curve ; the polarization is unavoidable but controllable in charging and discharging

    筆者主持的原煤炭部優秀青年基金項目《輕型智能充電裝置研究》即代表這種關注。筆者通過對充電過程的分析得到如下理解： -任何時刻的理想充電電流取決于當時極板上的活性物質的多少及其周圍反應環境，充電電流的變化應遵循馬斯（ j
  19. To the object of two - flow, we trace its dynamic character and measure its correlated parameters by eight - electrode capacitance sensors. then turning the dispersed information to the integral information by sufficiently using information of object. the simulation experiment proved that this information fusion arithmetic can recognize the flow type precisely and timely

    針對管道中的兩相流被測對象，利用8極板電容傳感器對其在管道中的動態特性進行追蹤，並測取相關參量，利用信息融合演算法處理所獲得的信息，充分利用傳感器信息資源，將分散的傳感器信息融合成所測流型的整體信息。
  20. In order to design a reliable cathodic protection system for a ballast bank, it is necessary to develop a quantitative model for the shielding effect due to the inner structures on the protection current in a cathodic protection system of a ballast tank through a lot of numerical simulation or practical measure

    需要通過大量的數值模擬計算或實測，得到各種擋板對保護電流的屏蔽效應的定量化模型，以確立新的適合於壓載艙的陰極保護設計的技術體系。
分享友人
分享到 Line

分享到臉書