極限剪力 的英文怎麼說

中文拼音 [jíxiànjiǎnlì]
極限剪力 英文
ultimate shear
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 剪 : Ⅰ名詞1 （剪刀） scissors; shears; clippers2 （姓氏） a surname Ⅱ動詞1 （用剪刀等使細的或薄片的東...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 極限 : 1 （最高的限度） the limit; the maximum; the ultimate limit; limitation; extremity; tipping point...
  1. Based on the analysis of mechanism for joint region, the " frame - wall " and " aslope compression stub column " mechanical models and yielding patterns of core zone of the joints are set up. the shear load - carrying formulation for joint core zone is also given in terms of plastic ultimate analysis. and then, the comparisons between the formulas given in this paper and that of chinese design code ( draft ) and nonlinear fem as well are presented

    對節點核心區的抗剪，通過受力機理的分析，建立了鋼「框架剪力墻」加混凝土「斜壓短受力體系及其屈服機制，根據塑性極限分析，給出了節點核心區抗剪承載力計算的迭加公式， 《規程》公式和非線性有限元近似模擬分析結果進行了比較。
  2. On the basis of investigations into the progressive yield process and the possible failure modes of rcc gravity dams, the quasi - elasticity design limit state of the ctrtical stability criterion is proposed and the real working state of the dams designed according to the ctriterion is discussed. a check formula using the material strength reducing factor as the safety index and a simplified formula similar to against sliding stability fromula are derived. finally, the corresponding design safety factors are given by using fem calculations with various influence parameters to be taken into account

    本文在研究碾壓混凝土重力壩漸進破壞過程和可能失穩方式的基礎上，提出了以準彈性臨界作為穩定臨界準則的設計極限狀態，分析了按該準則設計的大壩的實際工作狀態，導出了以準彈性強度儲備系數為設計安全指標的審查公式以及形式與抗剪斷公式相同的簡化公式，探討了定量計算考慮各種因素影響的相應設計安全系數的合理取值，並與現行規范方法進行了比較
  3. The consequence is, when the majority of structure does n ' t enter yield habitus, but the position of belly - board has been reached the ultimate habitus, it lead to material waste of the other positions, we should pay attention to the disastrous result it will bright to us

    它帶來的後果就是當結構的大部分處于彈性狀態時，箱梁腹板處由於剪力滯效應一般最先達到強度極限狀態，導致腹板間材料的抗力沒有得到充分的使用，如不引起重視會帶來災難性後果。
  4. Based on the philosophy of capacity design, the formulas of overstrength of coupled - shear wall were established to offer the theoretical references for the evaluation on the seismic performances of the shear - wall structures designed by current building codes based on bearing capacity method under severe earthquake, which has been proved correct by the results of nonlinear full range analysis

    摘要基於能力設計原理，建立了聯肢剪力墻結構極限承載力的超強計算公式，為按現行規范以承載力設計的剪力墻結構評估其在罕遇地震下的抗震性能提供理論依據，並結合實際工程中剪力墻的計算和非線性分析結果，證明了本文方法的正確性。
  5. Based on the pseudo - static experimental results of nine abnormal joints, the damage process of abnormal joint is divided into four stages of original crack, entire crack, ultimate state and failure, the effect of axial force ratio, stirrup ratio and height of column section on seismic behavior of abnormal joint are discussed, the conclusion that anti - shear capacity of abnormal joint are studied in entire crack state by studying the minor core of abnormal joint is made, the calculating formula for anti - shear capacity of abnormal joint is proposed with a view to asymmetry in stirrup yield

    摘要根據9個鋼筋混凝土框架異型節點試件的擬靜力試驗結果，指出異型節點受力過程分為初裂、通裂、極限和破壞4個階段；討論了軸壓比、節點核芯配箍率、柱截面高度變化對異型節點抗剪性能的影響；提出應考慮節點核芯區箍筋屈服的不均勻性並在通裂狀態下以「小核芯」為分析單元來研究此類節點抗剪承載力的建議；最終給出了異型節點抗剪承載力的計算公式。
  6. Its hysteretic curve is plumper, its ductility coefficient and energy dissipation capacity have been improved remarkably. the inclined staff of the steel bar truss has a restraining faction to the development of the crack, and the phenomena is that there has more crak and larger distributing area on the shear wall, which is an important token of the improved seismic capacity. concealed steel bar truss has the faction of increasing the height of plastic hinge area, which is another important token of

    研究結果表明:內藏鋼桁架高剪力墻與普通高剪力墻相比:屈服荷載和極限荷載均比顯著提高;屈服剛度明顯提高;其滯回環相對飽滿，延性系數及耗能能力顯著提高;內藏鋼桁架高剪力墻，其鋼桁架斜桿對裂縫發展有控製作用，現象是墻體上的裂縫較多、分佈域較廣，這是抗震耗能能力增強的重要表徵;內藏鋼桁架高剪力墻有增大底部塑性耗能區域的作用，這是抗震耗能能力增強的另一重要表徵;內藏鋼桁架還有顯著提高抵抗剪力墻基地剪切滑移能力的作用。
  7. In this paper, based on the analysis of the rlem of theory foundation, computing method, preference, applicability, etc, we anatomized the rlem of three self - deficiencies and six scarcities. moreover, we adopted the parallel ways of contrasting the rlem with the fem and applied it to analyzing the impact of slide block of elasticity and plasticity, slip surface of coefficient and slip bed of elasticity, plasticity upon the stability of slope and in the plain linearity slope, the plain refracted line slope and the plain arc slope. in addition, we discussed the warp of between the lem of ( sarma, janbu, order, bishop, morgenstera - price, etc ) and the fem of result and the distributing of positive stress and shear stress on the slip surface

    本文從剖析剛體極限平衡法的理論基礎、計算方法、參數選取、適用條件等方面入手，剖析了剛體極限平衡方法的3點自身缺陷和6點不足，並在此基礎上採用了剛體極限平衡法（平面滑動破壞法、 sarma法、傳遞系數法、普遍條分法、 janbu法、 bishop法、 morgenstern - price法）與大型有限元法對比研究的方法，分析研究了平面直線型滑坡、平面折線型滑坡、平面圓弧型滑坡在漸進破壞中邊坡的滑體彈塑性參數、滑麵塑性參數） 、滑床的彈塑性、以及極限平衡法無法考慮開挖應力釋放等因素對邊坡穩定性的影響與滑動面上的正應力、剪應力分佈規律、安全系數的解答的差異。
  8. On the basic of former research men ' s experience, 18 experimental members ( including 9 simple beams and 9 restrained beams ) are designed and tested. in the experiment, phenomena are observed and record by taking photos in the whole process from the first crack appears to test members crash completely, experimental data is attained including load values of crack - appear load, critical load and terminal load, stress values of reinforcing steel bar stress, compressed concrete stress and beam flank stress and values of deflection etc. by analyzing the crack ' s appearing and developing form and stress values of concrete and steel bars, the crash modes of test beams are defined ; shearing force - deflection curves are contrasted and analyzed ; the effects on shear strength of the three factors as shear span ratio, concrete strength and restraining moment are also analyzed

    借鑒已有試驗的經驗，本文設計和完成了對18根超高強混凝土無腹筋梁（包括9根簡支梁和9根約束梁）在集中荷載下抗剪強度的試驗，觀察了試件從裂縫出現到完全破壞失去承載能力全過程的試驗現象並通過拍照進行記錄，獲得了試件的斜裂縫出現荷載、臨界斜裂縫荷載和極限荷載等荷載值和縱筋應變、混凝土受壓應變和梁側混凝土應變等應變值以及撓度值等。
  9. Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure

    試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。
  10. Through comparing and analyzing of bearing capacity, development of crack and strain of reinforced, the results show that the load - deflection plots f or specimens from the finite element analysis agree well with the experimental data, and choosing the rightful stress - strain relationship, utilizing ansys program, the test process can be well simulated. at the same time, making used of the program, the traditional shear wall is analyzed. it shows that comparing with the traditional shear wall, the hollow shear wall ' s cracking load drop 16 %, yield load and failure load drop 13 %, stiffness drop 13 % ~ 22 %

    其次在試驗的基礎上，將試驗手段、有限元數值模擬方法和理論分析結合起來，利用有限元程序ansys對其中的兩片墻板進行非線性有限元分析，並對前後的承載性能，裂縫發展、鋼筋應變進行了比較和分析，結果表明有限元節點模型分析的荷載-位移曲線和試驗測得數據符合良好，選用合理的材料本構模型，利用ansys可以較好的模擬試驗過程；同時利用有限元模型對比分析了普通剪力墻和空心剪力墻，空心剪力墻與普通剪力墻對比，其開裂荷載下降16 ，屈服荷載、極限荷載下降13 ，剛度下降13 22 ，開裂至屈服、屈服至極限荷載階段的剛度衰減規律與普通剪力墻基本一致，空心剪力墻的後期剛度比較穩定。
  11. At first, a limited equilibrium method is proposed for the stability analysis of soil nailing. the effective of the shearing of soil nail is discussed

    首先採用極限平衡分析的方法對土釘支護的使用進行理論分析，探討土釘剪力對一般型土釘支護作用的補強效果。
  12. This paper has put forward such one, i. e. to use the dimensional angle iron framework to strengthen the center of the knot in order to add its degree of toughness and stiffness, improve its crack load and aggrandize its ultimate deformation

    本文提出了一種提高節點抗震性能的新方法? ?用空間角鋼骨架對節點核心區進行加強，以增大節點的強度、剛度，提高節點的抗剪、抗裂性能，並增大節點的極限變形能力及延性性能。
  13. Considering the shear strenth of unsaturated soil, the method of analysis of limit equilibrium has been approved and it can be used in the analysis of the stability of saturated - unsaturated slopes

    在考慮非飽和區土體抗剪能力的情況下，對傳統的邊坡極限平衡分析方法作了改進，使之可應用與飽和?非飽和區土體的邊坡穩定問題。
  14. ( 2 ) 3d - fem analysis for the load - bearing capacity of the stud connector as the prevailing method to determine the shear rigidity and the limit load - bearing capacity of the shear connector is the push test, which is time consuming and laborious, in this thesis the push tesi specimen of the stud connector is simulated through the non - linear analysis module of the msc / nastran and the numerical analysis results are in good coherence with that of the practicality lev ; as a result, the shear rigidity and the limit load - bearing capacity of the stud connector can be determined by the finite element method and only a few practicality verification tests

    （ 2 ）栓釘型剪力鍵承載力的3d - fem分析針對當前剪力鍵一般通過費時費力的推頂試驗來確定抗剪剛度和極限承載力的狀況，本文利用msc nastran非線性模塊實現了對栓釘剪力鍵推頂試樣的數值模擬分析，數值計算結果與試驗結果能夠很好吻合。這使得通過有限元方法的模擬和少量實物試驗的驗證，就能確定栓釘剪力鍵的剪切剛度和極限承載力，可以大大節省時間和經費。
  15. Based on the result of failure by shear of recycled concrete beams and using the ultimate equilibrium theory, a formula for the shear strength of recycled concrete beams is recommended

    根據13根再生混凝土梁的剪切破壞結果，依據極限平衡理論，提出再生混凝土梁受剪承載力的計算公式。
  16. Observing the mechanics and effect of the new strengthening method with test and finite element method is supposed to offer a guide for technology and become valuable in theory and practice. both compression test, including four reinforced and three control specimens, and shear - compression test, including nineteen reinforced and four control specimens are being studied in this paper. the research on the curves of load - strain, load - deflection and hysteretic shows that the transverse translation of the reinforced columns is well controlled with an upgrading of both ductility and ultimate bearing capacity ( ubc )

    本文對4根鋼絲網外噴高強砂漿加固鋼筋混凝土柱和3根對比鋼筋混凝土柱進行了軸壓試驗研究，並對19根加固鋼筋混凝土柱和4根對比鋼筋混凝土柱進行了剪壓試驗研究；通過對試件荷載-應變曲線、荷載-撓度曲線和滯回曲線等的研究表明，採用該加固方法能有效的約束柱子橫向變形，並對提高鋼筋混凝土柱的極限承載力和延性有明顯的效果；同時根據理論及加固機理分析提出了適應於此加固方法的軸壓極限承載力計算公式。
  17. Using two different finite element models, compress and shear destroyed states, starting crack load and ultimate bearing capacity are obtained

    通過建立兩組不同的砌塊墻體有限元模型，分析了砌塊墻體受壓和受剪的破壞形態、開裂荷載和極限承載力。
  18. A simplified formula for the shear capacity of rc simply supported beam which strengthened with the cmmr is proposed in this paper. 3 、 the shear capacity of rc beam strengthened with cmmr is studied. though the test of fourteen simply supported reinforced concrete beams and five overhanging reinforced concrete beams with cmmr, it analyses the effects of shear - span ratio, web reinforcement ratio of cmmr, style of loading, preloading on strengthening, and compares them with rc beams using ordinary stirrup

    3 、根據本文進行了的14根混凝土簡支梁和5根混凝土伸臂梁的水泥復合砂漿鋼筋網抗剪加固試驗，分析了剪跨比、鋼筋網配筋率、加固形式以及持荷狀態等因數對整個構件極限抗剪承載力的影響，並與混凝土梁進行了比較。
  19. Some conclusions are revealed from these results : the bearing press capacity of concave concrete block wall is a little smaller compare to normal block wall, but the shear bearing capacity, the crack load and ultimate load are distinct lager than the later, and the amount of cracks are more than normal block masonry

    分析結果表明，凹形砌塊墻體受壓承載力比普通砌塊墻體的受壓承載力略低，而受剪承載力明顯高於普通砌塊墻體。凹形砌塊砌體與普通砌體相比，凹形砌塊墻體的開裂荷載、極限荷載明顯要高，砌體內的裂縫數量要多。
  20. A seismic shear capacity equation for ductility and non - ductility columns is proposed to amount for the reduced shear contribution of concrete as to the increasing of displacement ductility levels. 6. the behavior of columns * transverse displacement within yield hinge regions is also discussed based on truss - arch model. 7. the seismic shear capacity design equation of columns with various ductility levels is proposed in statistic method on the basis of test data collected from japan and china to simplify the equation resulted from truss - arch model

    對國內外試驗資料進行了統計分析，詳細分析了剪跨比、軸壓比及配箍特徵值對框架柱構件抗剪承載力的影響，得到了反復荷載下框架柱塑性鉸區域極限承載力計算的統計公式；在理論推導公式及統計公式的基礎上，參考國內外規范，首次管品武；鋼筋混凝土框架柱塑性鉸區抗剪承載力試驗研究及機理分析提出了鋼筋混凝土框架柱塑性鉸區域剪切承載力抗震延性設計實用公式。
分享友人
分享到 Line

分享到臉書