極限屈服值 的英文怎麼說

中文拼音 [jíxiànqūbìzhí]
極限屈服值 英文
limiting yield value
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 服 : 服量詞（用於中藥; 劑） dose
  • 極限 : 1 （最高的限度） the limit; the maximum; the ultimate limit; limitation; extremity; tipping point...
  1. After pretension 0. 1 strain and pretorsion to 14, whereas the strength limit keep on increasing in company with the pretorsional capacity

    其中屈服極限在預拉伸應變0 . 1后再預扭轉14后達到最大值，而強度極限隨著預扭轉量的提高不斷增大。
  2. The moment - curvature relationship chosen is assumed to have a horizontal branch beyond yield, with the moment remaining constant at the ultimate value

    所選用的彎矩曲率關系是假定超過屈服後有一個水平段，即彎矩保持在極限值不變。
  3. It is provided by the result of observing for the trial of pile, if the cast - in - place is constructed according to strict technological process, the limit load - bearing capacity of single pile is more larger then its calculational value, and under the function of the most trial loading, the frictional drag haven " t occur yield in every major loading layer, so the pile have greatly safety reserve in engineering

    樁試驗的觀測結果證明，按照嚴格工藝流程施工的鉆孔灌注樁，其單樁極限承載能力遠大於計算值；在最大試驗荷載作用下，各主要持力層均未出現摩阻力屈服現象，樁有較大的工程安全儲備。
  4. After pretorsion the successor tensile yield limit and strength limit both improved very highly, but the trend of the increase of the strength limit was suspended till the pretorsional capacity reached 17, when the pretorsional capacity was greater than17 ( prestrain value was 81. 19 % of total strain ), the successor strength limit rapid failed and approached the yield limit. this illustrate the a3 steel specimen translate from plasticity into friability after pretorsion strengthen. when the specimen was operated by tension - torsion action, the yield limit had very large improved, but the strength limit changed very little. furthermore, the trend of the increase of the strength limit was suspended till the pretension capacity reached 0. 25 ( prestrain value was 66. 93 % of total strain )

    A3鋼試件在預扭轉后，后繼拉伸屈服極限和強度極限均有很大提高，但強度極限的增大趨勢到預扭轉量為17為止，預扭轉量大於17 （預應變值為總應變的81 . 19 ）后強度極限迅速下降，與其屈服極限接近，這說明a3鋼試件經預扭轉強化后逐漸由塑性轉化為脆性。該預應變值為a3鋼試件的韌脆轉變點。 a3鋼試件在拉伸-扭轉作用下，屈服極限有很大提高，但強度極限沒有多大改變，而且，屈服極限的增大趨勢到預拉伸量為0 . 25應變（預應變量為總應變量的66 . 93 ）后就不再增加。
  5. Through comparing and analyzing of bearing capacity, development of crack and strain of reinforced, the results show that the load - deflection plots f or specimens from the finite element analysis agree well with the experimental data, and choosing the rightful stress - strain relationship, utilizing ansys program, the test process can be well simulated. at the same time, making used of the program, the traditional shear wall is analyzed. it shows that comparing with the traditional shear wall, the hollow shear wall ' s cracking load drop 16 %, yield load and failure load drop 13 %, stiffness drop 13 % ~ 22 %

    其次在試驗的基礎上，將試驗手段、有限元數值模擬方法和理論分析結合起來，利用有限元程序ansys對其中的兩片墻板進行非線性有限元分析，並對前後的承載性能，裂縫發展、鋼筋應變進行了比較和分析，結果表明有限元節點模型分析的荷載-位移曲線和試驗測得數據符合良好，選用合理的材料本構模型，利用ansys可以較好的模擬試驗過程；同時利用有限元模型對比分析了普通剪力墻和空心剪力墻，空心剪力墻與普通剪力墻對比，其開裂荷載下降16 ，屈服荷載、極限荷載下降13 ，剛度下降13 22 ，開裂至屈服、屈服至極限荷載階段的剛度衰減規律與普通剪力墻基本一致，空心剪力墻的後期剛度比較穩定。
  6. A material nonlinear finite element analysis for the cast - in - place reinforced concrete hollow slab that occurs from initial loading, cracking, yielding to failing is carried on. the cracking load, ultimate load, the displacement rules and the principal stress distribution rules of the hollow slab under the vertical loads are obtained. a material nonlinear finite element analysis for the single span hollow flat - plate floor is also carried on

    其次對空心板進行了從加荷、開裂、屈服直至破壞的全過程材料非線性有限元計算，得到了空心板在豎向荷載作用下的開裂荷載、極限荷載及位移和應力分佈規律；還對單跨無梁樓蓋進行了材料非線性有限元計算，通過分析主應力場明確了柱上暗扁梁的作用；有限元計算的結果驗證了以上的理論分析並得到了一些重要的結論，對改進現澆空心板無梁樓蓋的構造措施有重要的參考價值。
  7. At first, the experiment carried out by tianjin university has been analysed according to the " nonlinear balance trying calculation " method, and the values of yield load and ultimate load agree with the test result better, and the curve of bending moment - curvature, bending moment - deflection can agree with the results. the second, the simplified formula for evaluation the ultimate flexural capacity of cfrp strengthened rc members is presented according to the three probable failure modes ( compression failure ; cfrp rupture ; crushing of the concrete in compression before yielding of the reinforcing steel ). it is applicable to both singly and doubly reinforced rectangular sections, as well as flanged sections

    首先利用鋼筋混凝土非線性平衡試演算法對天津大學試驗進行了理論分析，所得分析值與試驗結果相比，加固梁的屈服荷載、極限荷載能夠很好地吻合，彎矩曲率關系曲線及彎矩撓度關系曲線較為吻合；其次，為了滿足實際工程的需要，根據碳纖維布加固構件可能發生的三種破壞形態（壓區混凝土壓碎破壞、碳纖維布拉斷破壞以及受拉鋼筋尚未屈服時壓區混凝土已壓碎破壞） ，區別三種鋼筋混凝土構件截面形式（單筋矩形截面、雙筋矩形截面、 t形截面） ，分別給出了碳纖維布加固混凝土構件抗彎承載力的簡化計算公式和適用條件，並進一步探討了這三種截面形式下進行加固設計和復核的步驟。
  8. For the obvious yield point of angle steel, the critical frictional resistance could be regarded as ultimate pullout capacity

    對具有明顯屈服點的鋼材，在實際施工中，可以把摩阻臨界值作為極限拉力。
  9. In this paper, the ductility of steel bar is expressed by ductility ratio b, the figure of dividing ultimate strain by yield strain. the ductility of section is expressed by ductility of section ratio, the figure of dividing ultimate curvature by yield curvature. the displacement ductility is expressed by displacement ductility ratio, the figure of dividing ultimate displacement by yield displacement

    論文中鋼筋延性採用鋼筋延性比b來表示，即極限應變與屈服應變的比值；構件截面延性採用截面延性比來表示，即極限曲率與屈服曲率的比值；構件位移延性採用位移延性比_來表示，即極限位移與屈服位移的比值。
  10. In two and three dimensions the yield limit is reached when a certain function of all the stress components reaches a fixed value.

    在二維或三維的情況下，當所有應力分量的某個函數達到某一固定值時可達到屈服極限。
分享友人
分享到 Line

分享到臉書